Rosslare KE-30 User manual

KE-30
Battery Operated Two-Way Wireless Keypad
Installation Manual
1
1. Introduction
The KE-30 is a wireless keypad for use with Rosslare wireless panels. The
KE-30 features include:
Fully featured keypad, including: LED indicators, function buttons
(arm-away, arm-home, disarm), numeric pad, buzzer, and emergency
triggering.
RFID proximity reader for arming and disarming. The range varies
according to the type of card used, and is up to a maximum of
2.5 cm.
LED indications of the system status, including: Alarm in Memory,
Trouble and Bypass, and system status (armed away/armed
home/disarmed).
Wall keypad tamper-protection mechanism.
Low-power consumption; its internal batteries are designed to last
for years, under normal operation.
Figure 1: KE-30 Wireless Keypad
2. Technical Specifications
2.1 Electrical Characteristics
Power Supply Voltage 4 batteries – CR123A 3 V, 1300 mAh
Current Consumption Standby – 17 uA; Transmit – 14 mA
Battery Life 1 year
2.2 Environmental Characteristics
Operating Environment Indoor use
Operating Temperature Range -10°C to 50°C (14°F to 122°F)
Operating Humidity Range 0 to 95% (non-condensing)
2.3 Physical Characteristics
RFID Proximity Reader Read-compatible with Wiegand 26-bit
EM4102 card (or compatible standard)
Read Range Maximum of 2.5 cm (using Rosslare's AT-
R14)
Frequencies G – 433.92 MHz
H – 868.35 MHz
Dimensions (H x W x D) 140 x 100 x 28 mm (5.5 x 3.9 x 1.1 in.)
Weight 99 g (0.2 lb)
Standards FCC, CE, EN 50131-3, EN 50131-6, EN
50130-5, EN 50130-4, Security Grade 2,
Environmental Class II
3. Install the KE-30
3.1 Mounting the KE-30
To mount the keypad on the wall:
1. Locate and release the screws at the bottom of the keypad, and
open the cover.
2. Place the back plate at the desired location. The keypad should be
installed at eye level.
3. Use the dimensions given in Figure 2 or use the back cover as a
template.
4. Drill four holes in the wall and insert the anchors provided.
5. Mount and fasten the back plate with the screws provided, and
assure that the back plate is level.
6. Secure the back plate with the screws referred to in Step 1.
Figure 2: Mounting Dimensions
3.2 Replacing the Batteries
To replace the CR123A batteries:
1. Open the cover (Figure 3)
2. Remove the used batteries and replace them.
3. Close the cover and the system is up and running.
Figure 3: Battery Placement
3.3 Enrolling the Keypad
Please refer to the keypad enrolling section of the HomeLogiX™wireless
panel manual or refer to any Rosslare wireless panel manual that
supports the relevant keypad.
3.4 Enrolling Proximity Cards
Please refer to the proximity card enrolling section of the HomeLogiX
wireless panel manual or refer to any Rosslare wireless panel manual that
supports the relevant proximity cards.
Only up to two RFID cards can be enrolled in a panel.

2
4. Tamper
The KE-30 is secured to the wall with a screw (see Section 3.1). Tamper
control is implemented via a knock-out hole when the KE-30 is
installed. Any attempt to tamper with the system sets off an alarm.
Figure 4: Tamper Knock-Out
5. Utilizing the KE-30 Wireless Keypad
The KE-30 functions as both an Arming/Disarming unit and as a Status
Viewing unit.
5.1 Arm/Disarm and Basic Operations
The following subsections describe how to arm the system using the
various options.
5.1.1 Basic Arming using the Keypad
1. Press the ARM AWAY key and enter the user code.
The system beeps and the ARM AWAY LED indicator flashes.
2. Press the ARM HOME key and enter the user code.
The system beeps and the ARM HOME LED indicator flashes.
3. Press the DISARM key and enter the user code.
The DISARM LED indicator flashes.
5.1.2 QUICK AWAY and QUICK HOME Functions
1. Press the AWAY button for 2 seconds.
The system beeps and is armed AWAY.
2. Press the HOME button for 2 seconds.
The system beeps and is armed HOME.
5.1.3 Emergency Alarm Activation
1. Press 1and 3simultaneously for 3 seconds to activate the
emergency alarm.
5.2 Status Viewing
The Arm Home LED indicator, the Arm Away LED indicator, and
the Disarm LED indicator flash, but they do not remain on
continuously.
The KE-30 indicates a panel's status by flashing the relevant LED
indicator, and displays one of the following statuses:
Armed Away
Armed Home
Disarmed
In Memory and Trouble
Bypass
When a new KE-30 unit is turned on, a flashing Trouble LED indicator
indicates that the unit must be enrolled. Once it has been enrolled, the
Disarm LED indicator flashes.
If the system is experiencing trouble, the Trouble LED indicator (!)
flashes.
If there is an alarm in memory in the system, the Alarm LED indicator
(M) flashes.
If the system is bypassed, the Bypass LED indicator (Z) flashes.
5.3 RFID Function
The RFID function is deactivated by default, since if it is
activated, battery life is significantly shortened.
5.3.1 Enabling the RFID Function
1. Press both *and #for 3 seconds until the system beeps twice.
2. After the system beeps twice, press 1, and then press #.
When the RFID is activated, the system beeps once.
5.3.2 Cancelling the RFID Function
1. Press both *and #for 3 seconds until the system beeps twice.
2. After the system beeps twice, press 0and then press #.
The RFID is now deactivated.
5.3.3 Enrolling Proximity Cards
Please refer to the Proximity Card Enrolling section of the HomeLogiX
wireless panel manual or refer to any Rosslare wireless panel manual
that supports the relevant proximity cards.
To use a proximity card to arm or disarm the system:
1. Activate the RFID function.
2. Press on the Away, Home, or Disarm button
3. Place the card directly above the keypad.
The system activates the desired function (Arm Away/Home or
Disarm).
Changes or modifications to this equipment not expressly
approved by the party responsible for compliance (Rosslare
Ltd.) could void the user’s authority to operate the equipment.

3
Limited Warranty
The full ROSSLARE Limited Warranty Statement is available in the Quick
Links section on the ROSSLARE website at www.rosslaresecurity.com.
Rosslare considers any use of this product as agreement to the
Warranty Terms even if you do not review them.
Contact Information
United States and Canada
Rosslare Security Products, Inc.
Southlake, TX, USA
Toll Free: [phone]
Local: [phone]
Fax: [phone]
[e-mail]
Europe
Rosslare Israel Ltd.
Rosh HaAyin, Israel
Tel: [phone]
Fax: [phone]
[e-mail]
Latin America
Rosslare Latin America
Buenos Aires, Argentina
Tel: [phone]
[e-mail]
China
Rosslare Electronics (Shenzhen) Ltd.
Shenzhen, China
Tel: [phone]
Fax: [phone]
[e-mail]
Asia Pacific, Middle East, Africa
Rosslare Enterprises Ltd.
Kowloon Bay, Hong Kong
Tel: [phone]
Fax: [phone]
[e-mail]
India
Rosslare Electronics India Pvt Ltd.
Tel/Fax: [phone]
Mobile: [phone]
[e-mail]
www.rosslaresecurity.com
0706-0960254+03