SECO-LARM Enforcer SK-1323-SDQ Operating instructions

NOTE: Products with a model number that ends with “Q” or have a round green “Q” sticker represent RoHs compliant products.
Quick User Programming Guide
Outdoor Stand-Alone
Weatherproof Keypads
Model
Number
2 Relay
Outputs
Backlit
Keys
Proximity
Reader
SK-2323-SDQ


SK-2323-SPQ



SK-1323-SDQ


SK-1323-SPQ



Sealed-Environment Keypads
Mullion-Style Keypads
(SK-2323-SDQ shown)
For complete programming instructions, please see page 10 of the User Manual.
(SK-1323-SPQ shown)

ENFORCER Outdoor Stand-Alone Keypads Quick Programming Guide
2SECO-LARM U.S.A., Inc.
Program new Master Code immediately.
Program the Output #1 access mode immediately, or the keypad will only accept
user cards.
Take note of the keypad status LEDs—
oRight LED Green: Standby
oLeft LED Solid Red/Right LED Solid Orange: Programming Mode
oRight LED Flashing Orange: Awaiting code/card entry
If unsure of which mode the keypad is in, press until the right LED is green.
The keypad is now in the standby mode. Enter the master code twice to return to
Programming Mode.
For complete programming instructions, see page 10 of the User Manual.
Programming Tips
*SK-2323-SPQ and SK-1323-SPQ only.
Setting the Output #1 Access Mode*
DEFAULT: User card only. To use codes, you MUST set mode to or .
2. Enter .
0
0
0
User card ONLY (DEFAULT)
Either user card OR user code
0
1
Note: The Output #1 Access Mode must be programmed in order for the
SK-2323-SPQ and SK-1323-SPQ to accept user codes.
3. Enter one of the following:
0
2
User card AND user code
1. Enter Programming Mode by entering the Master Code twice.
4. Exit Programming Mode by pressing .
1. Enter Programming Mode by entering the Master Code twice.
(Default Master Code is 12345)
2. Enter .
3. Enter the new 5-digit Master Code twice.
Programming the Master Code
3
Example: If the desired new Master Code is 54321, enter:
5
4
3
2
1
5
4
3
2
1
4. Exit Programming Mode by pressing .
0
1
0
2

ENFORCER Outdoor Stand-Alone Keypad Quick Programming Guide
SECO-LARM U.S.A., Inc 3
2. Enter a user ID number.
Programming Output #1
*SK-2323-SPQ and SK-1323-SPQ only.
Each Output #1 user can be programmed to have a user code and a user card.*
1.3 User Card and Code*
7. Exit Programming Mode by pressing .
4. Swipe a new user card.
2. Enter a user ID number.
6. To program the next user, repeat from step 2 in section 1.1, 1.2, or 1.3.
5. Enter a new 5-digit user code.
1. Enter Programming Mode by entering the Master Code twice.
3. If the left LED is red, previous user data exists. Clear it by entering .
The keypad will beep in confirmation and the left LED will turn green.
2. Enter a user ID number.
1. Enter Programming Mode by entering the Master Code twice.
1.1 User Code Only
4. Enter a new 5-digit user code.
5. To program the next user, repeat from step 2 in section 1.1, 1.2, or 1.3.
6. Exit Programming Mode by pressing .
( to )
0
0
0
9
9
9
3. If the left LED is red, previous user data exists. Clear it by entering .
The keypad will beep in confirmation and the left LED will turn green.
7. Exit Programming Mode by pressing again.
5. Return to Programming Mode by pressing .
4. Swipe a new user card.
6. To program the next user, repeat from step 2 in section 1.1, 1.2, or 1.3.
1. Enter Programming Mode by entering the Master Code twice.
1.2 User Card Only*
3. If the left LED is red, previous user data exists. Clear it by entering .
The keypad will beep in confirmation and the left LED will turn green.
( to )
0
0
0
9
9
9
( to )
0
0
0
9
9
9

ENFORCER Outdoor Stand-Alone Keypads Quick Programming Guide
4SECO-LARM U.S.A., Inc.
Programming Output #2
NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy
is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without notice.
SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2010 SECO-LARM U.S A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part, without
the written permission of SECO-LARM.
SK-x323-SxQ Addendum_1008.docx
PICCN2
SECO-LARM®U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com
Tel: [phone] Fax: [phone] E-mail: i[email protected]m
*SK-2323-SPQ and SK-1323-SPQ only.
8. Exit Programming Mode by pressing again .
5. Enter a new 5-digit user code.
2.1 Programming an Output #2 User Code
3. Enter a user ID number.
6. To program the next user, repeat from step 3 in section 2.1 or 2.2.
7. Return to Programming Mode by pressing .
2. Enter .
4
1. Enter Programming Mode by entering the Master Code twice.
4. If the left LED is red, previous user data exists. Clear it by entering .
The keypad will beep in confirmation and the left LED will turn green.
( to )
0
0
0
9
8. Exit Programming Mode by pressing again.
5. Swipe a new user card.
2.2 Programming an Output #2 User Card*
3. Enter a user ID number.
6. To program the next user, repeat from step 3 in section 2.1 or 2.2.
7. Return to Programming Mode by pressing .
2. Enter .
4
1. Enter Programming Mode by entering the Master Code twice.
4. If the left LED is red, previous user data exists. Clear it by entering .
The keypad will beep in confirmation and the left LED will turn green.
( to )
0
0
0
9
Each Output #2 user may only have a user code OR a user card programmed.