rojaflex WSR-1 User manual

Original Montageanleitung
Original instructions
Mode d‘emploi original
Instrucciones originales
Manuale d’uso originale
Originele gebruiksaanwijzing
Oryginalna instrukcja obsługi
Eredeti összeszerelési útmutató
IT
NL
PL
HUN
DE
EN
FR
ES
Eine aktuelle Vollversion der Anleitung finden Sie hier/
You can find a current full version of the manual here/
Vous trouverez ici une version complète et actuelle du mode d‘emploi/
Puede encontrar una versión completa actual del manual aquí/
Potete trovare una versione completa attuale del manuale qui/
Een actuele volledige versie van de handleiding vindt u hier/
Aktualną, pełną wersję podręcznika można znaleźć tutaj/
A kézikönyv aktuális, teljes verzióját itt találja:
https://www.rojaflex.com/bedienungsanleitungen.html
ORIGINAL ASSEMBLY AND
OPERATING INSTRUCTIONS
Rojaflex WSR-1 |WSR-2
For Rojaflex radio tubular motors and radio receivers
Wall transmitter
WSR-1_WSR-2_V5. 2022-05-23

2 www.rojaex.com
CONTENTS
General safety instructions 3 - 5
Function overview / 6
Changing the battery
Technical data / scope of delivery 7
Programming and settings 8 - 10
Notes 11
Contact information Back
Content
1| 2 - channel wall
transmitter
for Rojaflex radio tubular motors
and radio receivers
WSR-1
WSR-2
EU Declaration of Conformity according to Article 10(9):
Herewith declares Schoenberger Germany Enterprises GmbH & Co. KG, Hohenschäftlarn,
that the radio system type rojaflex handheld transmitter "WSR-1 | WSR-2" complies with the directive
2014/53/EU.
The full text of the EU Declaration of Conformity is available at the following Internet address:
www.rojaflex.com/konformitaetserklaerungen.html
Art.-Nr.
WSR-1 90100084
WSR-2 90100085
ATTENTION!
After unpacking, compare the device type with
the corresponding information on the type
plate.Incomplete devices or devices that do not
comply with the information must not be put into
operation and a complaint must be lodged with
our customer service (see contact information)
before commissioning.

www.rojaex.com 3
General safety instructions
WARNING!
Important safety instructions!
• For the safety of persons it
is important to follow these
instructions!
• Please keep the manual and hand
it over to the new owner in case of
change of ownership!
• This appliance can be used by
children aged from 8 years and
above and persons with reduced
physical, sensory or mental
capabilities or lack of experience
and knowledge if they have been
given supervision or instruction
concerning use of the appliance
in a safe way and understand the
hazards involved.
• Children are not allowed to play with
the device.
• Cleaning and maintenance by the
user must not be carried out by
children without supervision.
WARNING!
The motor controlled by the radio
control (the transmitter) must be
disconnected from its power source
during cleaning, maintenance and
replacement of parts!
WARNING!
There is a danger to life from electric
shock when working on electrical
equipment!
Observe the instructions and safety
instructions of the drive/receiver
controlled by the radio control as well
as the corresponding instructions
of the driven roller shutter or sun
protection system!
ATTENTION!
The following instructions must be
observed!
The range of radio controls is regulated by
the legal requirements for radio systems
and is influenced by structural conditions,
among other things.
When planning, make sure you have
adequate radio reception.
This is especially true if the radio
transmitter is located in a different room
than the radio receiver, and therefore
the radio signal must penetrate walls or
ceilings.
Do not install the radio control in the
direct vicinity of large metallic surfaces.
Other transmitting equipment (e.g.
radio headphones, baby monitors, radio
weather stations) whose transmission
frequency is identical to that of the radio
control unit may interfere with reception.
Attention!
It is essential to observe the instructions
for correct use and the operating
conditions!
In case of improper use, there is
an increased risk of damage to the
controlled system!
• Use the radio control (transmitter)
only for connection to roller shutter,
awning and blind motors or their
receivers.

4 www.rojaex.com
General safety instructions
• Deactivate the automatic functions
of the radio control in case of
snowfall, icing or danger of frost to
avoid damage to the motor or the
driven equipment.
• Only use original components and
accessories from the manufacturer.
• Instruct all persons in the safe use
of the radio control and the motor
controlled by it.
• During commissioning, observe the
moving equipment (roller shutter,
awning, blind) and keep people
away from it until the movement is
finished.
• Prohibit children from playing with
the radio control.
• Store the handheld transmitter
in such a way that unintentional
operation, e.g. by children playing, is
prevented.
• Secure the controlled system against
unauthorized operation.
• Take safety precautions against
unintentional switch-on.
• Carry out all cleaning work on the
system in a de-energized state.
• Use caution when operating the
open/extended system as parts may
fall if fasteners (e.g. springs) weaken
or are broken.
• Never use defective or damaged
equipment.
• Check that the motor controlled
by the radio control and the motor
power cable are intact.
WARNING!
The use of faulty equipment can
endanger persons and cause damage
to property.
Regularly check the radio control
and the system it controls for proper
functioning and keep people away
from it until the check for proper
functioning has been completed!
Please contact our service department
(see "Contact information" page) if you
notice any damage to the device.
ATTENTION!
After unpacking, compare the
device type with the corresponding
information on the type plate.
Incomplete devices or devices that do
not meet the specifications must not be
put into operation.
IMPORTANT!
Disposal instructions!
(European Directive 2012/19/EU (WEEE)
Our electrical and
electronic products are
marked with a crossed-
out wheeled garbage
can, indicating that
these products and
any batteries they
may contain must be
collected separately at
the end of their useful
life and must not be disposed of with
normal household waste.

www.rojaex.com 5
General safety instructions
The substances contained in these
products may have negative effects on
health and the environment, so users of
electrical products and batteries also have
a responsibility in recycling these waste
materials and in this way contribute to the
protection, preservation and improvement
of the environment.
Obligation for separate disposal
Our duty as manufacturers is, among other
things, to inform you of your obligation to
separate disposal.
• When disposing of products with
batteries, remove them from the
product and dispose of them separately.
• When disposing of illuminants, they
must be disposed of separately to the
receptacle.
Return option and
Recycling program EU
We are connected to public-law return
systems throughout Europe and thus
offer our customers access to a Europe-
wide network of local recycling facilities
(recycling centers, take-back points or
similar).
Our products are professionally recycled
via these local facilities. This reduces the
amount of waste - to the benefit of the
environment.
Our registration numbers:
*For registration data of other European
countries, see Contact Information page.
A take-back by us as manufacturer
according to §19 WEEE is not to be asserted.
Information on the degree of fulfillment
of the collection and recycling
requirements
It is also our duty as a manufacturer to
inform you about the degree of fulfillment
of the collection and recycling requirements.
Since we are connected to a qualified take-
back system, we can refer to the degree of
fulfillment of the recycling companies.
You can find this information on our
website.
Deletion of personal data
Some of our products contain personal data.
This applies in particular to information and
telecommunications technology devices
such as computers and smartphones. In
your own interest, please note that each end
user is responsible for deleting the data on
the old devices to be disposed of!
Reg. no.*
WEEE DE 41060608
Battery DE 88866710
Illuminant
Transport and
Shipping packaging DE5768543732165

Inserting the battery / changing the battery
The battery is (depending on the transmitter model) supplied loose or already installed and secured against
discharge with a protective foil. Open the battery compartment by turning the cover (e.g. with a coin),
remove the protective film and insert the battery into the battery compartment with the + (plus) side facing
up.
Then close the battery compartment again.
1-channel wall transmitter
WSR-1
STOP
DOWN
UP
2-channel wall transmitter
WSR-2
STOP
DOWN
UP
*with the “IP” switch it is possible to choose
between “SI” (Single = one-way communi-
cation) and “BI” (two-way communication)
- radio, depending on the radio receiver
(see receiver manual).
SI BI
O
p
e
n
-
C
l
o
s
e
UP
Battery com-
partment
DIP switch* One-
way / two-way
communication
Orientation
guide
P2 Program-
ming key
channel 1
P2 Programming
key channel 2
(WSR-2 only)
Wall Transmitter WSR-1
/ WSR-2- Backside
6 www.rojaex.com
Function overview / changing the battery
Depending on the frequency of switching
operations, we recommend replacing the
battery at least every 2 years.
Please do not dispose of batteries in
household waste! Take them to an
appropriate disposal station.
ATTENTION!
Do not swallow the battery!
Danger of chemical burns!

Performance Features:
Input voltage 3V (battery CR2450)
Transmit frequency 433.05 - 434.79 MHz
Operating current ≤ 15mA
Quiescent current ≤ 10 μA
Standby consumption ≤ 3 μW
Transmitting power ≤ 10 mW
Protection class IP 20
Permissible ambient tempe-
rature +10°C to +50°C
Range Free field: approx. 150 m /
indoors: approx. 30 m *
Channels 1-channel | 2-channels
Compatibility Rojaflex radio motors and radio receivers
Radio system Rolling Code
Dimensions (approx.) (HxWxD) 50 mm × 50 mm × 14 mm
Technical data
Scope of delivery
When unpacking, please compare the package contents with the information on the scope of delivery in
these instructions!
1. Wall transmitter incl. battery and outer frame
2. Fastening material
3. Instruction manual
* Range data are approximate values and depend on the structural conditions.
1
Original Montageanleitung
Original instructions
Mode d‘emploioriginal
Instruccionesoriginales
Manuale d’uso originale
Originelegebruiksaanwijzing
Oryginalnainstrukcja obsługi
Eredeti összeszerelésiútmutató
IT
NL
PL
HUN
DE
EN
FR
ES
Voustrouverez ici une version complète et actuelle du mode d‘emploi/
Puede encontraruna versión completa actual del manual aquí/
Potetetrovare una versione completa attuale del manuale qui/
Een actuele volledige versie van de handleiding vindt u hier/
Aktualną, pełną wersję podręcznika można znaleźć tutaj/
A kézikönyv aktuális, teljes verzióját itt találja:
BEDIENUNGSANLEITUNG
|WSR-2
Wandsender
WSR-1_WSR-2_V5. 2022-04-29
32
or
www.rojaex.com 7
Technical data / scope of delivery

1. Programming mode - radio receiver or radio motor
Set the receiver (external Rojaflex radio receiver or Rojaflex radio motor) on which the handheld transmitter
is to be programmed to programming mode (see receiver instructions).
2. Programming the wall transmitter - WSR-1
Each keystroke must be executed within 4 seconds!
Otherwise, the system automatically exits the programming mode.
SI BI
O
p
e
n
-
C
l
o
s
e
UP
Set receiver (motor / external
receiver) to programming
mode according to instruc-
tions.
Press P2 programming key
(rear) 2 times.
Press UP key 1 x
press.
The motor (shutter) briefly
moves UP/DOWN and/or the
receiver beeps.
OK!
First code programming suc-
cessfully performed.
Then check the function by pressing the UP / STOP / DOWN keys.
If the direction of rotation of the motor is reversed (roller shutter / motor moves downwards when
the UP key is pressed), please start from the beginning and press the DOWN key after the P2 key
instead of the UP key!
This changes the direction of rotation of the motor.
Changing the direction of rotation of the motor is only possible, depending on the motor
type, if the end positions of the motor have not yet been programmed!
8 www.rojaex.com
Programming and settings

2.1 Programming the wall transmitter - WSR-2
Each keystroke must be executed within 4 seconds!
Otherwise, the system automatically exits the programming mode.
Press P2 programming key
(rear) 2 times.
Upper key P2 = channel 1
Lower key P2 = channel 2
Set receiver (motor / external
receiver) to programming
mode according to instruc-
tions.
Press UP key of the desired
channel 1 x.
Channel 1 = Left buttons
Channel 2 = Right buttons
The motor (shutter) briefly
moves UP/DOWN and/or the
receiver beeps.
OK!
First code programming suc-
cessfully performed.
SI BI
O
p
e
n
-
C
l
o
s
e
UP
Then check the function by pressing the UP / STOP / DOWN keys.
If the direction of rotation of the motor is reversed (roller shutter / motor moves downwards when
the UP key is pressed), please start from the beginning and press the DOWN key after the P2 key
instead of the UP key!
This changes the direction of rotation of the motor.
Changing the direction of rotation of the motor is only possible, depending on the motor
type, if the end positions of the motor have not yet been programmed!
www.rojaex.com 9
Programming and settings

3. Add wall transmitter
Press the P2 programming
button (back) 3 times on
a wall transmitter that has
already been programmed.
Upper key P2 = channel 1
Lower key P2 = channel 2
Then press the P2 program-
ming button (back) once on
the wall transmitter to be
reprogrammed.
The motor (shutter) briefly
moves UP/DOWN and/or the
receiver beeps.
OK!
First code programming suc-
cessfully performed.
SI BI
O
p
e
n
-
C
l
o
s
e
UP
SI BI
O
p
e
n
-
C
l
o
s
e
UP
Important: For systems with SI (single-directional system / one-way communication), the P2
button of the already programmed wall transmitter is pressed only 2 times!
This applies, for example, to the MLSF/MLMF drives and the REHK-1 and RUE-UP external recei-
vers.
Please follow the instructions of the respective receiver/motor!
Individual deletion of hand-held or wall-mounted transmitters is NOT possible!
4. Delete wall transmitter
For further information, please refer to the instructions of the Rojaflex radio tubular motors or
radio receivers.
1. Power is ON (motor is connected and ready for operation).
2. Press P2 programming key 1 x. Motor beeps 1 x.
3. Press STOP key 1 x. Motor beeps 1 x.
4. Press P2 programming key 1 x. Motor beeps 3 x*.
OK! ALL wall (hand) transmitters are deleted!
*The frequency of the beeps or the reaction of the motor / shutter depends on the receiver.
Please observe the corresponding instructions of the respective receiver/motor!
10 www.rojaex.com
Programming and settings

www.rojaex.com 11
Notes

Reprints, including excerpts, only with the permission of the author.
Product changes, which from our point of view serve to improve quality,
can be made at any time, even without prior notice or notification.
Illustrations can be example illustrations, which differ in appearance from
the delivered goods.
Errors excepted. No liability is assumed for printing errors.
Our general terms and conditions apply.
If you have any questions about this product,
please contact us at the following address:
rojaflex
is a registered trademark of
Schoenberger Germany Enterprises GmbH & Co. KG
Zechtraße 1-7
82069 Hohenschäftlarn
Germany
T +49 (0) 8178 / 93 29 93 93
F +49 (0) 8178 / 93 29 93 94
info@rojaflex.com
www.rojaflex.com
EU Waste and recycling / Registrations
Germany for electrical devices:
Stiftung EAR
WEEE-Reg.-no.: DE 41060608
Germany for batteries:
Stiftung EAR
Batt-Reg.-no.: DE 88866710
Germany for packaging:
LUCID Reg.-no.: DE5768543732165
Austria for electrical devices:
Elektro Recycling Austria (ERA) GmbH
ERA Contract no: 40801
Austria for packaging:
Altstoff Recycling Austria (ARA) AG
ARA License number: 23363
Switzerland for electrical devices:
Stiftung SENS
Membership number: VP11544
France for electrical devices:
Ecologic
Membership number / Take-back system: M3670
National registry: UIN FR208795_01SUIN
France for packaging:
Citeo
Membership number / Take-back system: 532886
National registry: UIN FR208795_01SUIN
Spain for electrical devices:
ECOTIC
Reg.-no.: RII-AEE- 7601
Spain for packaging:
Ecoembes
Membership number: 97556
Italy for electrical devices:
Raccolta differenziata. Verifica le disposizioni del tuo Comune!
Reg.-no.: n/a
Italy for packaging:
Raccolta differenziata. Verifica le disposizioni del tuo Comune!
Membership number: n/a