ROOMS TO GO A136-18 User manual

ASSEMBLY
INSTRUCTION
DUAL POWER RECLINER
WITH
BLUETOOTH
SPEAKER
Manufactured
for
Rooms
To
o
HLVN
A
136
/
A
1360
HLVN
SKU
:
A
136
-
18
15515604
A
1360
-
18
11513606
LIST OF PARTS
NO. Description Item Qu ntity
A Backrest 1
B Seat 1
CWall plug
transformer 1
DSpeaker Wall plug
transformer 1

ASSEMBLY INSTRUCTIONS
Step
1
:
Take
out
carefully
the
back
cushions
&
seat
from
the
packing
.
Step 2: Positing the female metal receiver brackets over the male metal posts. Push down the female
brackets over male posts simultaneously until each side is locked into place an audile "click" is heard.
POWER CONNECTION
Step 3: Lift velcro flap located at the bottom back. Latch male wire plug from backrest (headrest motor wire) to
female wire receiver located at the bottom back underneath the flap. This instruction is applicable to all power
headrest. Allow sufficient space between recliner and the wall behind it.
Step 4: Connect wall plug transformer to transformer switch.
And connect transformer plug to electrical outlet.

Step 5: Bluetooth speaker power connection.
With seat cushion facing down, connect female plug on chair and male plug on transformer.
And connect transformer plug to electrical outlet.
ELECTRICAL CONTROLS
1 Press button to recline the recliner to desired position
2 Press button to raise the recliner to the upright position.
3 Press button to activate the headrest forward.
4 Press button to return headrest to the closed position.

BLUETOOTH CONTROLS
NOTE: Have your Bluetooth device (phone, tablet, mp3 player, etc.) turned on before starting.
1 Press the POWER button. Button will glow red.
2 Press and hold the POWER button. The other buttons will glow blue. The Power button will blink red.
This indicates the system is searching for an available Bluetooth signal.
3 Tap the settings button on the phone, tablet, mp3 player etc. Tap on the Bluetooth setting. When your
device finds the chair system the name will appear on your device as eMOMO Remo1.
The chair will give a signal sound to indicate the pairing was successful.
4 Lightly press the POWER button to begin play or stop of an audio file.
5 Press the POWER button for 2 seconds to turn the system off.

WARNINGS
*
Keep
unit
at
least
6
"
from
wall
.
*
Keep
unit
at
least
24
"
from
all
heat
sources
.
* Avoid placing unit in areas where unit can be exposed to direct sunlight other powerful light sources, as
fading or discoloration may occur.
*
Do
not
reach
under
seat
when
mechanism
is
operating
or
serious
injury
may
occur
.
*
Reclining
mechanism
should
only
be
operated
while
seated
properly
.
*
Do
not
sit
on
arms
or
backrest
.
*
Do
not
jump
or
roughhouse
on
furniture
.
*
If
unit
must
be
moved
,
do
not
drag
.
Unit
must
be
lifted
in
order
to
be
moved
.
* Do not continuously operate mechanism for more than one minute or unit may go into protection mode by
shutting down to prevent overheating.
*
Unplug
unit
from
power
source
prior
to
cleaning
mechanism
.
*
Do
not
allow
electrical
components
to
come
into
contact
with
any
liquids
.

CARE AND CLEANING
* Upholstered furniture is packaged tightly to protect it during transsit. This packaging can sometimes cause
creases or misshaped cushions when the furniture comes out of the packaging. These issues will correct
themselves over time as the fibers of the cushions are exposed to air. However, shaping the cushions with
your hands can alleviate the creases and compressed fibers more quickly.
* Use a vacuum cleaner to remove dust and debris from seams and crevasses.
* Use a soft damp cloth to gently clean soiled areas and wipe clean. Do not rub.
* Do not use household cleaners or solvents. Such cleaners may cause damage and/or discoloration.
* Do regularly use dedicated leather care product onto the leather furniture to prevent built up of body oils.
TROUBLE SHOOTING
PROBLEM SOLUTION
Headrest not working Ensure that wall power outlet is functional Step 4
Ensure that headrest power cable is plugged into the seat cable Step 3
Not Reclining Ensure that wall power outlet is opterational Step 4
Speaker not working Ensure the speaker's plug connection and wall power outlet is fuctional Step 5
Backrests gaps Ensure the backrests are properly clipped into the male posts located on seat
mechanism. Check that brackets are not loose, positioned improperly or bent.