Rohl PERRIN & ROWE MAYFAIR LONDON U.4841LS-2 User manual

3
www.rohlhome.com
INSTALLATION INSTRUCTIONS
Consult your local ROHL showroom for additional information and specications. For complete warranty details and a list of showrooms, go to www.rohlhome.com.
Contemporary Mimas Mono Sink
Mixer with Rinse
Perrin & Rowe is a registered trademark of Avilion Ltd. 904885U Issue 3
Temp Range:
Min 1°C/34°F
Max 85°C/185°F
Recommended
Working Pressure:
Max5bar/75psi
Min 1bar/15psi
Ideal performance obtained with equal hot & cold pressures.
•U.4841LS-2 C-Spout Mono Mixer
•U.4846LS-2 C-Spout W/Rinse
*Where indicated please specify color
SPARES
1.3/8"
HOLE
1.1/8" HOLE
MIXER SERVICE KIT
9.54885
ROHLWARRANTY POLICY
All products supplied by ROHL carry warranties against manufacturing defects.
Perrin & Rowe products carry a Limited Lifetime Warranty.
ROHL LLC will provide free of charge, as its options, replacement part(s) or product (or a comparable alternative
product) to replace those which have proven defective in materials or workmanship.
For full ROHL LLC WARRANTY please contact ROHL or visit www.rohlhome.com
SPARE PARTS & SERVICE
3 Parker
Irvine
CA 92618
[phone]
www.rohlhome.com
The Contemporary Kitchen Collection
Installation & User Guide
Perrin & Rowe products are manufactured in the UK, using the latest
technology and built to the highest quality standards.
We would like to thank you for purchasing a Perrin & Rowe product and
take this opportunity to invite you to look at other luxury products by us.
Please contact us to recieve our latest catalogue.
9.12861*
9.17862*
9.25552 9.20867*
HOT IN
1/2"
COLD IN
1/2"
9 1/4" CRS
13/8" MAX
9 1/4" CRS
1. 3/8"
HOLE
HOT IN
1/2"
COLD IN
1/2"
1. 3/4" MAX
6" CRS
HOT IN
1/2" COLD IN
1/2"
1. 3/4" MAX
1. 3/8"
HOLE
•U.4842LS-2 Bar Spout Mixer
9.20860*
RINSE - 9.13842
NON-RINSE - 9.13843
9.07840
9.17862*
9.25552
9.26400
9.28735
9.28512
RINSE VERSION
9.18381*
9.12840*
9.01840*
9.26860*
9.13841
BAR SPOUT
9.18875*
Complete Rinse
Head
9.27878*
9.19426
Complete
Hose
9.28426*
9.20112*
9.25552
9.17862*

4
www.rohlhome.com
INSTALLATION INSTRUCTIONS
Consult your local ROHL showroom for additional information and specications. For complete warranty details and a list of showrooms, go to www.rohlhome.com.
Please Note: Ceramic disc valves are fitted as standard
to this mixer. Flow from FULLY OFF to FULLY ON is
achieved by rotating the handles a quarter turn.
CARE & MAINTENANCE
Wipe down after use to avoid water spotting and mineralbuild up.
Occasional cleaning with warm soapy water, followed by a polish with a soft cloth is all that is required to keep the
plated finish in good condition.
Do not use proprietary abrasive liquids, powders, or pads to clean the shower. Do not use any
products with ammonia bleach or limescale remover. You will damage the plated finish andvoidyour
guarantee.
BEFORE USE
• Carefully check the installation for leaks.
• If further building work is to be carried out in the vicinity, cover the tap with a plastic bag to avoid damaging
the finish.
• Please ensure that the installation complies with the water supply bye-laws.
If your mixer has a side spray please follow steps 2
& 3 to install correctly, otherwise please connect
Hot & Cold water supplies.
Secure side spray unit socket in a suitable position
using a faucet wrench or a 36 AF wrench.
Place flexible hose through top of side spray unit
socket as shown in diagram.
Screw flexible hose onto the end of side spray hose.
Ensure connections arefirmly tightened.
Ensure black rubber washer is in place before securing
side spray to flexible hose.
Holding the side spray, screw the flexible hose onto the
end of side spray and place into side spray unit socket.
Make sure orientation of side spray is correct.
Connect Hot & Cold water supplies to shanks.
Ensure all connections arefirmly tightened.
1
2
BASE RING
LARGE BASE
SEAL
SECURING NUT
BOX WRENCH
Secure spout with supplied Box Wrench.
Ensure all connections arefirmly tightened
• Temperature of the hot water supply does not exceed 185ºF.
• Recommended minimum water supply pressure - 25psi.
• Recommended maximum water supply pressure - 100psi.
• Ideal performance obtained with equalhot & cold pressures.
BASE SEAL
SIDE SPRAY UNIT
SOCKET
FIBRE WASHER
BACKNUT
SIDE SPRAY HOSE
BLACK RUBBER
WASHER
SIDE SPRAY
SIDE SPRAY
UNIT SOCKET
FLEXIBLE HOSE
Congratulations on the purchase of your Perrin & Rowe Kitchen Product. Correctly installed and with sensible care,
this product will give you many years of trouble free service.
The Contemporary Kitchen Collection
Installation & User Guide
IMPORTANT INFORMATION
The following instructions arefor therinse andnon-rinse version of the model you are installing.
Please read carefully to ensurecorrect installation.
Beforeyou proceed... Werecommendyou engage the servicesof aregistered plumber to install
this product.
For ease of possible future servicing, we also recommendthefittingof conveniently placed
isolatingvalves.
In addition to the guide below it is essential that thewritten information overleaf is carefully read
andunderstood.
Preparation Check Boxfor Installer
Flush the plumbing system before
installing the kitchen product.
Once unpacked remove large & small base seals,
rosette, fixing nut, securing nut and clamp plate
ready for installation.
CLAMP PLATE
3
Mimas - Lever should be on the right when viewed from the
front of the fitting. Hole centre a minimum of 2. 1/2" from the
wall.
Monobloc mixers require a Ø1. 3/8" hole through the surface they
are to be installed on. Maximum counter top thickness 1. 3/4".
Insert the flexible connections through the hole ensuring that the
base seal is in place between the mixer and mounting surface.
From the underside of the counter top, place the clamp plate on
the securing stud and using the box spanner supplied, put fixing
nut in spanner and tighten until mixer is held firmly in position.
SECURING
STUD

5
www.rohlhome.com
INSTALLATION INSTRUCTIONS
Consult your local ROHL showroom for additional information and specications. For complete warranty details and a list of showrooms, go to www.rohlhome.com.
Please Note: Ceramic disc valves are fitted as standard
to this mixer. Flow from FULLY OFF to FULLY ON is
achieved by rotating the handles a quarter turn.
CARE & MAINTENANCE
Wipe down after use to avoid water spotting and mineralbuild up.
Occasional cleaning with warm soapy water, followed by a polish with a soft cloth is all that is required to keep the
plated finish in good condition.
Do not use proprietary abrasive liquids, powders, or pads to clean the shower. Do not use any
products with ammonia bleach or limescale remover. You will damage the plated finish andvoidyour
guarantee.
BEFORE USE
• Carefully check the installation for leaks.
• If further building work is to be carried out in the vicinity, cover the tap with a plastic bag to avoid damaging
the finish.
• Please ensure that the installation complies with the water supply bye-laws.
If your mixer has a side spray please follow steps 2
& 3 to install correctly, otherwise please connect
Hot & Cold water supplies.
Secure side spray unit socket in a suitable position
using a faucet wrench or a 36 AF wrench.
Place flexible hose through top of side spray unit
socket as shown in diagram.
Screw flexible hose onto the end of side spray hose.
Ensure connections arefirmly tightened.
Ensure black rubber washer is in place before securing
side spray to flexible hose.
Holding the side spray, screw the flexible hose onto the
end of side spray and place into side spray unit socket.
Make sure orientation of side spray is correct.
Connect Hot & Cold water supplies to shanks.
Ensure all connections arefirmly tightened.
1
2
BASE RING
LARGE BASE
SEAL
SECURING NUT
BOX WRENCH
Secure spout with supplied Box Wrench.
Ensure all connections arefirmly tightened
• Temperature of the hot water supply does not exceed 185ºF.
• Recommended minimum water supply pressure - 25psi.
• Recommended maximum water supply pressure - 100psi.
• Ideal performance obtained with equalhot & cold pressures.
BASE SEAL
SIDE SPRAY UNIT
SOCKET
FIBRE WASHER
BACKNUT
SIDE SPRAY HOSE
BLACK RUBBER
WASHER
SIDE SPRAY
SIDE SPRAY
UNIT SOCKET
FLEXIBLE HOSE
Congratulations on the purchase of your Perrin & Rowe Kitchen Product. Correctly installed and with sensible care,
this product will give you many years of trouble free service.
The Contemporary Kitchen Collection
Installation & User Guide
IMPORTANT INFORMATION
The following instructions arefor therinse andnon-rinse version of the model you are installing.
Please read carefully to ensurecorrect installation.
Beforeyou proceed... Werecommendyou engage the servicesof aregistered plumber to install
this product.
For ease of possible future servicing, we also recommendthefittingof conveniently placed
isolatingvalves.
In addition to the guide below it is essential that thewritten information overleaf is carefully read
andunderstood.
Preparation Check Boxfor Installer
Flush the plumbing system before
installing the kitchen product.
Once unpacked remove large & small base seals,
rosette, fixing nut, securing nut and clamp plate
ready for installation.
CLAMP PLATE
3
Mimas - Lever should be on the right when viewed from the
front of the fitting. Hole centre a minimum of 2. 1/2" from the
wall.
Monobloc mixers require a Ø1. 3/8" hole through the surface they
are to be installed on. Maximum counter top thickness 1. 3/4".
Insert the flexible connections through the hole ensuring that the
base seal is in place between the mixer and mounting surface.
From the underside of the counter top, place the clamp plate on
the securing stud and using the box spanner supplied, put fixing
nut in spanner and tighten until mixer is held firmly in position.
SECURING
STUD