ROOMS TO GO KIDS CREEKSIDE 2.0 3934440P User manual

WARNING DANGER
Failure to follow these warnings and assembly instructions could result in serious
injury or death. To help prevent serious or fatal injuries from entrapment or falls:
-
Read all instructions before assembling bunk bed and keep these instructions for future reference.
-
Before each usage or assembly, inspect bunk bed for damaged hardware, loose joints, missing
parts, or sharp edges. DO NOT Use bunk bed if any parts are missing or broken.
-
DO NOT Use substitute parts. Contact your local Rooms To Go or visit www.ROOMSTOGO.COM
for replacement parts and instructional literature if needed.
-
Follow the information on the warnings appearing on the upper bunk end structure and on the carton,
DO NOT REMOVE WARNING LABEL FROM BED.
-
Always use the recommended size mattress or mattress supports, or both to help prevent the likelihood
of entrapment or falls.
-Ensure thickness of mattress and foundation combine does not exceed
10 inches (255mm
) and
mattress surface is at least
5 inches (127mm)
below upper edge of guardrails.
-
Do not allow children under 6 years of age to use the upper bunk.
-
Periodically check and ensure that the guardrail, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
-
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
-
Limit top bunk use to one person.
-
Always use the ladder for entering and leaving the upper bunk.
-
Use of night light may provide added safety precaution for a child using the upper bunk.
-
Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed next to
the wall, the guardrail that runs the full length of the bed should be placed against the wall to
prevent entrapment between the bed and wall.
-
The use of water or sleep flotation mattress is prohibited.
-
This bunk bed meets all the requirements of ASTM 1427-19.
STRANGULATION HAZARD:
Never attach or hang items to any part of the bunk bed that are not designed for
use with the bed; for example, but not limited to, hooks, belts, and jump ropes.
CREEKSIDE 2.0 COLLECTION
THANK YOU FOR YOUR PURCHASE
11/7/2022 Page 1 of 63

36040400 40G-711 LOFT CHEST
4 PC RAILS(2 GUARD & 2 SIDE RAILS)
LOFT CHEST
LOFT CHEST
LOFT BOOKSHELF
LOFT BOOKSHELF
LADDER
FULL/FULL SLAT PACK
FOLDING DESK (Add on)
TOOLS NEEDED
4 Pcs
1" Dry wall Screws
40B-760
36240416
36740416 40B-732
36040412 40B-711
40B-601
35940407 40G-703 FULL TOP BUNKBED END
36740404 40G-732 4 PC RAILS(2 GUARD & 2 SIDE RAILS)
P A R T S L I S T
3934440P FULL LOFT W/ 2 CHESTS & 2 BOOKCASES CHARCOAL
RTG SKU # STYLE # ITEM DESCRIPTION
35940407 40G-703 FULL TOP BUNKBED END
36340406 40G-760 LOFT BOOKSHELF
36340406 40G-760 LOFT BOOKSHELF
36040400 40G-711 LOFT CHEST
3934441P FULL LOFT W/ 2 CHESTS & 2 BOOKCASES CHARCOAL
35940419 40B-703 FULL TOP BUNKBED END
35940419
36440408 40G-721 LADDER
38300238 100-648 FULL/FULL SLAT PACK
36240404 40G-601 FOLDING DESK (Add on)
Phillips screwdriver (not included)
5/16"-18 x 3 3/8" Bolt
Allen wrench (included)
40B-703 FULL TOP BUNKBED END
36440410 40B-721
38300238 100-648
36040412 40B-711
36340418 40B-760
36340418
PARTS LIST QTY PARTS LIST QTY HARDWARE LIST QTY
Full top bunk bed end
1 Pc
22 Pc Ladder 5 mm Hex key
12 Pc
61 Pc
16 Pcs
16 Pcs
4 Pcs
5 Drw Loft chest
3/8" x 3 1/8" Metal
pin
82 Pc
72 Pc
Side rails 6 x 1 1/4"
Drywall screw
Folding desk (Add on)
1 Pc
56 Pcs
Loft Bookshelf Ladder Hook
11/7/2022 Page 51 of 63
6 x 1 1/4"
Drywall screw
Guardrails
32 Pc
4 Pc
4
Full slats
FOLDING DESK HARDWARE
2 Pcs
A
B
C
D
E
C
F

CASES ON THE RIGHT CASES ON THE LEFT
RIGHT SIDE CASES
LEFT SIDE CASES
Remove fastening board and save for next step.
ASSEMBLY INSTRUCTIONS
For Right remove center molding by lifting up then pulling out, then
One for right side and one for left, side align both pieces and tight completely as shown.
11/7/2022 Page 52 of 63
Assemble bookshelf and chest, using the fastening board and bolts previously removed, align one chest and one bookshelf.
remove third drawer, for Left remove center molding and open the door.
STEP 3
STEP 2 B
B
STEP 1
B

11/7/2022 Page 53 of 63
then fasten with 1 1/4" screws. MAKE SURE ALL BOLTS ARE TIGHTENED COMPLETELY
Screw ladder hooks to pre-drilled holes on top of ladder. Screw ladder to guardrail as shown.
ASSEMBLY INSTRUCTIONS
Assemble 2 sets of loft chest, loft bookshelf and top bunk bed ends. Assemble top side rails.
Install slats, one on each end, two equally spaced in the middle, Assemble guardrails and tighten all bolts.
STEP 5
STEP 6
F
STEP 4
B
STEP 7
A
A
A
A
D
D
D
D
B
A
B
A
A
A
A
A
C
C
F
F
EE
STEP 8
STEP 9
E
E
E
E

Twin size mattress- 74" - 75" long and 37-1/2" - 38-1/2" wide
Twin size Bunkie board- 74" long and 37-1/2" wide
Full size mattress- 74" - 75" long and 52-1/2" - 53-1/2" wide
Full size Bunkie board- 74" long and 52-1/2" wide
ASSEMBLY INSTRUCTIONS
11/7/2022 Page 54 of 63
Use only correct mattress dimensions and Bunkie board:
PLEASE CONTACT YOUR RETAIL STORE WITH SERVICE OR PARTS REPLACEMENT REQUEST
Place Bunkie boards (required, sold separately) on top of the slats
STEP 10

then push down
11/7/2022 Page 55 of 63
Remove center molding by lifting up then pulling out Unfold desk leg and look for hardware pack inside desk box.
Secure each corner block with 1 1/4" screw
Unfold corner supports (from desk box hardware pack) in the pre-bore hole.
Place folding desk by sliding into the opening of loft chest
ASSEMBLY INSTRUCTIONS
STEP 11
STEP 13
STEP 12
STEP 14
STEP 15
C
C