Roland udk20 User manual

Double Sheet Detector
R1000 series UDK20
Electro magnetic and eddy current principles
integrated in one sensor -
microcontroller based
Only one linearized sensor for ferrous and non-ferrous materials
FE materials for sheet thickness up to max. 4 mm (.16 in.)
NF materials for sheet thickness up to max. 4 mm (.16 in.) depending on electrical conductivity
► Direct connection of up to 2 sensors to a unit possible (version 2 PW)
► Programmable for 255 different sheet thicknesses and materials
► Calibration with a teach-in procedure
► Digital display of sheet thickness and operational parameters
► Monitoring of over-gauge and under-gauge limits
► Monitoring of operating voltage and sensor
► Galvanically insulated 9-bit PLC input interface
► Galvanically insulated 4-bit PLC output interface
► Selectable equipment interfaces:
- Data communication and data backup via (optional) potential-free RS232 interface
- Relay outputs or opto-coupler outputs for under-gauge, nominal gauge, over-gauge and enabling
ROLAND
DOUBLE SHEET CONTROL UDK20
>Panel mount enclosure
>All common fieldbus standards
NOW AVAILABLE:

Copyright
© 2011 ROLAND ELECTRONIC GmbH
Otto-Maurer-Str. 17
DE 75210 Keltern
All rights on this document are at Roland Electronic GmbH.
Reproduction (also partly), electronical coverage, translation, transmission to third parties,
only with our prior permission.
Subject to change without further notice.

Manual
Double Sheet Detector R1000 series UDK20
B0048991 / Rev. 1.3 Table of contents
ROLAND ELECTRONIC GmbH · Otto-Maurer-Str. 17 · DE 75210 Keltern · Phone [phone] · Fax [phone]
Declaration of conformity according to EC directives .....................................................................................7
1Safety advices ........................................................................................................................................9
1.1 Declaration of icons...........................................................................................................................9
1.2 Safety instructions and warnings for user .........................................................................................9
1.3 Intended use ...................................................................................................................................10
2Technical data ......................................................................................................................................11
2.1 Technical data control unit UDK20 .................................................................................................11
2.2 Versions of the control unit UDK20.................................................................................................13
2.3 Sensors ...........................................................................................................................................14
2.4 Sensor performance data (Measuring time) for ferrous (FE) material............................................15
2.5 Sensor data for non-ferrous (FE) material ......................................................................................18
2.6 Sensor cables .................................................................................................................................18
3System description ..............................................................................................................................21
3.1 Measurement principle....................................................................................................................21
3.2 General hints for process security ..................................................................................................22
3.3 Control unit......................................................................................................................................23
3.4 Parameters of the control unit.........................................................................................................23
3.5 Application samples ........................................................................................................................28
4Mounting ...............................................................................................................................................33
4.1 General mounting instructions ........................................................................................................33
4.2 Dimensions of the system ...............................................................................................................34
4.3 Mounting of sensors........................................................................................................................38
4.4 Automatic tool changer ...................................................................................................................51
5Electrical installation ...........................................................................................................................52
5.1 General instructions ........................................................................................................................52
5.2 Configuration of connectors ............................................................................................................52
5.3 Connecting diagram - examples .....................................................................................................64
5.4 Internal wiring of the Sensor-Switch-Box SSBUDK10 ....................................................................67
6Communication with the PLC .............................................................................................................68
6.1 PLC inputs.......................................................................................................................................68
6.2 PLC output signals ..........................................................................................................................68
6.3 Timing diagrams..............................................................................................................................69
6.4 Internal control (Demo mode) .........................................................................................................79
7Start-up..................................................................................................................................................80
7.1 Initially applying power to the system .............................................................................................80

Manual
Double Sheet Detector R1000 series UDK20
Table of contents B0048991 / Rev. 1.3
4 ROLAND ELECTRONIC GmbH · Otto-Maurer-Str. 17 · DE 75210 Keltern · Phone [phone] · Fax [phone]
7.2 Operation........................................................................................................................................ 80
7.3 Configuration menu ........................................................................................................................ 81
7.4 General information regarding the configuration............................................................................ 83
7.5 Changing, setting-up or checking the configuration....................................................................... 83
7.6 Program parameters ...................................................................................................................... 84
7.7 System parameters ........................................................................................................................ 90
7.8 Data backup via serial RS232-interface (only for C-versions) ....................................................... 97
8Operation.............................................................................................................................................. 98
8.1 Abbreviated operating instructions................................................................................................. 98
8.2 Entering a measurement program................................................................................................ 100
9Fault messages, causes and remedies ........................................................................................... 101
9.1 Fault messages of the Sensor-Switch-Box .................................................................................. 102
9.2 Fault concerning memory............................................................................................................. 103
9.3 Faults concerning Zero adjust ...................................................................................................... 103
9.4 Faults concerning Teach-In.......................................................................................................... 104
9.5 Faults concerning RS232 Transmission ...................................................................................... 104
9.6 Faults concerning measuring operation ....................................................................................... 104
9.7 Faults concerning keyboard ......................................................................................................... 104
9.8 Faults concerning supply voltage................................................................................................. 105
9.9 Faults Sensor Switch Box ............................................................................................................ 105
9.10 Faults concerning PLC parallel inputs.......................................................................................... 105
9.11 Other faults................................................................................................................................... 105
10 Maintenance....................................................................................................................................... 106
10.1 Replacement of sensors............................................................................................................... 106
10.2 Exchange of control unit............................................................................................................... 108
10.3 Replacement of fuses................................................................................................................... 108
10.4 Data back up via the serial interface ............................................................................................ 109
10.5 Short description RPP-XP software ............................................................................................. 109
10.6 Spare parts................................................................................................................................... 109
11 Technical records.............................................................................................................................. 110
11.1 Exchange of equipment................................................................................................................ 110
12 Order data .......................................................................................................................................... 111
12.1 Versions of control unit UDK20 .................................................................................................... 111
12.2 System accessories ..................................................................................................................... 111
12.3 Sensors and accessories ............................................................................................................. 112
12.4 Cables .......................................................................................................................................... 112

Manual
Double Sheet Detector R1000 series UDK20
B0048991 / Rev. 1.3 Table of contents
ROLAND ELECTRONIC GmbH · Otto-Maurer-Str. 17 · DE 75210 Keltern · Phone [phone] · Fax [phone]
12.5 Cable plugs and cable sockets .....................................................................................................112
12.6 Other accessories .........................................................................................................................112
13 Appendix .............................................................................................................................................113
13.1 System configuration form ............................................................................................................113

Manual
Double Sheet Detector R1000 series UDK20
B0048991 / Rev. 1.3
6 ROLAND ELECTRONIC GmbH · Otto-Maurer-Str. 17 · DE 75210 Keltern · Phone [phone] · Fax [phone]
Pos: 1 /Komponenten allge mein/Leerseite @ 0\mod_1 165223317234_501. doc @ 2343 @ @ 1
Blank page
Pos: 2 /Komponenten allge mein/EG-Konformi tätserklärung 115/230V AC @ 0\mod_1173707333875 _501.doc @ 3827 @ @ 1

Manual
Double Sheet Detector R1000 series UDK20
B0048991 / Rev. 1.3
ROLAND ELECTRONIC GmbH · Otto-Maurer-Str. 17 · DE 75210 Keltern · Phone [phone] · Fax [phone]
Declaration of conformity according to EC directives
Manufacturer: Roland Electronic GmbH
Otto-Maurer-Str. 17
DE 75210 Keltern
Product name: UDK20
Product type: Double Sheet Detector
R1000 series
Roland Electronic GmbH declare that the product listed above complies with the requirements of
the EMC directives listed below.
Applied Directives:
2006/95/EG Directive regarding electrical equipment to be used within specified
voltage levels.
EN61010-1: 2001
2004/108/EU: Generic emission standard;
EN61000-6-2: 2005 EN61000-6-4: 2001
Date of mark’s apposition: 01.08.2009
Keltern, 01.08.2009 Managing Director
Place, Date Signature Function of the signer
The declaration confirms the compliance with the cited directives. However, it is not any implied warranty of fitness for a
particular purpose especially as it may relate to product liability.
The safety instructions and warnings must be observed.
ISO 9001 : 2008
Reg.-no. 5152 QM08
Pos: 3 /Komponenten allge mein/Leerseite @ 0\mod_1 165223317234_501. doc @ 2343 @ @ 1

Manual
Double Sheet Detector R1000 series UDK20
B0048991 / Rev. 1.3
8 ROLAND ELECTRONIC GmbH · Otto-Maurer-Str. 17 · DE 75210 Keltern · Phone [phone] · Fax [phone]
Blank page
Pos: 4 /Kapitelübersic ht/01. Sicherhei tshinweise @ 0\mod_1121421 059859_501.doc @ 505 @ 1 @ 1

Manual
Double Sheet Detector R1000 series UDK20
B0048991 / Rev. 1.3 Safety advices
ROLAND ELECTRONIC GmbH · Otto-Maurer-Str. 17 · DE 75210 Keltern · Phone [phone] · Fax [phone]
1 Safety advices
Pos: 5 /Komponenten allge mein/Symbolerkläru ng @ 0\mod_1139563726296_ 501.doc @ 1549 @ 2 @ 1
1.1 Declaration of icons
Warning - general dangers!
Reference to imminent hazards, which can result in severe bodily harm or death.
Warning - dangers by high voltage!
Reference to imminent hazards due to electricity, which can result in severe bodily
harm or death.
Attention - Damage of construction units!
Reference to a potential imminent situation, which can result in damage to the
product or environs.
Note
Useful reference to an application or deepening information.
Pos: 6 /Komponenten allge mein/Sicherheitshin weise NUR UDK20 @ 2\mod_13 19529720157_501.doc @ 10203 @ 2 @ 1
1.2 Safety instructions and warnings for user
This handbook contains all information required for the correct operation of the Roland equipment.
It has been written for technically qualified personnel.
Unauthorized tampering with the unit, especially ignoring the warnings in this handbook, can cause
malfunction and damage to the unit. Only authorized personnel should be allowed to make
changes to the unit and perform cable connections especially the power supply.
Should it be necessary, e.g. in case of service or repair, to make measurements within the unit,
then all customary accidents prevention procedures should be observed. Only professional
electrical tools should be used.
Note The factory pre-settings – especially the upper / lower limit values – have
been chosen such that an optimal machine protection is ensured.
Diverging settings can impair the machine protection.
Safety advice for persons with cardiac pacemakers!
Persons with cardiac pacemakers are to stay away from the sensors!
The strong magnetic / electromagnetic fields of the sensors can cause malfunction
of cardiac pacemakers and other such apparatus!
Warning When connecting or disconnecting the sensor plug you must stop
measurement!
Non-observance can result in a damage of the sensor!
Pos: 7 /Komponenten allge mein/Symbolerkläru ng @ 0\mod_1139563726296_ 501.doc @ 1549 @ 2 @ 1

Manual
Double Sheet Detector R1000 series UDK20
Safety advices B0048991 / Rev. 1.3
10 ROLAND ELECTRONIC GmbH · Otto-Maurer-Str. 17 · DE 75210 Keltern · Phone [phone] · Fax [phone]
Pos: 8 /Doppelblech/ Geräte/UDK20/1 Sicher heitshinweise/Bes timmungsgemäßer Gebrauc h @ 1\mod_1306408034591_ 501.doc @ 9209 @ 2 @ 1
1.3 Intended use
Flexible Manufacturing Systems in the sheet processing industry require reliable Double Sheet
Control systems in order to protect presses and other sheet processing machines against damage
caused by feeding multiple sheets.
The Double Sheet Detector UDK20 was specifically developed for this technical environment.
Depending on the application (type of material, thickness, sensor gap) the UDK 20 can be used
with up to four sensors. The reliable function of the Double Sheet Detector depends therefore
markedly on the selection of the correct sensors and the mounting of the sensors.
Pos: 9 /Kapitelübersic ht/02. Technische Date n @ 0\mod_1121421119875_5 01.doc @ 506 @ 1 @ 1

Manual
Double Sheet Detector R1000 series UDK20
B0048991 / Rev. 1.3 Technical data
ROLAND ELECTRONIC GmbH · Otto-Maurer-Str. 17 · DE 75210 Keltern · Phone [phone] · Fax [phone]
2 Technical data
Pos: 10 /Doppelblech/ Geräte/UDK20/2 Technisc he Daten/Geräteda ten UDK20 @ 1\mod_13064080993 12_501.doc @ 9215 @ 2 @ 1
2.1 Technical data control unit UDK20
Operating voltage: 24 VDC, +6 V / -2 V
Power consumption: 60 W (operation: <60 W, in idle: <10 W)
Switch on current: 10 Amps for 1 ms
External fuse: 5 Amps medium time lag
Weight: approx. 1.5 kg (3.30 lbs)
Ambient temperature: 0 - 50 °C (30 - 122° F)
Wall mount enclosure:
Protection category: IP65
Dimensions without screw fittings: approx. 205 x 140 x 80 mm (L x W x H)
approx. 8 x 5.5 x 3.15 inch (L x W x H)
Dimensions with screw fittings: approx. 205 x 220 x 80 mm (L x W x H)
approx. 8 x 8.66 x 3.15 inch (L x W x H)
Front panel enclosure:
Protection category: IP40 (inside)
IP65 (front cover)
Dimensions: approx. 180 × 180 × 70 mm (L x W x H)
approx. 7.1 × 7.1 × 3 inch (L x W x H)
Additional characteristics:
• 255 parameter sets memory
• Programming via pushbuttons
• 9 potential free optocoupler inputs 24 VDC with joint common
Specification:
 min. switching voltage HIGH: 13 VDC
 max. switching voltage HIGH: 30 VDC
 min. switching voltage LOW: 0 VDC
 max. switching voltage LOW: 8 VDC
• 4 potential free outputs with positive external supply
Specification relay version:
 Switching outputs Dry relay opening contacts
 max. switching voltage: 250 VAC
 max. switching current: 1 A
 max. switching power: 240 W / 200 VA
Specification opto coupler version:
 Switching outputs unwired Emitter and Collector
 max. switching voltage: 50 VDC
 max. switching current: 150 mA
 max. switching power: 100 mW
Attention In case of inductive load a coil protection diode should be used.
Otherwise the signal output could be destroyed by the excess voltage
generated by switching the inductive load off.

Manual
Double Sheet Detector R1000 series UDK20
Technical data B0048991 / Rev. 1.3
12 ROLAND ELECTRONIC GmbH · Otto-Maurer-Str. 17 · DE 75210 Keltern · Phone [phone] · Fax [phone]
• RS232 interface
Specification:
- Baudrate: 4800
- Data Bits: 8
- Parity-Bit: None
- Stop-Bit: 1
- Hardware Handshake: None
The selection of the interface parameters with the exception of the baudrate is made via the
software and cannot be changed by user.
Pos: 11 /Doppelblech/ Geräte/UDK20/2 Technisc he Daten/Varianten de s Auswertegerätes UDK20 @ 1\mod_1306408103874_5 01.doc @ 9239 @ 2 @ 1

Manual
Double Sheet Detector R1000 series UDK20
B0048991 / Rev. 1.3 Technical data
ROLAND ELECTRONIC GmbH · Otto-Maurer-Str. 17 · DE 75210 Keltern · Phone [phone] · Fax [phone]
2.2 Versions of the control unit UDK20
The control unit article key is coded as follows:
1. Control unit UDK20 for connection of one sensor
BCD E
UDK20 xx---
S
-FP
A = Control unit
B = Version
B
C
C = Outputs
O: Opto coupler
R: Relay
D = Connectors on the unit pluggable
E = Control unit in front panel enclosure
2. Control unit UDK20 for connection of up to four sensors,
all sensors are plug connected directly at the unit.
B
C
D
E
UDK20 xx---
S
-FP-2P
W
F
A = Control unit
B = Connection of up to 2 sensors
C = Version
B
C
D = Outputs
O: Opto coupler
R: Relay
E = Connectors on the unit pluggable
F = Control unit in front panel enclosure
Version B Memory for 255 parameter sets (Nominal thickness and upper and lower limits).
Set up and addressing by push buttons
or via 9 resp. 11 opto coupled data inputs 24 VDC with joint common.
Version C Same as Version B but in addition:
1 opto coupled RS232 interface for bi-directional data communication with a PLC or PC.
Basing on the article key shown above the following versions are available:
Variants of the UDK20 control unit (examples)
With one sensor With up to two sensors
For wall mounting For front panel mounting For wall mounting For front panel mounting
UDK20-B-R-S UDK20-B-R-S-FP UDK20-2PW-B-R-S UDK20-2PW-B-R-S-FP
UDK20-B-O-S UDK20-B-O-S-FP UDK20-2PW-B-O-S UDK20-2PW-B-O-S-FP
UDK20-C-O-S UDK20-C-O-S-FP UDK20-2PW-C-O-S UDK20-2PW-C-O-S-FP
Pos: 12 /Doppelblech/ Geräte/UDK20 Bus/2 Tec hnische Daten/Sensoren @ 1\ mod_1306417693892_50 1.doc @ 9276 @ 2 @ 1

Manual
Double Sheet Detector R1000 series UDK20
Technical data B0048991 / Rev. 1.3
14 ROLAND ELECTRONIC GmbH · Otto-Maurer-Str. 17 · DE 75210 Keltern · Phone [phone] · Fax [phone]
2.3 Sensors
The sensor description has the following code:
W42
A
G
S
A
B
C
DE
F
A = Electro magnet
B = Eddy current
C = Diameter
D = Model
E = Thread
F = Quick disconnect
Fig. 1: Designation of sensors
Pos: 13 /Doppelblech/ Sensoren/PW-Sensor en/PW42AGS/PW42AGS Techn. Daten @ 1\mod_13064141512 37_501.doc @ 9269 @ 3 @ 1
2.3.1 Sensor PW42AGS
PW42AGS PW42AGS PW42AGS
with straight cable plug with 90° angled cable plug
Top View
All dimensions are in mm. Length tolerance ± 0.8 mm, all other dimensions ± 0.2 mm
Fig. 2: Sensor PW42AGS
Technical data
Measuring range 2): 0.2 – 4.0 mm .01 - .16 inch
Ambient temperature: 0 – 60 °C 30 – 140 °F
Class of protection: IP65
Weight: ca. 0.5 kg 1.1 lbs
Sensor cable: pluggable
1) Necessary space for sensor plug connection
2) Related to single sheet thickness
Pos: 14 /Doppelblech/ Geräte/UDK20 Bus/2 Tec hnische Daten/Sensorda ten @ 1\mod_130640810040 6_501.doc @ 9221 @ 22 @ 1

Manual
Double Sheet Detector R1000 series UDK20
B0048991 / Rev. 1.3 Technical data
ROLAND ELECTRONIC GmbH · Otto-Maurer-Str. 17 · DE 75210 Keltern · Phone [phone] · Fax [phone]
2.4 Sensor performance data (Measuring time) for ferrous (FE) material
In the following diagram the response time of the control unit for measurement is shown depending
in number of sensors activated by the program. In addition the response time depends on the
selected system parameter “Measure”, the actual sheet thickness, the nominal sheet thickness
and the upper limit (up).
System parameter „Measure“
• „fast“
The actual response time depends on the measured sheet thickness, the nominal thickness
and the upper limit (up).
The maximum response time is limited by the nominal thickness and the upper limit (see
diagram and example).
Advantage: maximum response time is low.
Disadvantage: In case of measuring results larger than the double sheet threshold, the text
“2-sheet” is issued instead of the actual measurement value.
• „normal“
The actual response time depends on the measured sheet thickness.
The maximum response time corresponds to the maximum sheet thickness.
Example 1:
• System parameter “Measure: fast”
• Measurement with one sensor
• Nominal thickness 1.0 mm = 100%
• upper limit (UP) 120% (=1.2 mm)
Actual sheet thickness = 1 mm actual response time = 58 ms
Actual sheet thickness = 2 x 1 mm actual response time = 62 ms
Actual sheet thickness = 7 x 1 mm (sensor on stack) actual response time = 62 ms
The maximum response time is 62 ms (with “up“ = 120%). This means that after the signal "measurement start" was issued
(max. 30ms), it will take 62 ms until the result of the measurement is available as output signal (with “up“ =120%).
Example 2:
• System parameter “Measure: normal”
• Measurement with one sensor
• Nominal thickness 1.0 mm = 100%
• upper limit (UP) 120% (=1.2 mm)
Actual sheet thickness = 1 mm actual response time = 58 ms
Actual sheet thickness = 2 x 1 mm actual response time = 68 ms
Actual sheet thickness = 7 x 1 mm (sensor on stack) actual response time = 80 ms
The maximum response time is 80 ms (with “up“ = 120%). This means that after the signal "measurement start" was issued
(max. 30ms), it will take 80 ms until the result of the measurement is available as output signal (with “up“ =120%).
Note The advantage in measuring time is significant, if the thickness of material
is considerably lower than the measuring range of the sensor.

Manual
Double Sheet Detector R1000 series UDK20
Technical data B0048991 / Rev. 1.3
16 ROLAND ELECTRONIC GmbH · Otto-Maurer-Str. 17 · DE 75210 Keltern · Phone [phone] · Fax [phone]
The data for 2 sensors apply in the so-called sequencer mode.
Standard working range
Single sheet thickness
(Nominal thickness) [mm]
40
50
60
70
80
90
100
110
120
130
140
150
160
170
2 Sensors
1 Sensor
PW42AGS
150 %
120 %
0,51,01,52,02,5
03,0 3,5 4,0
Fig. 3: System reaction time P42AGS
Double sheet thresholds above 120% reduce the performance of the system with regard to air gaps
between the sheets and increase the systems reaction time according to the diagram.
Air gaps influence the performance negatively because air has - in contrast to steel - a high
resistance to the magnetic flux. Therefore, air gaps reduce the performance of the system
considerably (see chapter “3.1 Measuring principle and conditions influencing measurement
accuray“).
For reliable double sheet monitoring there should be no air gap between sheet and sensor and also
between the sheets. The most reliable double sheet recognition results, if no air gaps exists. These
aspects should be specifically observed when mounting the sensors.
The influence of air gaps are described in the following diagrams.

Manual
Double Sheet Detector R1000 series UDK20
B0048991 / Rev. 1.3 Technical data
ROLAND ELECTRONIC GmbH · Otto-Maurer-Str. 17 · DE 75210 Keltern · Phone [phone] · Fax [phone]
Max. air gap between sensor and first sheet (1st air gap)
0,4
0,6
0,8
1,0
1,2
1,4
1,6
1,8
2,0
2,2
2,4
2,6
2,8
3
,
0
Sheet thickness
[mm]
1
s
t
a
i
r
g
a
p
[
mm
]
1.
12345670,5 1,5 2,5 3,5 4,5 5,5 6,5
PW42AGS
Max. air gap between first and second sheet (2nd air gap)
2
3
4
5
6
7
8
9
10
11
12345670,5 1,5 2,5 3,5 4,5 5,5 6,5
2
n
d
a
i
r
g
a
p
[
mm
]
Sheet thickness
[mm]
2.
PW42AGS
The data apply for a set upper limit of 120%.

Manual
Double Sheet Detector R1000 series UDK20
Technical data B0048991 / Rev. 1.3
18 ROLAND ELECTRONIC GmbH · Otto-Maurer-Str. 17 · DE 75210 Keltern · Phone [phone] · Fax [phone]
2.5 Sensor data for non-ferrous (NF) material
The amount of eddy current generated and the corresponding energy absorption is directly related
to the electrical conductivity. High values of electrical conductivity and the corresponding strong
eddy currents reduce the controllable sheet thickness.
The eddy current principle is more forgiving with regard to air gaps than the electromagnetic
principle.However, for most reliable performance precaution should be taken to avoid air gaps
between sensor and sheet. The permissible air gaps between first and second sheet can be slightly
higher than for steel.
Note The system reaction time for non-ferrous materials is constant at 85 ms.
This applies for measurements with 1 sensor as well as for measurements
with 2 sensors (in sequencer mode).
Material Conductivity (MS) Max. thickness for single sheet (mm)
Austenite 1,41 4,0
Bronze 8,5 4,0
Zinc 16,3 4,0
AL-Alloy 18,2 4,0
AL-Alloy 25,2 4,0
AL 34,2 4,0
CU-Alloy 43 3,5
CU 57,5 3,0
Pos: 15 /Doppelblech/ Geräte/UDK20 Bus/2 Tec hnische Daten/Sensorka bel @ 1\mod_13064081024 68_501.doc @ 9233 @ 2333 @ 1
2.6 Sensor cables
Suitable cable type:
• Superflex (C)Y PURKOMBI 2 x 1,0 mm² + 4 x 2 x 0,25 mm²
• The cable is oil-proof and suitable for drag chains
- Bending radius flexible use min. 110 mm
Cable marking:
• for PW42AGS:
SCPWS-GG (straight receptacle at the sensor)
SCPWS-GW (right angle receptacle at the sensor)
The cable have quick disconnects at both ends. The plug at the control unit side is always straight.
Note The sensor cable is an active component of the sensor technology. The
technical data of the sensors is valid only if the cable specification is met. A
shielded cable (2 x 1,0 mm² + 4 x 2 x 0,25 mm²) must be used. The cable
length can be to up to 50 m. Following the rule "the shorter the better"
generally leads to better measuring results.

Manual
Double Sheet Detector R1000 series UDK20
B0048991 / Rev. 1.3 Technical data
ROLAND ELECTRONIC GmbH · Otto-Maurer-Str. 17 · DE 75210 Keltern · Phone [phone] · Fax [phone]
2.6.1 Sensor cable SCPWS for PW42AGS sensor
Cable socket, sensor side Cable plug, unit side
3
45
6
7
81
9
54
26 24
3
45
6
7
81
9
Socket contacts Plug contacts
Right angle cable socket, sensor side
60
1 grey
2 pink
3 red
4 black / violet
5 blue
6 brown 1 mm²
7 brown
8 white 1 mm²
9 green
Enclosure blank (Shield)
Fig. 4: Sensor cable SCPWS
to Sensor to control unit
Cable socket Bootlace ferrules
pink
red
black
violet
blue
brown *
white *
brown
green
1
2
3
4
5
6
8
7
9
PW42AGS
1
2
3
4
5
6
8
7
9
1
2
3
4
5
6
8
7
9
1
2
3
4
5
6
8
7
9
1 grey
2 pink
3 red
4 black / violet
5 blue
6 brown 1 mm²
8 white 1 mm²
7 brown
9 green
Enclosure blank (Shield)
Cable types for the sensor PW42AGS (order data):
• SCPWS-GG (straight receptacle at the sensor)
• SCPWS-GW (right angle receptacle at the sensor)
The standard length is 5 meter. Cable length up to 50 meter made to order, longer cables please
enquire.
Note In particular with larger lengths the sensor cable should not be placed
directly adjacent to cables with large noise potential.
The cable is drag cable suitable and oil resistant.
Cable type:
• Superflex (C)Y PURKOMBI 2 x 1,0 mm² + 4 x 2 x 0,25 mm²

Manual
Double Sheet Detector R1000 series UDK20
Technical data B0048991 / Rev. 1.3
20 ROLAND ELECTRONIC GmbH · Otto-Maurer-Str. 17 · DE 75210 Keltern · Phone [phone] · Fax [phone]
2.6.2 Sensor cable extensions
A sensor cable extension can be relatively easy made. For this a SCPWS-GG or SCPWS-GW
cable is always needed.
2.6.3 Cable for Sensor-Switch-Box SSBUDK10
The cable SVCPWS-SSBUDK10 is used for connecting the control unit to the Sensor Switch Box.
The following pin configuration and dimensions apply:
to Sensor-Switch-Box to unit
Cable socket Cable plug
2
3
5
4
51
22 22
2
3
5
4
1 white
2 green
3 brown
4 yellow
5 grey
Enclosure blank (Shield)
1 white
2 green
3 brown
4 yellow
5 grey
Enclosure blank (Shield)
to Sensor-Switch-Box to unit
Cable socket Cable plug
1
2
3
4
5
grey
white
brown
green
yellow
SSBUDK10
1
2
3
5
4
1
2
3
5
4
1 white
2 green
3 brown
4 yellow
5 grey
Enclosure blank (Shield)
Cable type for SSBUDK10 (order data):
• SVCPWS-SSBUDK10
The standard length is 5 meter.
Note For the connection of the SSBUDK10 to the sensor PW42AGS the
SCPWSGG or SCPWS-GW are used.
Pos: 16 /Komponenten allge mein/Leerseite @ 0\ mod_1165223317234_501. doc @ 2343 @ @ 1
Pos: 17 /Kapitelübersic ht/03. Systembesc hreibung @ 0\mod_112142115 0062_501.doc @ 507 @ 1 @ 1