Roland VersaCamm SP-300V User manual

1
Before installing, be sure to read this.
This document describes important matters related to installation
operations.When installing, be sure to read this document as well
as the Setup Guide.
The procedures for "Filling with Ink for the First Time" have changed.
Some of what is described in the Setup Guide has changed. The procedure for installing ink cartridges for the
first time after purchase has changed.
➢Use the contents of this document instead of the procedures described on pages 27 to 29 of the Setup
Guide.
➢Careful attention is required,because performing the procedure incorrectly may result in malfunction or
dot drop-out.
➢When filling with ink, use the included dummy cartridges.
Dummy cartridges are included.
Dummy cartridges have been added to the included items.
You use them when filling with ink.
These are also required when moving the machine to a dif-
ferent location, so store them safely, without discarding them.
Important Note When Moving the Machine
When moving the machine to a different location, ink-fill-
ing must be performed again. The dummy cartridges are
needed at this time. Store them safely, without discarding
them.The procedure for moving the machine is described
in the Setup Guide. Note, however, that the ink-filling per-
formed at such times must also be carried out as explained
in this document.
Dummy cartridges

2
Replace pages 27 through 29 of the Setup Guide with this page.
1. Switch on the power and make the initial settings.
➊
Close the front cover.
➋
Switch on the main power switch.
➌
Hold down and press the sub power switch.
➍
Use to select the language you want.
Press .
➎
Use to select the unit of measurement you
want (for length).
Press .
➏
Use to select the unit of measurement you
want (for temperature).
Press .
➐
Make sure the two voltage switches are set correctly.
Press .
ON
LENGTH UNIT
mm mm
TEMP. UNIT
ºC ºC
CHECK HEATER
VOLTAGE SETTING
MENU LANGUAGE
ENGLISH
2. Clean the heads using the cleaning cartridges.
➊
➀Use to select the ink type.
➁Press to enable the selection.
➋
➀Make sure the drain bottle is installed.
➁Press .
➌
Insert cleaning cartridges into slots 1 and 2.
SELECT INK TYPE
E-SOL Max 4 COLOR
SET SOL CL-LIQUID
1 2
Flashing
INSTALL
DRAIN BOTTLE
Cleaning cartridge

3
Replace pages 27 through 29 of the Setup Guide with this page.
➍
➀Insert the dummy cartridges into slots 3 and 4.
➁Press .
➎
Pull out the cleaning cartridges from slots 1 and 2.
➏
➀Pull out the dummy cartridges from slots 3 and 4.
➁Press .
➐
Insert the cleaning cartridges into slots 3 and 4.
➑
➀Insert the dummy cartridges into slots 1 and 2.
➁Press .
FILLING INK...
SET DUMMY CRT.
SLOT: 3, 4
Dummy cartridge
Wait.
Orient with the
round hole facing up.
REMOVE SOL CL
1 2
Flashing
FILLING INK...
Wait.
REMOVE DUMMY CRT
SLOT: 3, 4
SET SOL CL-LIQUID
3 4
Flashing
Cleaning cartridge
Cleaning cartridge
Dummy cartridge
FILLING INK...
SET DUMMY CRT.
SLOT: 1, 2
Gently insert all the way.
Dummy cartridge
Orient with the
round hole facing up.
Gently insert all the way.
Wait.

4
Replace pages 27 through 29 of the Setup Guide with this page.
➒
Pull out the cleaning cartridges from slots 3 and 4.
➓
➀Pull out the dummy cartridges from slots 1 and 2.
➁Press .
3. Insert the ink cartridges for the respective colors.
➊
Before you insert the ink cartridge for each color, gently
shake the cartridge.
➋
Insert the ink cartridge for each color.
➌
When the screen in the figure appears, ink filling ends.
Insert into the slot of the matching color.
BK
1
CY
2
MG
3
Y
E
4
SET SOL CRT.
1 2 3 4
SETUP SHEET
Flashing
FILLING INK...
REMOVE DUMMY CRT
SLOT: 1, 2
SET SOL CRT.
1 2 3 4
Flashing
Wait.
REMOVE SOL CL
3 4
Flashing
FILLING INK...
Wait. Cleaning cartridge
Dummy cartridge
R2-061113