ROOMS TO GO 78-159 User manual

A.- (1) HEADBOARD
B.- (1) FOOTBOARD
C.- (1) LEFT SIDE RAIL
D.- (1) RIGHT SIDE RAIL
E.- (1) WOOD CENTER SUPPORT
F.- (1) SUPPORT
G.- (4) SLATS
H.- (4) 5/16"-18 X 80MM FLAT HEAD BOLTS
I.- (4) 5/16"-18 X 5/8" CROSS DOWEL NUTS
J.- (1) 5MM ALLEN WRENCH
K.- (4) 5/16"-18 X 60MM FLAT HEAD BOLTS
L.- (8) 1 1/4" SCREWS
1.- BEFORE YOU START, CAREFULLY UNPACK AND IDENTIFY EACH COMPONENT AND PIECE OF HARDWARE TO MAKE SURE YOU HAVE EVERYTHING YOU NEED FOR
ASSEMBLY.
2.- ASSEMBLE SLEIGH BED, USING ONE HEADBOARD (A), ONE FOOTBOARD (B), ONE LEFT SIDE RAIL (C) AND ONE RIGHT SIDE RAIL (D).
3.- INSERT TWO DOWEL NUTS (I) INTO THE LEFT AND RIGHT SIDE RAIL ONLY ONE SIDE,SEE THE HOLES, MAKE SURE THE GROOVE IS HORIZONTAL, SEE FIG.3
4.- ATTACH THE SIDE RAIL INTO THE HEADBOARD ( A ), INSERTING TWO 80MM FLAT HEAD BOLTS ( H ) IN THE BACK HOLES OF HEADBOARD, ALIGNED WITH THE
HOLES OF SIDE RAIL, USE THE 5MM ALLEN WRENCH (J) TO TIGHTEN BOLTS, SEE FIG.4
5.- LATER, ATTACH SIDE RAIL IN THE FOOTBOARD, ALIGN THE SIDE RAIL HOLES WITH THE FOOTBOARD HOLES, INSERTING TWO 60MM FLAT HEAD BOLTS (K), ( FIG.A )
USING 5MM ALLEN WRENCH (J) TO TIGHTEN ALL BOLTS, SEE FIG.4
6.- TURN AROUND, WOOD CENTER SUPPORT ( E ) UPSIDE DOWN, INSERT THE SCREW BOLT INSTALLED IN THE SUPPORT ( F ), TO TIGHTEN THE OPOSSITE
OF CLOCKWISE (FIG.B), THEN PLACED THE WOOD SUPPORT, FIRST IN SLOT OF FOOTBOARD AND THEN IN SLOT OF HEADBOARD, SEE FIG.5
TOOLS NEEDED
PHILLIPS HEAD SCREWDRIVER ( NOT INCLUDED )
SLEIGH BED ASSEMBLY INSTRUCTIONS ( 78-159,78-161 )
LIST OF CONTENTS
SLEIGH BED HEADBOARD BOX (78-159,78-161) FIG.1
PLEASE CONTACT YOUR RETAIL STORE WITH SERVICE OR PARTS REPLACEMENT REQUEST
PLATFORM BED FOOTBOARD BOX (78-112,78-113) FIG.2
HARDWARE PACK
(HPK00105)
5MM ALLEN WRENCH ( INCLUDED )
THANK YOU FOR YOUR PURCHASE !
RECLAIM COLLECTION
YES,
HORIZONTAL GROOVE
NO
A
D
G
E
FIG.1
MAKE SURE ALL BOLTS ARE
TIGHTENED COMPLETELY
FIG.2
F
FIG.3
C
B
TO ASSEMBLE THIS SLEIGH BED REQUIRES
TWO PERSONS
I
H
HARDWARE PACK
HPK00105
J
K
L
FIG.4
FIG.A
REV 01 19/09/2016
PAGE 1 OF 2
KIS01133

7.- PLACE FOUR SLATS ( G) ON SIDE RAIL CLEATS, ONE SLAT IN BOTH HDBD & FTBD ENDS, PUSH THE SLATS AGAINST THE BED END POST ( FIG. C ), TWO SLATS
IN THE MIDDLE AT EQUAL DISTANCE FROM THE END SLATS, THEN EACH SLAT MUST BE FASTEN WITH ONE 1 1/4" SCREW (L), SEE FIG.6
2.- USE THE SHORT END OF THE ALLEN WRENCH FOR FINAL TIGHTENING.
TIPS : SEE ILLUSTRATION BELOW
1.- USE THE LONG END OF THE ALLEN WRENCH (J) TO FASTEN BOLTS LOOSELY
AND QUICKLY.
TIPS # 2
TIPS # 1
FIG.B
FIG.5
WARNING:
THE BED SLATS WILL NO SUPPORT A
MATTRESS ALONE,A SLAT PACK OR A
BUNKIE BOARD IS REQUIRED FOR
PROPER SAFETY.
( NOT INCLUDED )
FIG.6 FIG.C
QUEEN SLEIGH BED
78-159 QUEEN SLEIGH BED HEADBOARD
78-112 QUEEN PLATFORM FOOTBOARD
KING SLEIGH BED
78-161 KING SLEIGH BED HEADBOARD
78-113 KING PLATFORM FOOTBOARD
REV 01 19/09/2016
PAGE 2 OF 2
KIS01133