rough country 31007 User manual

Thank you for choosing Rough Country for all your vehicle needs.
Please read instructions before beginning installation. Check the kit hardware against the kit contents shown below. Be
sure you have all needed parts and know where they go.
If question exist, please call us @1-800-222-7023. We will be happy to answer any questions concerning this product.
Check all fasteners for proper torque. Check to ensure for adequate clearance between all components.
Check and retighten wheels at 50 miles and again at 500 miles. Periodically check all hardware for tightness.
Rough Country LED lights are for off-road use only.
If factory equipped, winch bumper may interfere with parking, proximity and external cruise control sensors.
KIT CONTENTS:
1-EXO Front Bumper W/ Light mount
2– 2” Flush Mount LED Cubes
1– Single Row 20” LED
1– Drivers Side Frame Bracket
1– Passengers Side Frame Bracket
2-D-rings
TOOLS NEEDED:
18mm wrench or socket
19mm wrench and socket
Ratchet
HARDWARE INCLUDED:
2-12mm x 120mm Bolts
4-1/2” x 3 1/2” Bolts
10-1/2” Flat Washers
2-1/2” Lock Washers
4-1/2” Nylock Nuts
4-12mm x 35mm Bolts
4-12mm Flat Washers
4-12mm Lock Nuts
Torque Specs:
Size Grade 5 Grade 8 Size Class 8.8 Class 10.9
5/16” 15 ft/lbs 20ft/lbs 6MM 5ft/lbs 9ft/lbs
3/8” 30 ft/lbs 35ft/lbs 8MM 18ft/lbs 23ft/lbs
7/16” 45 ft/lbs 60ft/lbs 10MM 32ft/lbs 45ft/lbs
1/2” 65 ft/lbs 90ft/lbs 12MM 55ft/lbs 75ft/lbs
9/16” 95 ft/lbs 130ft/lbs 14MM 85ft/lbs 120ft/lbs
5/8” 135ft/lbs 175ft/lbs 16MM 130ft/lbs 165ft/lbs
3/4” 185ft/lbs 280ft/lbs 18MM 170ft/lbs 240ft/lbs
Dodge Ram 2500/3500 2010-18 EXO Bumper
921310070
*31007BAG1*
31007BAG1

1. Place the vehicle in park and remove the 4 bolts from tow hook on the front and the back side of the bumper on the
drivers and passengers side, use a 18mm socket and wrench. See Photos 1 and 2. Save bolts for reuse.
2. Using the removed bolts from the tow hooks, install the EXO bumper brackets onto the drivers and passengers side.
See Photo 3. Measure 31 13/16 of an inch from the center of the hole to center of hole on the bottom of the brack-
ets. Do not tighten at this time.
3. Install the EXO bumper onto the bumper brackets, just far enough that you can fully tighten the 4 bolts in the bumper
brackets on the drivers and passengers side. See Photo 4.
4. Slide the EXO bumper back, to line up the holes in the brackets, use the supplied 12mm x 120mm bolts, washers
and lock nuts. Do not fully tighten at this time. See Photo 5.
5. Install the supplied 1/2” x 3 1/2” bolts in the frame bracket as shown with the flat washers and lock nuts. See Photo
6. Fully tighten all bolts installed, Use a 19mm wrench and socket.
Photo 1 Photo 2
Photo 3 Photo 4
Photo 5 Photo 6
Remove 4 bolts. Remove 4 nuts from the back side.
Install bumper brackets. Install bumper and Tighten bolts on frame.
Install the 4.5 long bolt with hardware. Install the 3.5 bolts long with hardware.

6. Install the flush mount lights and winch per instructions included in corresponding kits.
7. Install the light bar in the mount with instructions included in light bar kit. See Photo 7.
8. Install the light bar mount on the bumper with the supplied 12mm x 35mm bolts, flat washers and lock nuts. See
Photo 8. Tighten using an 18mm wrench and socket.
9. Install the supplied d-rings.
Photo 7 Photo 8
Install light bar. Tighten light bar mount.

By purchasing any item sold by Rough Country, LLC, the buyer expressly warrants that he/she is in compliance with all
applicable , State, and Local laws and regulations regarding the purchase, ownership, and use of the item. It shall be
the buyers responsibility to comply with all Federal, State and Local laws governing the sales of any
items listed, illustrated or sold. The buyer expressly agrees to indemnify and hold harmless Rough
Country, LLC for all claims resulting directly or indirectly from the purchase, ownership, or use of the
items.