rockymounts SplitRail User manual

START HERE: 3-BIKE ASSEMBLY INSTRUCTIONS (PART 1)
Remove End Cap
Insert left and right bar into main spine.
Align 3 bike mark with end of spine. Install
4 M8x16 bolts with washers
Install Bars
Re-install end cap onto spine
Re-install End Cap
Install Wheel Tray
Install wheel tray with load arm facing out.
Install 4 M8x45 bolts
Remove end cap from main spine
Install Spacer
Fit gasket onto main spine followed by 2”
spacer. Install 2 M6x16 bolts and washers
Install Add-On Spine
Fit second gasket onto spacer followed by
Add On spine (two holes inside). Install 4
M6x16 bolts and washers
12
34
56

START HERE: 4-BIKE ASSEMBLY INSTRUCTIONS (PART 2)
2nd ADD-ON INSTRUCTIONS
Remove end cap from main spine Insert left and right bars into main spine.
Align 4 bike mark with end of main spine.
Install 4 M8x16 bolts and washers
Fit gasket onto main spine followed by add-on
spine (two holes inside). Install 4 M8x16 bolts
and washers.
Load wheel tray with load arm facing out.
Install four bolts
Remove back stop then stop bolt with 5mm
wrench
Remove screw and cap using a Phillips
head screwdriver
Remove Stop Bolt Remove Cap
Remove End Cap Install bars
Install 1st add-on Install 1st add-on
1
3
2
4
56

4-BIKE ASSEMBLY INSTRUCTIONS (PART 2 CONTINUED)
Remove 3 bolts with 4mm wrench. Flip
load arm 180°. Re-install bolts
Remove 2 bolts with 5mm wrench. Remove
hook and flip 180 degrees. Reinstall hook
and 2 bolts
Reinstall load arm on opposite side with 2
bearings. Reinstall the cap and screw.
Reinstall stop bolt and tighten pivot bolts
Re-install back stop Fit gasket onto spine followed by 2nd
add-on spine (holes on inside). Install 4
bolts and washers
Loosen 2 tension bolts with 4mm wrench.
Remove load arm with 2 bearings
78
910
11 12
Flip Load ArmRemove Load Arm
Flip Hook Reinstall Load Arm
Re-install Back Stop Install 2nd Add-on

4-BIKE ASSEMBLY INSTRUCTIONS (PART 2 CONTINUED)
NOTE: In the 4-bike configuration you will have the following extra parts
1x Spine Spacer, 1x Left Bar, 1x Right Bar, 2x Gaskets, 8x M8x 16 Bolts, 8x M8 Washers.
13 14
Load 2nd add-on wheel tray with load arm
facing out, install 4 bolts
Re-install end cap
Re-install End Cap
Install Wheel Tray
Not compatible with 1.25” SplitRail.
Do not use with Class 1 hitches.
Remove Baby Seats, Panniers, U-Locks, or items that could detach from the bicycle.
Do not use bicycle covers, bicycle bras, or bikes equipped with rear disc wheel.
Not intended for off road use. Not intended for use on trailers or towed vehicles.
Locks are only deterrents to thieves, RockyMounts, Inc. cannot be held liable for stolen bicycles.
Remove rack before entering a car wash.Remove rack before entering a car wash.
Check all fastenings (nuts, bolts, and straps) before each use.
Once a year, remove rack from car. Clean and inspect for damage.
Warnings
Lifetime Warranty
Thank you for purchasing a RockyMounts product. We take pride in providing a great customer experience and
manufacturing products that enable our customers to get their gear to their next colorful adventure.
As of January 1, 2014, RockyMounts products are covered for life to the original purchaser when used in accordance
with the instruction manuals’ assembly, installation and use guidelines.
If you feel something broke before it’s time; please email us at [e-mail] or call us at 800.873.1871.
For the most efficient service, email a digital photo (we need this photo to verify the problem) of the product in
questions, a brief description of the situation, and your purchase receipt. Our techs will respond within one business questions, a brief description of the situation, and your purchase receipt. Our techs will respond within one business
day. Most of the time we’ll replace the part in question, but we may ask for more details.
RockyMounts, Inc. warranty only covers RockyMounts, Inc. products. It does not cover theft, or damage to vehicles
and/or equipment.
All products purchased prior to Jan 1, 2014 are covered by a one-year warranty; see your product manual for details.
TM
TM