Rosslare MD-W11N User manual

MD-W11
Wireless Access Control Door
Interface
Installation Manual
MD-W11BPMD-W11FMD-W11N

Copyright © 2014 by Rosslare. All rights reserved.
This manual and the information contained herein are proprietary to ROSSLARE
ENTERPRISES LIMITED and/or its related companies and/or subsidiaries’
(hereafter: "ROSSLARE"). Only ROSSLARE and its customers have the right to
use the information.
No part of this manual may be re-produced or transmitted in any form or by any
means, electronic or mechanical, for any purpose, without the express written
permission of ROSSLARE.
ROSSLARE owns patents and patent applications, trademarks, copyrights, or
other intellectual property rights covering the subject matter in this manual.
TEXTS, IMAGES, AND ILLUSTRATIONS INCLUDING THEIR ARRANGEMENT IN
THIS DOCUMENT ARE SUBJECT TO THE PROTECTION OF COPYRIGHT LAWS
AND OTHER LEGAL RIGHTS WORLDWIDE. THEIR USE, REPRODUCTION, AND
TRANSMITTAL TO THIRD PARTIES WITHOUT EXPRESS WRITTEN PERMISSION
MAY RESULT IN LEGAL PROCEEDINGS.
The furnishing of this manual to any party does not give that party or any third
party any license to these patents, trademarks, copyrights or other intellectual
property rights, except as expressly provided in any written agreement of
ROSSLARE.
ROSSLARE reserves the right to revise and change this document at any time,
without being obliged to announce such revisions or changes beforehand or
after the fact.

Table of Contents
MD-W11 Installation Manual iii
Table of Contents
1. Introduction ................................................................8
1.1 Overview ................................................................................ 8
1.2 Features.................................................................................. 9
2. Technical Specifications............................................10
2.1 Supported Card Transmission Formats.................................... 11
2.2 Supported Keypad Transmission Formats................................ 11
2.3 Available Models................................................................... 12
3. Installation and Wiring .............................................13
3.1 The Installation Kit ................................................................ 13
3.2 General Installation Requirements .......................................... 14
3.3 Installing the MD-W11N Unit................................................. 14
3.4 Wiring the MD-W11N Unit .................................................... 15
3.5 Installing the MD-W11F Unit.................................................. 18
3.6 Wiring the MD-W11F Unit..................................................... 19
3.7 Installing the MD-W11BP Battery Pack.................................... 20
3.8 Wiring the MD-W11BP Battery Pack....................................... 20
3.9 Indications on the Near and Far Units ..................................... 20
3.10 Installer Recommendations .................................................... 21
4. Enrollment.................................................................22
4.1 Enrolling the Units................................................................. 22
4.2 DIP Switches ......................................................................... 22
4.2.1 Near and Far Unit Modes ..............................................................23
5. Operational Information ..........................................26
A. Declaration of Conformity........................................27

Table of Contents
iv MD-W11 Installation Manual
B. Limited Warranty ......................................................28

List of Figures
MD-W11 Installation Manual v
List of Figures
Figure 1: MD-W11 Interface ..............................................................................8
Figure 2: MD-W11 Back Cover ........................................................................14
Figure 3: Near Unit Wiring Diagram.................................................................15
Figure 4: Sample Wiring Detail ........................................................................17
Figure 5: Far Unit Wiring Diagram ...................................................................19
Figure 6: LED Display Panel..............................................................................20

List of Tables
vi MD-W11 Installation Manual
List of Tables
Table 1: DIP Switch Settings ............................................................................22
Table 2: Unit Channels Setting ........................................................................23

Notice and Disclaimer
MD-W11 Installation Manual vii
Notice and Disclaimer
This manual’s sole purpose is to assist installers and/or users in the safe and
efficient installation and usage of the system and/or product described herein.
BEFORE ATTEMPTING TO INSTALL AND/OR USE THE SYSTEM,THE INSTALLER AND THE
USER MUST READ THIS MANUAL AND BECOME FAMILIAR WITH ALL SAFETY
REQUIREMENTS AND OPERATING PROCEDURES.
The system must not be used for purposes other than those for which it
was designed.
The use of the software associated with the system and/or product, if
applicable, is subject to the terms of the license provided as part of the
purchase documents.
ROSSLARE exclusive warranty and liability is limited to the warranty and
liability statement provided in an appendix at the end of this document.
This manual describes the maximum configuration of the system with the
maximum number of functions, including future options. Therefore, not all
functions described in this manual may be available in the specific system
and/or product configuration you purchased.
Incorrect operation or installation, or failure of the user to effectively
maintain the system, relieves the manufacturer (and seller) from all or any
responsibility for consequent noncompliance, damage, or injury.
The text, images and graphics contained in the manual are for the purpose
of illustration and reference only.
All data contained herein is subject to change without prior notice.
In no event shall manufacturer be liable for any special, direct, indirect,
incidental, consequential, exemplary or punitive damages (including,
without limitation, any and all damages from business interruption, loss of
profits or revenue, cost of capital or loss of use of any property or capital or
injury).
All graphics in this manual are for reference only, some deviation between
the image(s) and the actual product may occur.
All wiring diagrams are intended for reference only, the photograph or
graphic of the PCB(s) are intended for clearer illustration and
understanding of the product and may differ from the actual PCB(s).

Introduction
8 MD-W11 Installation Manual
1. Introduction
1.1 Overview
The MD-W11 Wireless Access Control Door Interface is a quick and
inexpensive solution for connecting remote door devices, such as
readers, locks, and Request-for-Exit (REX) buttons to an access control
unit.
The MD-W11 consists of two units per door – one located near the
controller (the Near Unit) and the other near the door (the Far Unit)
(Figure 1).
Figure 1: MD-W11 Interface
Near Unit Far Unit Battery Pack
The Near Unit is connected to a Rosslare door controller (such as AC-
215, AC-225, or AC-525). The Far Unit is connected to proximity card
readers or keypads (such as AY-K12 and AY-Q64B).
When a card is read or a code is entered by keypad, the Far Unit
transmits the information to the Near Unit. The Near Unit, attached to
the controller, determines whether or not to open the door. The
controller then sends the message to the Near Unit, which transmits it
to the Far Unit, and if authorized, the door is opened.
Changes or modifications to this equipment not expressly
approved by the party responsible for compliance (Rosslare)
could void the user’s authority to operate the equipment.

Introduction
MD-W11 Installation Manual 9
1.2 Features
The MD-W11 Wireless Access Control Door Interface includes:
Bi-directional RF data communication
Supports PIN codes and card formats, such as Wiegand 26-Bit,
Wiegand 32-Bit, and Wiegand 6-Bit Rosslare formats (see
Section 2.1).
Lock and door relay commands
Tamper, door monitor, and REX messages between the controller
and the interface unit
Rolling code to increase security
Four different RF channels to prevent collisions
Built-in charger for up to 12 VDC, 7 Ah backup battery on the Far
Unit
Transfers proximity card information and LED control, reader
tamper, lock relay commands, REX, and door monitor events
between the coupled units.
Optional MD-W11BP battery pack housing with space for 12
VDC, 800 mAh, sealed lead-acid battery.
Suitable for indoor use.
Available in 869 MHz (H) and 433.92 MHz (G) bands
The Near Unit is powered from the controller's power supply. The
Far Unit is powered by a local wall transformer. A built-in charger
provides battery backup.

Technical Specifications
10 MD-W11 Installation Manual
2. Technical Specifications
Electrical Characteristics
Input Voltage Far Unit: 12–24 AC, 15–24 VDC
Near Unit: 13.8 VDC from the controller's power supply
or wall adapter
Battery Charger 12 V sealed Lead-Acid, up to 7 Ah (Far Unit)
Input Current Standby: 70 mAh
Max: 160 mA
Maximum Range:
(with external
antenna)
Open field: 300 m (985 ft)
Range depends on RF related environmental conditions.
Response Time Up to 500 ms with Rosslare’s AC-215 controller and
reader
Response time depends on RF link quality, number of
doors used, and controller and reader response time.
Output Relays Far Unit: One 5 A Form C relay
Near Unit: Two 1A Form C relays
Output Types Far Unit: LED CTRL – open collector
Near Unit: STAM, SPV, LBAT, AC, TMP – open collector
Communications Bi-directional RF, narrow band
Fast anti-collision, rolling code protocol with data
protection
Available in 4 bands (see Section
4.2)
Data Transfer Reader formats (based on the card and keypad
transmission formats listed below), lock commands,
REX, door monitor, LED control and reader tamper
inputs
Supervisory &
Alerts
Full supervision over the remote unit. Alert outputs at
the Near Unit for supervision failure, system tamper,
reader tamper, low battery and power failure.

Technical Specifications
MD-W11 Installation Manual 11
Environmental Characteristics
Operating
Environment
Indoor use
Operating
Temperature Range
-10°C to 50°C (14°F to 122°F)
Operating Humidity
Range
0 to 95% (non-condensing)
Dimensions
H x W x D Near/Far Units:
13 x 8.7 x 3.2 cm (5.1 x 3.42 x 1.26 in.)
Battery Pack:
12.8 x 6.9 x 3.4 cm (5.04 x 2.72 x 1.34 in.)
Weight Near/Far Units: 155 g (5.5 oz)
Battery Pack (with battery): 433 g (15.3 oz)
2.1 Supported Card Transmission Formats
Wiegand 26-Bit (default)
Wiegand 26-Bit with Facility Code Output
Wiegand 32-Bit
Wiegand 32-Bit Reverse Output
Wiegand 34-Bit
Wiegand 40-Bit
2.2 Supported Keypad Transmission Formats
Single Key, Wiegand 6-Bit (Rosslare format, default)
Single Key, Wiegand 6-Bit with Nibble and Parity bits
Single Key, Wiegand 8-Bit, Nibble Complemented
4 Keys Binary, Wiegand 26-Bit
1 to 5 Keys, Wiegand 26-Bit
6 Keys BCD and Parity Bits, Wiegand 26-Bit

Technical Specifications
12 MD-W11 Installation Manual
2.3 Available Models
MD-W11NHR (869 MHz)
MD-W11FHR (869 MHz)
MD-W11NGR (433 MHz)
MD-W11FGR (433 MHz)
MD-W11BP

Installation and Wiring
MD-W11 Installation Manual 13
3. Installation and Wiring
The Near and Far Units of the MD-W11 are installed and wired as
explained in this chapter.
3.1 The Installation Kit
The installation kit of the MD-W11 interface includes:
MD-W11N Near Unit
The Near Unit sends the controller the proximity card ID or
keypad code as though it were a local reader. Following controller
code/ID verification, the lock relay receives a command
(transmitted to the Far Unit) to open the door.
MD-W11F Far Unit
The Far Unit is connected to a proximity card reader and/or
keypad, and controls the door lock relay.
MD-W11BP Battery Pack
The battery pack is mounted only on the MD-W11 Far Unit side
(see Section 3.7).
The MD-W11N and the MD-W11F are connected to the controller
and the door components (lock, door monitor, reader). Both units are
transceivers; the Near Unit receives the data transmitted from the
reader and sends it to the controller. If authorized, the controller
sends authorization to the Near Unit, which transmits authorization to
the Far Unit. The Far Unit then opens the door.
The wireless access control door interface transfers the data between
the controller input, the outputs, and the door components (such as
lock, reader, door monitor, and exit button) transparent, as if the door
components were connected directly to the controller.

Installation and Wiring
14 MD-W11 Installation Manual
3.2 General Installation Requirements
The installation kit includes:
One drilling template (label /sticker)
One security spline key
One security hex screw
Four mounting screws
Four wall plugs
Fixed external antenna (G Model)
3.3 Installing the MD-W11N Unit
The Near Unit can be connected to a standard Rosslare controller,
such as the AC-225.
To install the Near Unit:
1. Use the spline key to remove the case security screw from the
back of the unit (Figure 2).
Figure 2: MD-W11 Back Cover
A

Installation and Wiring
MD-W11 Installation Manual 15
2. Use the drilling template to determine where to drill holes in the
wall.
3. Use the hardware to mount the back plate on the wall.
We highly recommend using the bottom left mounting hole, as
it is acts as a back tamper when a person attempts to dislodge
the unit from the wall (see Figure 2 marked with A).
4. Wire the unit as instructed in Section 3.4.
3.4 Wiring the MD-W11N Unit
Wire the following terminals between the controller's input and
output to the MD-W11N Near Unit, as shown in Figure 3:
Figure 3: Near Unit Wiring Diagram

Installation and Wiring
16 MD-W11 Installation Manual
Power supply connections (+12V and GND)
STAM – System tamper
SPV – Supervision failure (Far Unit has supervision failure)
LBAT – Low battery (Far Unit has low battery)
AC Fail – Far Unit has power failure
D0 – Data 0
D1 – Data 1
LED – Reader LED control
TMP – Far Reader tamper
LOCK – Connection for lock input
Relay 1 REX (output)
Relay 2-Door monitor (output)
•System Tamper (STAM), Supervision Failure (SPV), Low Battery
(LBAT), AC FAIL (AC) are outputs that can be connected to any
input of AC-225. In AxTraxNG, this input should be configured
accordingly (using Panel Links).
•If either the far reader, the near reader, or both have been
tampered with, the STAM status changes, and retains this status
until both readers have been closed.

Installation and Wiring
MD-W11 Installation Manual 17
Figure 4: Sample Wiring Detail
Figure 4 shows sample input connections to any inputs, and is
relevant to AC-215/225/525.
The relevant input can be configured to result in the required
outcome, using AxTrax and Panel Links.
•The connection between the REX Input and Rel
ay 1 is always COM+
N.O. or COM+N.C. so that only two lines connect to this pair.
•The connection between the Door Monitor Input and Relay 2 is
always COM+N.O. or COM+N.C. so that only two lines connect to
this pair.

Installation and Wiring
18 MD-W11 Installation Manual
3.5 Installing the MD-W11F Unit
The Far Unit can be connected to a standard Rosslare reader, such as
the AY-K12. The optional battery box can then be attached to the
wall next to the Far Unit.
To install the Far Unit:
1. Attach the battery box to the wall with two screws.
2. Insert the wires from the reader and from the battery to the hole
in the side of the Far Unit box.
3. Attach the side of the unit box to the wall with four screws.
4. Attach the wires to the PCB.
5. Cover both the battery and the Far Unit boxes.
6. Tighten the screws on the bottom of both boxes so that they
remain closed.
7. Wire the unit as instructed in Section 3.6.

Installation and Wiring
MD-W11 Installation Manual 19
3.6 Wiring the MD-W11F Unit
Wire the following terminals between the controller's input and
output to the Far Unit, as shown in Figure 5:
Figure 5: Far Unit Wiring Diagram
12–24 VAC or 15–24 VDC to the VIN+ and VIN-
Optional backup battery that connects to BAT+ and BAT-
12 V and GND power output for the reader
Data 0 Wiegand (D0) (input)
Data 1 Wiegand (D1) (input)
LED – Reader LED control (output)

Installation and Wiring
20 MD-W11 Installation Manual
TMP – Input for receiving reader tamper alert
Normally Open (NO)/Normally Closed (NC) and COM of 5A Form
C relay to the door’s lock
REX – Optional input for REX
DM – Optional input for door monitor contact
3.7 Installing the MD-W11BP Battery Pack
Only install the MD-W11BP battery pack in the MD-W11 Far Unit.
To install the battery pack:
1. Use the spline key to remove the security screw from the bottom
of the case and open the unit.
2. Use the drilling template to locate where to drill holes in the wall.
3. Use the hardware provided to mount the back plate on the wall.
4. Wire the battery pack as described in Section 3.8.
The battery pack comes with a battery installed. The size of the
case is compatible with Rosslare’s BT-05 12 VDC/800 mA SLA
rechargeable battery.
3.8 Wiring the MD-W11BP Battery Pack
In the Far Unit only, connect the Red (+) and Black (GND) to MDW11F
Bat (+) and Bat (-) (Figure 5)
3.9 Indications on the Near and Far Units
Figure 6 shows the six LEDs (that indicate the unit’s current status) on
the display panel of each unit.
Figure 6: LED Display Panel
PWR – Power ON
Tx – Sending transmission