Roland TrueVIS VG2-640 User manual
• Thank you very much for purchasing this product.
• To ensure correct and safe usage with a full understanding of this product's performance, please be sure to read
through this manual completely and store it in a safe locaon.
• Unauthorized copying or transferal, in whole or in part, of this manual is prohibited.
• The specicaons of this product and the contents of this operaon manual are subject to change without no-
ce.
• This manual and the product have been prepared and tested as much as possible. If you nd any misprints or
errors, please inform Roland DG Corporaon.
• Roland DG Corporaon assumes no responsibility for any direct or indirect loss or damage that may occur
through use of this product, regardless of any failure to perform on the part of this product.
• Roland DG Corporaon assumes no responsibility for any direct or indirect loss or damage that may occur with
respect to any arcle made using this product.
R1-190208
Setup Guide
This machine has a built-in inductive reading/writing communication device that uses radio waves (an RFID device).
• RFID is used to read the informaon inscribed on the ink pouches (or cartridges).
• If you use a pacemaker or other implanted medical equipment, do not approach this machine.
• Do not use this machine within hospitals.
Important notes on Bluetooth communication
• This machine supports the operaon applicaon, which is an applicaon for mobile terminals. When
using the operaon applicaon, set this machine's Bluetooth communicaon to "ENABLE." However,
when you are operang this machine from its operaon panel, you cannot perform operaons from
the operaon applicaon.
• With Bluetooth wireless technology, it is possible to establish a connecon between devices separated
by approximately 10 m (32.8 .). However, the valid range of the connecon may vary depending on
the presence of obstacles (such as people, metal, and walls) and the status of the radio waves.
• The communicaon status of the Bluetooth connecon may become unstable if:
¾A wireless LAN is in place in the locaon.
¾The devices are in the vicinity of a microwave that is in use.
¾Other electromagnec waves are generated in the locaon.
• Bluetooth communicaon uses the same frequency band (2.4 GHz) as wireless LAN (IEEE802.11b/
g). If the devices are used in the vicinity of equipment in which a wireless LAN unit is installed, the
connecon status may become unstable due to the occurrence of radio-frequency interference. In this
situaon, carry out the following countermeasures.
¾When using Bluetooth communicaon to connect the printer and the mobile terminal, do so at
a distance of 10 m (32.8 .) or more away from the equipment in which a wireless LAN unit is
installed.
¾Bring the mobile terminal and the printer as close together as possible.
¾If using Bluetooth communicaon within 10 m (32.8 .) of the equipment in which a wireless LAN
unit is installed, turn o the wireless LAN unit.
• The radio waves generated by Bluetooth communicaon may have an eect on the operaon of
electronic medical equipment and similar devices. This may lead to accidents, so turn o Bluetooth
communicaon in the following locaons.
¾The vicinity of in-use hearing aids and pacemakers
¾Hospitals
¾The vicinity of automac doors and re alarms
• Using Bluetooth communicaon in the vicinity of TVs or radios may lead to noise in the image or au-
dio.
• Roland DG Corporaon accepts no responsibility for the leakage of informaon during a connecon
using Bluetooth technology.
• The mobile terminal that you are using to connect to the printer must comply with Bluetooth stan-
dards determined by the Bluetooth SIG and must be a cered device.
• Even if the mobile terminal complies with the Bluetooth standards outlined above, phenomena may
occur due to the characteriscs and specicaons of the device. Examples of these phenomena in-
clude the inability to connect to the printer and the operaon methods, display, and operaons being
dierent.
• Depending on the mobile terminal that you are connecng to the printer, it may take some me unl
the Bluetooth connecon can be established.
1
Company names and product names are trademarks or registered trademarks of their respecve holders.
Copyright © 2019 Roland DG Corporaon
Contents
This document is the setup guide for the VG2-640/540. This document uses the following notaons to disnguish
between the models where necessary.
VG2-640 — 64-inch model
VG2-540 — 54-inch model
Most of the gures in this document depict the VG2-640.
1
5
12
1. Introducon ...............................................................................................19
20
20
21
21
22
22
23
2. Installaon .................................................................................................25
26
26
27
30
34
40
42
43
44
45
47
51
52
52
53
55
55
57
60
3. Appendix ...................................................................................................61
62
63
This product uses GNU General Public License (GPL)/GNU Lesser General Public License (LGPL) software. You have the
right to acquire, modify, and distribute the source code for this GPL/LGPL software. You can obtain the GPL/LGPL
source code used in this product by downloading it from the following website:
URL: https://www2.rolanddg.com/gpl/
Copyright (c) 2012 - 2013, Murata Manufacturing Co., Ltd. All rights reserved.
Redistribution and use in source and binary forms, with or without modication, are permitted provided that the
following conditions are met:
-Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR
IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
For the USA and Canada
FCC CAUTION
Changes or modications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
This device complies with Part 15 of FCC Rules and Industry Canada’s licence-exempt RSSs. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
------
Le présent appareil est conforme à la partie 15 des règles de la FCC et aux normes des CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1)
l'appareil ne doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement.
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets
the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This
equipment has very low levels of RF energy that is deemed to comply without maximum permissive exposure
evaluation (MPE).
------
Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non
contrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes directrices d'exposition et d’exposition aux
fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui est considérée
comme conforme sans évaluation de l’exposition maximale autorisée (MPE).
2
For the USA
FEDERAL COMMUNICATIONS
COMMISSION RADIO FREQUENCY
INTERFERENCE STATEMENT
Responsible Party : Roland DGA Corporation
Address : 15363 Barranca Parkway Irvine, CA 92618 U.S.A.
Telephone : 949-727-2100
Type of Equipment :Printer
Model Name :VG2-640, VG2-540
NOTE:
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
FCC CAUTION
Changes or modications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
Use only I/O cables that have been designed and
manufactured specically for this device.
For Canada
CAN ICES-3 (A)/NMB-3(A)
For California
WARNING:This product can expose you to chemicals
including lead,which is known to the State of California to
cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov.
For EU Countries
WARNING
Operation of this equipment in a residential environment
could cause radio interference.
For EU Countries
Manufacturer:
ROLAND DG CORPORATION
1-6-4 Shinmiyakoda, Kita-ku, Hamamatsu-shi, Shizuoka-ken,
431-2103 JAPAN
The importer in the EU:
Roland DG Europe Holdings B.V.
Prof. J.H. Bavincklaan 2, 1183 AT, Amstelveen, The Netherlands
NOTICE
Grounding Instructions
• In the event of a malfunction or breakdown, grounding
provides a path of least resistance for electric current to
reduce the risk of electric shock. This tool is equipped with an
electric cord having an equipment-grounding conductor and
a grounding plug. The plug must be plugged into a matching
outlet that is properly installed and grounded in accordance
with all local codes and ordinances.
• Do not modify the plug provided - if it will not t the outlet,
have the proper outlet installed by a qualied electrician.
• Improper connection of the equipment-grounding conductor
can result in a risk of electric shock. The conductor with
insulation having an outer surface that is green with
or without yellow stripes is the equipment-grounding
conductor. If repair or replacement of the electric cord or
plug is necessary, do not connect the equipment-grounding
conductor to a live terminal.
• Check with a qualied electrician or service personnel if the
grounding instructions are not completely understood, or if
in doubt as to whether the tool is properly grounded.
• Use only 3-wire extension cords that have 3-prong grounding
plugs and 3-pole receptacles that accept the tool’s plug.
• Repair or replace damaged or worn cord immediately.
4
For China
产品中有毒有害物质或元素的名称及含量
部件名称
有毒有害物质或元素
铅(Pb) 汞(Hg) 镉(Cd) 六价铬
(Cr(Ⅵ))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
印刷电路板 × ○× ○○○
头部 × ○○○○○
壳体、底架 × ○○○○○
电源 × ○× ○○○
其他（电缆、附件等） × ○○○○○
○：表示该有毒有害物质在该部件所有均质材料中的含量均在 GB/T26572-2011 标准规定的限量要求以下。
×：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GB/T26572-2011 标准规定的限量要求。
环保使用期限
此标志适用于在中国国内销售的电子信息产品，表示环保使用期限的年数。
所谓环保使用期限是指在自制造日起的规定期限内，产品中所含的有害物质
不致引起环境污染，不会对人身、财产造成严重的不良影响。
环保使用期限仅在遵照产品使用说明书，正确使用产品的条件下才有效。
不当的使用，将会导致有害物质泄漏的危险。
For EU countries
This product must be disposed of
separately at your local waste recycling
center. Do not dispose of in household
waste bin.
Bitte führen Sie dieses Produkt separat
Ihrer örtlichen Entsorgungsstelle zu.
Bitte nicht mit dem normalen Hausmüll
entsorgen.
Ne jetez pas le produit avec vos
ordures ménagères. Portez-le dans un
centre recyclage des déchets.
Questo prodotto deve essere smaltito
negli appositi contenitori per la raccolta
differenziata, non buttare nel cestino
dei rifiuti casalinghi.
Este producto debe devolverse al
centro de reciclaje más cercano a su
domicilio para su correcta eliminación.
No lo tire a la basura.
Deite fora separadamente este produto
no seu centro de reciclagem local. Não
o deite fora no seu caixote do lixo.
Lever dit product in bij een lokaal
afvalverzamelpunt. NIET met normaal
huishoudelijk afval afvoeren.
Dette Produkt skal smides særskilt
væk på den lokale affalds- og
genbrugsstation. Må ikke smides ud
sammen med almindeligt
husholdningsaffald.
Tätä tuotetta ei saa hävittää
normaalien talousjätteiden mukana,
vaan se on toimitettava
ongelmajätteiden keräilypisteeseen
hävitettäväksi.
Produkten måste kasseras separat på
din lokala återvinningscentral. Släng
inte produkten tillsammans med
hushållssoporna.
Μην πετάξετε το αντικείμενο αυτό στο
καλάθι των απορριμμάτων. Αφαιρέστε
τις μπαταρίες και προσκομίστε το στο
τοπικό κέντρο ανακύκλωσης.
To Ensure Safe Use
About WARNING and CAUTION Noces
WARNING
CAUTION
About the Symbols
5
This is a heavy machine.
WARNING
Install the machine in a locaon that
is level, stable, and able to bear the
weight of the machine aer checking
the weight of the machine in the oper-
aon manual on the installaon of the
machine.
Unloading and emplacement are
operaons that must be performed by
the specied number of the workers or
more as referring to the operaon man-
ual on the installaon of the machine.
Be sure to lock the stand’s casters.
When storing roll media, implement
adequate safety measures to ensure
that the stored media will not roll, fall,
or topple over.
WARNING
Handling roll media is an operaon that
must be performed by two persons or
more, and care must be taken to pre-
vent falls.
Be sure to use the adjuster to secure
the stand in place (in case the stand is
equipped with an adjuster). Ensure that
the adjuster is not loose.
To Ensure Safe Use
6
WARNING
Be sure to follow the operaon proce-
dures described in the user’s manual.
Never allow anyone unfamiliar with the
usage or handling of the machine to
touch it.
Keep children away from the machine.
Never operate the machine while red
or aer ingesng alcohol or any medica-
on.
Always unplug the power cord when
aaching or removing parts and oponal
parts and when performing cleaning or
maintenance that does not require the
machine to be connected to a power
source.
Never aempt to disassemble, repair, or
modify the machine.
CAUTION
Exercise cauon to avoid being pinched
or becoming caught.
Never aempt operaon while wearing a
necke, necklace, or loose clothing. Bind
long hair securely.
Conduct operaons in a clean, brightly lit
locaon.
Never climb or lean on the machine.
Cauon: cung tool.
Cauon: sharp components.
Incorrect operation may cause injury
To Ensure Safe Use
7
Danger of electrical short, shock, electrocution, or re
WARNING
Connect to an electrical outlet that
complies with this machine’s rangs (for
voltage, frequency, and current).
Never use outside or in any locaon
where exposure to water or high humid-
ity may occur. Do not touch the power
cord, plug, or electrical outlet with wet
hands.
Never allow any foreign object to get in-
side. Never expose the machine to liquid
spills.
Never place any ammable object
nearby. Never use a combusble aerosol
spray nearby. Never use in any locaon
where gases can accumulate.
Handle the power cord, plug, and electri-
cal outlet correctly and with care. Never
use any arcle that is damaged.
When using an extension cord or power
strip, use one that adequately sases
the machine’s rangs (for voltage, fre-
quency, and current).
Connect to ground.
WARNING
Posion so that the power plug is within
immediate reach at all mes.
If sparking, smoke, burning odor, unusual
sound, or abnormal operaon occurs,
immediately unplug the power cord.
Never use if any component is damaged.
Do not use the supplied power cord for
other products.
Never use the machine for any purpose
for which it is not intended, or use the
machine in an undue manner that ex-
ceeds its capacity.
For accessories (oponal and consum-
able items, power cord, and the like), use
only genuine arcles compable with
this machine.
To Ensure Safe Use
8
Important notes about the power cord, plug, and electrical outlet
Never place any object on top or
subject to damage.
Never allow to get wet. Never bend or twist with undue
force.
Never make hot. Never pull with undue force. Dust may cause re.
Never bundle, bind, or roll up.
Danger of re, burns, or toxic gas emissions
WARNING
Caution: high temperatures
Remove any loaded media or switch off
the sub power when printing is not being
performed.
WARNING
Never use media that cannot withstand
heat.
To Ensure Safe Use
9
In the event of ingestion or physical distress
•
•
•
•
*
WARNING
Keep open ame away from the work
area.
Never store ink, cleaning liquid, or
discharged uid in any of the following
locaons.
• Any location exposed to open ame
• Any location where high temperature may
occur
• Near bleach or any other such oxidizing agent
or explosive material
• Any location within the reach of children
Never place an ink container (such as a
cartridge or pouch) in re.
Never drink or sni ink, cleaning liquid,
or discharged uid, or allow them to
come in contact with the eyes or skin.
CAUTION
Ensure adequate venlaon for the work
area.
Never allow an ink container (such as a
cartridge or pouch) to be subjected to
impact, and never aempt to disassem-
ble.
Ink, cleaning liquid, and discharged uid are ammable and toxic
To Ensure Safe Use
10
Warning Labels
Cauon: High Temperature
Cauon: Pinching Hazard
Cauon: Moving Print Heads
Ink, cleaning uid, and discharged uid are ammable and toxic.
Cauon: High Voltage
Flammable
To Ensure Safe Use
11
Pour utiliser en toute sécurité
À propos des avis ATTENTION et PRUDENCE
ATTENTION
PRUDENCE
À propos des symboles
12
Cet appareil est lourd.
ATTENTION
Installer l’appareil à un endroit stable et
plat et capable de supporter son poids
après avoir vérié le poids de l’appareil
indiqué dans le manuel d’installaon de
cee machine.
Le déchargement et la mise en place
doivent être exécutées par un nombre
spécique de travailleurs ou plus, comme
il est indiqué dans le mode d’emploi au
moment de l’installaon de l’appareil.
S’assurer de verrouiller les roulees de la
base.
ATTENTION
Lors de l’entreposage du rouleau de
média, prendre les mesures de sécurité
adéquate pour s’assurer que le rouleau
ne roulera pas, ne tombera ni ne bascul-
era pas.
La manutenon du support en rouleau
doit être faite par deux personnes ou
plus et il faut prendre des précauons
pour éviter les chutes.
S’assurer d’uliser le disposif de réglage
pour xer solidement la base en posion
(si la base est munie d’un disposif de
réglage). Vérier que le disposif de
réglage est bien serré.
Pour utiliser en toute sécurité
13
ATTENTION
S’assurer de suivre les procédures d’ul-
isaon décrites dans le manuel ulisa-
teur. Ne jamais permere à quiconque
ne connaît pas le fonconnement ou la
manutenon de l’appareil de le toucher.
Garder les enfants loin de l’appareil.
Ne jamais faire fonconner l’appareil
après avoir consommé de l’alcool ou des
médicaments, ou dans un état de fague.
Toujours débrancher le câble d’alimen-
taon lors de la xaon ou du retrait
de pièces et de pièces en opon et du
neoyage ou des travaux d’entreen qui
n’exigent pas un branchement de l’appar-
eil à une source d’alimentaon.
Ne jamais tenter de démonter, de répar-
er ou de odier l’appareil.
PRUDENCE
Faire preuve de prudence pour éviter
l’écrasement ou le coincement.
Ne jamais faire fonconner l’appareil si
on porte une cravate, un collier ou des
vêtements amples. Bien aacher les
cheveux longs.
Uliser l’appareil dans un endroit propre
et bien éclairé.
Ne jamais grimper ni s’appuyer sur la
machine.
Aenon : oul de coupe.
Aenon : composants acérés.
L’utilisation incorrecte peut causer des blessures
Pour utiliser en toute sécurité
14
Risque de décharge ou de choc électrique, d’électrocution ou d’incendie
ATTENTION
Brancher à une prise électrique conforme
aux caractérisques de cet appareil (ten-
sion, fréquence et courant).
Ne jamais uliser à l’extérieur ni à un
endroit où l’appareil risque d’être exposé
à de l’eau ou à une humidité élevée.
Ne pas toucher le câble d’alimentaon,
la che ou la prise électrique avec des
mains mouillées.
Ne jamais insérer d’objet étranger dans
l’appareil. Ne jamais exposer l’appareil
aux déversements de liquides.
Ne jamais placer d’objet inammable à
proximité de l’appareil. Ne jamais uliser
de produit inammable en aérosol à
proximité de l’appareil. Ne jamais uliser
l’appareil dans un endroit où des gaz
peuvent s’accumuler.
Manipuler le câble d’alimentaon, la
che et la prise électrique correctement
et avec soin.
Ne pas uliser le cordon électrique four-
ni avec d’autres produits.
ATTENTION
Si une rallonge ou une bande d’alimen-
taon électrique sont ulisées,s’assurer
qu’elles correspondent aux caractéris-
ques de l’appareil (tension,fréquence et
courant).
Mise à la terre.
Placer l’appareil de façon à ce que la
che soit facile d’accès en tout temps.
S’il se produit des éncelles, de la
fumée,une odeur de brûlé, un bruit in-
habituel ou un fonconnement anormal,
débrancher immédiatement le câble
d’alimentaon.
Ne jamais uliser l’appareil à des ns
autres que celles pour lesquelles il est
conçu. Ne jamais l’uliser de manière
abusive ou d’une manière qui dépasse sa
capacité.
Uliser uniquement des accessoires
d’origine (accessoires en opon, arcles
consommables, câble d’alimentaon et
autres arcles semblables), compables
avec l’appareil.
Pour utiliser en toute sécurité
15
Ne jamais déposer aucun objet
dessus au risque de les endom-
mager.
Ne jamais laisser mouiller. Ne jamais plier ni enrouler.
Ne jamais chauer. Ne jamais rer avec une force
excessive.
La poussière peut causer un in-
cendie.
Ne jamais plier ni tordre avec une
force excessive.
Remarques importantes à propos du câble d’alimentation, de la che et de la prise électrique
Risque d’incendie, de brûlures ou d’émissions de gaz toxiq
ATTENTION
Aenon : températures élevées.
Quand aucun travail d’impression n’est
en cours, rerer tout support de l’appareil
ou couper l’alimentaon électrique.
ATTENTION
Ne jamais uliser un support qui ne peut
pas supporter la chaleur.
Pour utiliser en toute sécurité
16
L’encre, les liquides nettoyants et les liquides usées sont inammables et toxiques
ATTENTION
Ne pas approcher une amme nue de
l’espace de travail.
Ne jamais entreposer d’encre, de liquide
de neoyage ou des liquides usés dans
les endroits suivants :
• un endroit exposé à une amme nue;
• un endroit où il y a risque de température
élevée;
• près d’eau de Javel, d’un autre agent d’oxyda-
tion ou de matériel explosif;
• tout endroit à la portée d’enfants;
Ne placez jamais un récipient d’encre (tel
qu’une cartouche ou une poche) dans le
feu.
ATTENTION
Ne jamais boire l’encre, le liquide de
neoyage ni les liquides usés, ne pas en
respirer les vapeurs et ne pas laisser les
produits entrer en contact avec les yeux
ou la peau.
PRUDENCE
S’assurer que le lieu de travail est bien
aéré.
Ne jamais soumere un réservoir d’encre
(cartouche ou poche) aux impacts et ne
jamais tenter de le démonter.
En cas d’ingestion ou de trouble physique
• En cas de contact avec les yeux : rincer immédiatement et abondamment à l’eau courante pendant au
moins 15 minutes. Si les yeux sont toujours irrités, consulter un médecin.
• En cas de contact avec la peau : laver immédiatement à l’eau et au savon. En cas d’irritation ou
d’inammation de la peau : consulter un médecin.
• En cas d’ingestion : ne pas provoquer le vomissement et demander immédiatement l’aide d’un
médecin. Provoquer le vomissement peut créer un risque de suocation.
• Si l’odeur cause un trouble physique, amener la personne dans un endroit bien aéré et la faire se
reposer. Si l’étourdissement ou la nausée persistent, consulter un médecin.
* Se référer à la che technique de sécutité (SDS = safety data sheet) pour toute information sur les
produits chimiques contenus dans l’encre et les instructions de sécurité associées.
Pour utiliser en toute sécurité
17
Vignettes d'avertissement
Aenon : Température élevée
Aenon : Risque de pincement
Aenon : Têtes d'impression mobiles
L’encre, le liquide de neoyage et le rejet liquide sont toxiques
Aenon : voltage élevé
Inammable
Pour utiliser en toute sécurité
18
Other manuals for TrueVIS VG2-640
2
This manual suits for next models
1
Table of contents
Other Roland Printer manuals
Roland
Roland LEC-300 User manual
Roland
Roland CammJet CJ-500 User manual
Roland
Roland FLATJET Series User manual
Roland
Roland SOLJET PRO4 XF-640 User manual
Roland
Roland VersaART RS-640 User manual
Roland
Roland VersaCAMM ECO-SOL MAX3 User manual
Roland
Roland SOLJET Pro 4 XF-640 User manual
Roland
Roland VersaStudio BT-12 User manual
Roland
Roland CAMM JET CJ-70 User manual
Roland
Roland SP-540i User manual
Roland
Roland TrueVIS SG2-640 Operating manual
Roland
Roland SOLJET Pro III XC-540 User manual
Roland
Roland VS-640 User manual
Roland
Roland VersaUV LEC2-300 User manual
Roland
Roland VersaUV LEC2-300 User manual
Roland
Roland SOLJET PROIII XC-540 User manual
Roland
Roland Color Camm Pro PC-60 User manual
Roland
Roland LEC-300A User manual
Roland
Roland CAMM-1 PNC-1610 User manual
Roland
Roland VersaSTUDIO BN-20D User manual
