rollease acmeda KLIP User manual

KLIP & STEIN
INSTALLATION MANUAL

CONTENTS
DISCLAIMER
INTRODUCTION
This Installation manual has been produced by Rollease Acmeda to supply the necessary information for safe and correct installation of the awning.
DISCLAIMER
Rollease Acmeda has used reasonable care in preparing the information included in this document, but makes no representations or warranties as to the
completeness or accuracy of the information. Information is supplied upon the condition that the persons receiving the information will make their own
determination as to its suitability for their purposes prior to use. Rollease Acmeda assumes no liability whatsoever for any damages incurred by you resulting from
errors in or omissions from the information included herein. Rollease Acmeda reserves the right to make changes without further notice to any products to improve
reliability, function or design.
COPYRIGHT
COPYRIGHT © ROLLEASE ACMEDA
All rights are reserved. No part of this document may be reproduced or utilised in any means, by any means, electronic or mechanical including photocopying,
recordings, or by any information storage or retrieval system, without the express permission from Rollease Acmeda.
SECTION 1 | WARRANTY
3
SECTION 2 | PRIOR TO INSTALLATION
4
SECTION 3 | INSTALLATION
5
QUANTITY OF BRACKETS REQUIRED ...........................................................................................................5
INSTALLATION ..... .................................................................................................................................................7
COUPLED AWNINGS ...................................................................................................................................11
KLIP XL VERSION. ...............................................................................................................................................17
ARM ASSEMBLY... ...............................................................................................................................................18
HOOD ASSEMBLY. ...............................................................................................................................................21

Page. 3
KLIP & STEIN AWNING Product Spec Manual | v 1.0
2020 ©Copyright All Rights Reserved Rollease Acmeda
WARRANTY
Rollease Acmeda provide a 5 year hardware warranty against defects to the original purchaser [the fabricator/manufacturer].
The hardware warranty is not to be transferred to the end consumer.
The hardware warranty is limited to the repair or resupply of defective hardware components to the fabricator/manufacturer only.
The hardware warranty is applicable to normal use.
The hardware warranty when applied to external systems assumes the blinds are not used in strong winds/storms and not left down indefinitely.
The hardware warranty will not apply where the defect arises due to incorrect assembly and installation.
The hardware warranty is not applicable for coastal applications unless specified.
Retailers are obliged to supply consumers with their own warranty, if required, at the point of purchase.
SECTION 1 | WARRANTY

Page. 4 KLIP & STEIN AWNING Installation Manual | v 1.0
2020 ©Copyright All Rights Reserved Rollease Acmeda
SECTION 2 | PRIOR TO INSTALLATION
INSTALLERS RESPONSIBILITY
SAFETY INFORMATION
Before installing, please read & ensure you understand the safety information and installation instructions as de-
fined in this installation manual.
• If you do not fully understand these instructions, contact Rollease Acmeda for clarification before installing.
• The Installer is responsible to ensure that all installation personnel have been adequately trained on the safe &
correct installation and operation.
• The Installer is reponsible to ensure that a Job Safety Analysis or Safe Work Method Statement is completed
prior to intallation to identify hazards, to determine appropriate risk control measures and to implemenent the
control measures.
• The Installer is responsible to ensure that supporting structures are sound and can adequately support the
load.
• The Installer is responsible to ensure that the devises used to anchor the product to the supporting structure
are suitable for the application.
• Ensure Job Safety Analysis/Safe Work Method Statement is completed and actions to reduce risks are imple-
mented.
• Ensure that electrical works are done only by a LICENSED ELECTRICIAN.
• DO NOT modify any of the componenets of this system.
• Only suitable trained/qualified personal shoud undertake installation.

Page. 5
KLIP & STEIN AWNING Product Spec Manual | v 1.0
2020 ©Copyright All Rights Reserved Rollease Acmeda
QUANTITY OF BRACKETS REQUIRED
SECTION 3 | INSTALLATION
QUANTITY OF BRACKETS ACCORDING TO WIDTH AND PROJECTION
WIDTH 240-300 301-360 361-410 411-480 481-540 541-600* 601-700* 701-800* 801-900** 901-1100** 1101-1400***
ARMS 2 3 4 6
PROJECTION
165 2 3 3 3 4 4 7 8 8 9 12 215 2 3 3 3 4 4 7 8 8 9 12 265 3 3 4 4 4 7 8 8 9 12 315 4 4 5 5 7 8 8 9 12 365 4 5 5 7 8 8 9 12
KLIP XL VERSION ONLY
415 - - - 4 5 5 7 8 8 9 12
NOTE:
* 1 Support Compensator ** 2 Support Compensators *** 3 Support Compensators

Page. 6 KLIP & STEIN AWNING Installation Manual | v 1.0
2020 ©Copyright All Rights Reserved Rollease Acmeda
QUANTITY OF BRACKETS REQUIRED
SECTION 3 | INSTALLATION
QUANTITY OF BRACKETS ACCORDING TO WIDTH AND PROJECTION
Brackets must be positioned within the hatched areas; outer brackets must be at a minimum distance of 40mm
from edge of the square bar (not red hatching).

Page. 7
KLIP & STEIN AWNING Product Spec Manual | v 1.0
2020 ©Copyright All Rights Reserved Rollease Acmeda
INSTALLATION
SECTION 3 | INSTALLATION
CORRECT BRACKETS POSITION
BRACKET ALIGNMENT
NOTE:
• Position and quantity of brackets depend on the awning width and projection.
• The brackets must be positioned within the hatched areas.
NOTE:
• Ensure brackets are correctly aligned in all directions.

Page. 8 KLIP & STEIN AWNING Installation Manual | v 1.0
2020 ©Copyright All Rights Reserved Rollease Acmeda
INSTALLATION
SECTION 3 | INSTALLATION
INSTALL SQUARE BAR
SECURE SQUARE BAR
NOTE:
• Locate the square bar into the mounting brackets.
WARNING:
• DO NOT overtighten the fixing screws

Page. 9
KLIP & STEIN AWNING Product Spec Manual | v 1.0
2020 ©Copyright All Rights Reserved Rollease Acmeda
INSTALLATION
SECTION 3 | INSTALLATION
FITTING CAPS TO BRACKETS
CHECK OPERATION
NOTE:
• After checking that the awning is secure, cover the brackets with the caps.
NOTE:
• Open and close the awning to check correct operation.

Page. 10 KLIP & STEIN AWNING Installation Manual | v 1.0
2020 ©Copyright All Rights Reserved Rollease Acmeda
ADJUSTING THE AWNING
SECTION 3 | INSTALLATION
PITCH ADJUSTMENT
ADJUSTING ARM ALIGNMENT
NOTE:
• Ensure the awning is extended 300mm - 600mm from the inner limit to provide access to the grub screw.
• Loosen the side screw [1] of the arm support (10mm Allen Key).
• Tighten the socket-head cap screw [2] to lift the arms (8mm Allen Key).
Always support the weight of the arms when adjusting the awning.
• Loosen the socket-head cap screw [2] to lower the arms.
• After adjustment, check that the terminal bar is horizontal.
• When terminal bar is horizontal, firmly secure the side screw [1].
NOTE:
• After adjusting the awning pitch, check that the arms are parallel when the awning is closed.
• If they are not parallel, extend the awning 300mm - 600mm to access the grub screw [1]
• While supporting the weight of the awning arms, tighten or loosen the grub screw [1] (3mm Allen Key) to adjust
the arm alignment.
Tightening lifts the arm, loosening lowers the arm.

Page. 11
KLIP & STEIN AWNING Product Spec Manual | v 1.0
2020 ©Copyright All Rights Reserved Rollease Acmeda
COUPLED AWNINGS
SECTION 3 | INSTALLATION
WARNING:
• DO NOT remove the arm lock.
ARM COUPLING
NOTE:
• In some cases, arms must be coupled with the arm support.
• Fit the arm on the lever by inserting the pin.

Page. 12 KLIP & STEIN AWNING Installation Manual | v 1.0
2020 ©Copyright All Rights Reserved Rollease Acmeda
COUPLED VERSION
SECTION 3 | INSTALLATION
ROLLER TUBE COUPLING
FABRIC ASSEMBLY
NOTE:
• Couple the tube with the supplied tube joiner kit.
NOTE:
• Slide the fabric into the tube, centre it, lock it and roll it up.

Page. 13
KLIP & STEIN AWNING Product Spec Manual | v 1.0
2020 ©Copyright All Rights Reserved Rollease Acmeda
COUPLED VERSION
SECTION 3 | INSTALLATION
SQUARE BAR ASSEMBLY
TUBE ASSEMBLY WITH FABRIC
NOTE:
• Fit the brackets considering the position of arm supports and centre balance supports.
• Fit the square bar inserting it on the pre-assembled joint and secure it.
NOTE:
• Insert the tube with the rolled up fabric into the square bar roller supports. First insert the side of the cap with
hole into the plate with pin, then the motor side, having pre-assembled the nuts if required. Secure the latter to
the roller support with the screws provided.

Page. 14 KLIP & STEIN AWNING Installation Manual | v 1.0
2020 ©Copyright All Rights Reserved Rollease Acmeda
COUPLED VERSION
SECTION 3 | INSTALLATION
CENTRE BALANCE SUPPORTS ASSEMBLY
TERMINAL PROFILE COUPLING
NOTE:
• Install the centre supports in line with fabric joins.
NOTE:
• Couple the terminal bar by inserting it on the pre-assembled joint and secure with the rivets provided.
• Fit the arm stoppers and the terminal bar connecting plates onto the terminal bar.

Page. 15
KLIP & STEIN AWNING Product Spec Manual | v 1.0
2020 ©Copyright All Rights Reserved Rollease Acmeda
COUPLED VERSION
SECTION 3 | INSTALLATION
TERMINAL BAR ASSEMBLY
ARMS/TERMINAL BAR FIXING
NOTE:
• Assemble the terminal bar sliding the fabric into the relevant keyway.
• Centre the terminal bar with the fabric.
NOTE:
• Fix the arms to the terminal bar keeping them parallel to the square bar and tightening the M8x16 countersunk
screws on the previously fitted plates.
• Remove the arm lock only after having fixed the terminal bar connecting screws.

Page. 16 KLIP & STEIN AWNING Installation Manual | v 1.0
2020 ©Copyright All Rights Reserved Rollease Acmeda
COUPLED VERSION
SECTION 3 | INSTALLATION
AWNING ADJUSTMENT
NOTE:
• Place the arm stoppers properly.
• Open and close the awning; after checking that arms and fabric are perfectly aligned, fix the fabric to the termi-
nal profile.
• Fit the end caps onto the terminal bar.
• Adjust the awning as described previously in the non-coupled version; also adjust the angle of the centre bal-
ance supports.

Page. 17
KLIP & STEIN AWNING Product Spec Manual | v 1.0
2020 ©Copyright All Rights Reserved Rollease Acmeda
KLIP XL VERSION
SECTION 3 | INSTALLATION
NOTE:
• Fit the brackets within the hatched areas; outer
brackets at a minimum distance of 40mm from the
edge of the square bar (not the red hatching).

Page. 18 KLIP & STEIN AWNING Installation Manual | v 1.0
2020 ©Copyright All Rights Reserved Rollease Acmeda
ARM ASSEMBLY
SECTION 3 | INSTALLATION
ARM ASSEMBLY
AWNING ADJUSTMENT
NOTE:
• If arm assembly is required, place the plastic cam on the arm shoulder, fit it onto the lever and couple it with
the pin.
NOTE:
• Remove the arm support cap [1] rotating it downwards.
• Loosen the screw [2] (3mm Allen Key)
21

Page. 19
KLIP & STEIN AWNING Product Spec Manual | v 1.0
2020 ©Copyright All Rights Reserved Rollease Acmeda
ARM ASSEMBLY
SECTION 3 | INSTALLATION
AWNING ADJUSTMENT
AWNING ADJUSTMENT
NOTE:
• Ensure the awning is extended 300mm - 600mm to provide access to the socket head cap screw.
• Adjust the arm angle by adjusting the socket head cap screw [3] of the arm support (8mm Allen Key).
• Tighten the socket-head cap screw [3] to lift the arm (8mm Allen Key)
Always support the weight of the arms when adjusting the awning.
• Loosen the socket-head cap screw [3] to lower the arm.
• After adjustment, check that the terminal bar is perfectly horizontal.
NOTE:
• After adjustment, secure by firmly tightening the screw [4] (3mm Allen Key).
• Fit the cap [5] again, first by hooking it to the lower part, then clip in the top part.
3
5
4

Page. 20 KLIP & STEIN AWNING Installation Manual | v 1.0
2020 ©Copyright All Rights Reserved Rollease Acmeda
ARM ASSEMBLY
SECTION 3 | INSTALLATION
AWNING ADJUSTMENT
NOTE:
• Ensure the arms are parallel when the awning is closed.
• If they are not parallel, extend the awning 300mm - 600mm to provide access to the arm support.
• Tighten or loosen [6] (8mm Allen Key) to adjust the arms alignment, support the arms.
Once the proper position has been set, lock the screw [7] securing the dowel located on the upper part of the
arm support (3mm Allen Key]
•
Always support the weight of the arms when adjusting the awning.
7
6