rollease acmeda KUMO User manual

KUMO
Installation manual

INDEX
1 - INTRODUCTION page 2
1.1 - Symbols used in the manual page 2
1.2 - Personnel requirements page 2
1.3 - Assembly and installation equipment page 3
1.4 - Before starting installation page 3
2 - SAFETY page 4
2.1 - General safety information page 4
3 - KUMO COMPONENTS AND DIAGRAMS page 6
3.1 - Tilting diagrams page 6
4 - KUMO TECHNICAL SHEET page 7
4.1 - Tilting diagrams page 7
5 - INTALLATION KUMO page 8

2IKUMOI INSTALLATION –REV 00
1 –INTRODUCTION
This “assembly manual” for KUMO awnings has been produced by ROLLEASE ACMEDA to supply the
indications necessary for the operations of assembling the components that make up the product.
Assembly must be carried out by personnel with suitable technical and professional qualifications, in
accordance with the respective national laws or regulations (see Par. 1.2 “Personnel requirements”).
It is forbidden to eliminate, rewrite or alter the pages in the manual and their content.
This manual must be kept intact in all its parts, in an easily accessible place.
ROLLEASE ACMEDA reserves the right to update the production and the respective manuals, without
being obliged to update the previous production andmanuals.
ROLLEASE ACMEDA reserves all rights to this manual: no total or partial reproduction is allowed without
authorisation in writing.
1.1 - Symbols used in the manual
Shown below are the WARNING symbols used in this manual:
Indications and advice to be observed to ensure a correct use of the awning. Failure to follow these
indications may endanger the integrity and/or resistance of the product.
DANGER FOR THE OPERATOR! Instructions and indications to be assessed and followed with care.
Failure to follow these indications may endanger personal safety.
1.2 - Personnel requirements
The personnel appointed to perform this operation must possess a technical knowledge of the product,
acquired by assembling similar products for at least one year or after having followed a suitable technical
training course.
IMPORTANT
ATTENTION

3I KUMO I INSTALLATION –REV 00
1.2- Assembly and installation equipment
To ensure the correct assembly of the mechanical part, of the textile part, and consequently the optimum
operation of the finished product, it is necessary to be in possession of the following equipment:
»»complete set of tools;
»»equipment for working at heights (trestles, ladders, scaffolding, overhead platforms, etc.) complying with
current occupational safety regulations;
»»rawlplugs;
»»spirit level;
»»string.
1.3- Before starting
Some components must be cut to suit the dimensions of the awning that is to be obtained (see Par.
3.3 “Table of cutting dimensions”).
IMPORTANT

4IKUMOI INSTALLATION –REV 00
2 –SAFETY
2.1 - General safety information
Follow these safety precautions:
Wear the garments and personal protection equipment contemplated by the safety regulations in force
for the workplace (protective helmet, gloves, etc.).
It is forbidden to use the awning to support yourself: risk of serious personal injury and of damage to
the awning itself.
Do not lay objects on the awning.
This manual is an integral part of the product. Before assembly, carefully read all the instructions given
in this manual.
ROLLEASE ACMEDA guarantees the EC marking only for products supplied by the company itself. If
any parts have to be replaced with other components not guaranteed by ROLLEASE ACMEDA, the
product guarantee will automatically become void and ROLLEASE ACMEDA shall not answer for any
malfunctions of the product.
Some awning components are constantly subject to strong pressure (arms) and, if the instructions in
this manual are not carefully followed, these components may cause serious harm to persons, animals
and things.
Make sure that the temporary equipment used (trestles, scaffolding, ladders, etc.) and all the personal
protective equipment (harnesses, safety belts, etc.) are regulatory and in good condition before using
them.
If the awning must be mounted on a floor higher than the ground floor, cordon off the area and make
sure no-one remains under the awning when lifting it.
ATTENTION
ATTENTION
IMPORTANT
IMPORTANT
IMPORTANT
ATTENTION
ATTENTION
ATTENTION

5I KUMO I INSTALLATION –REV 00
All handling and lifting operations must be carried out with the greatest of care, making sure that all
personnel not involved keep at a safe distance; no-one must remain under suspended loads, whether
still or moving.
As regards personal safety, installation must be performed in observance of Decree of the President of
the Republic 164/56 and Legislative Decree 494/96.
During the operations described in this manual, make sure that ONLY qualified personnel enter the
work area (see Para. 1.2 “Personnel requirements”).
If the awning is installed on a floor higher than the ground floor, the person cleaning the awning must
pay greater attention to the risk of falling.
If a ladder is required during installation, make sure that it is firmly placed on the ground in order to
prevent it from tipping and causing serious injury to the people involved in installation operations.
Make sure there are no people, animals and objects nearby when the awning opens and closes.
ATTENTION
ATTENTION
IMPORTANT
ATTENTION
ATTENTION
ATTENTION

6IKUMOI INSTALLATION –REV 00
3 - KUMO COMPONENTS AND DIAGRAMS
3.1 Tilting diagrams
Awning dimensions with arms folded
Wall mounting
Awning dimensions with arms folded
Roof mounting

7I KUMO I INSTALLATION –REV 00
4 - KUMO Technical sheet
Fixing bracket

8IKUMOI INSTALLATION –REV 00
5 –Intallation Kumo
Brackets position for Kumo on the wall
Brackets position for Kumo on the ceiling
Define the distance of the brackets and position them on the awning assembly frame.
L is the with of the awning
Use anchors M10, or at most M12
Define the distance of the brackets and position them on the awning assembly frame.
L is the with of the awning
Use anchors M10, or at most M12

9I KUMO I INSTALLATION –REV 00
Insert the plates
Kumo for ceiling
ATTENTION: After attaching the brackets insert the plates in the slot in the supports
ATTENTION: For roof-mounted awnings, the support must be fitted vertically and the square nut
inserted in the slot at the top

10IKUMOI INSTALLATION –REV 00
Kumo for wall
Kumo for wall
Install the awning on the brackets fixed to the wall
ATTENTION: Block the awning with the screws

11 I KUMO I INSTALLATION –REV 00
Regulating the awning
Regulating the awning
ATTENTION: Ensure that there are no persons, animals or things in the vicinity while opening/clos-
ing the awning.
Open the awning
ATTENTION: Regulating the awning:
slacken the side screw (see ref. 1 ), (Allen wrench 10). To increase the inclination slacken the
socket-head screw (Allen wrench 6) (see ref. 2). To decrease the inclination tighten the socket-
head screw, raising the terminal bar. After regulation, check that the terminal bar is perfectly
horizontal. ATTENTION: After regulation, firmly tighten the side screw

Regulating the awning
ATTENTION: With the awning almost closed, check that the arms are parallel to the cassette.
If they are not parallel, tighten or slacken the dowel in the lever (Allen wrench 3), accompanying the
arm.