Royal LR2060MX User manual

LR2060MXIM0812
ROYAL®
1160 U.S. Highway 22 East
Suite 301
Bridgewater, NJ 08807
Made in China
Crosscut shredder
Operation Manual
LR2060MX
crosscut shredder
LR2060MX
ROYAL®
Consumer Information Products, Inc.
© Copyright
Royal Consumer Information Products, Inc.
2012, All Rights Reserved.

FEDERAL COMMUNICATIONS COMMISSION (FCC) RADIO FREQUENCY
INTERFERENCE STATEMENT INFORMATION TO THE USER
CAUTION: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. If applicable, connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for assistance.
Connection of peripherals to this unit requires the use of grounded, shielded cables to
ensure compliance with the Class B FCC limits.
IN CANADA:
This digital apparatus does not exceed the Class limits for radio noise emissions from
digital apparatuses set forth in the Radio Interference Regulations of the Canadian
Department of Communications.
5
LR2060MX
1-800-272-6229 {US}
1-888-266-9380 {Canada}
01-800-849-4826 {Mexico}

WARNING
ROYAL LR2060MX PAPER SHREDDER
1. ALWAYS keep out of the reach of children as serious injury could occur.
2. DO NOT place finger too close to feed slot as serious injury could occur.
3. AVOID getting jewelry, hair or loose clothing too close to feed slot as serious
injury could occur.
4. ALWAYS keep shredder off and unplugged when not in use.
5. ALWAYS unplug shredder when moving, cleaning or empting the waste
receptacle.
6. DO NOT attempt to feed more sheets of paper than specified on the feeder.
7. DO NOT attempt to shred materials other than paper, credit cards and CD’s
in the provided feed slots.
8. ALWAYS install shredder near the socket-outlet and have it easily accessible.
9. ALWAYS limit continuous shredding to the specified time as suggested in the
instruction manual.
10. ALWAYS empty the waste receptacle prior to the receptacle becoming full.
11. DO NOT attempt to operate shredder if the shredder is experiencing any
kind of problem.
12. DO NOT use flammable synthetic oil, petroleum-based or aerosol
products of any kind on shredder
DO NOT attempt to repair shredder yourself.
WARNING ICONS:
The Icons, on top of the shredder, warn the user of the potential dangers if the
shredder is used improperly
WARRANTY, REGISTRATION & TECHNICAL SUPPORT
PLEASE FILL OUT AND RETURN THE PRODUCT REGISTRATION CARD INCLUDED WITH
YOUR NEW ROYAL PRODUCT OR FILL OUT THE PRODUCT REGISTRATION FORM ON THE
ROYAL WEB PAGE AT: http:// www.royal.com.
BE SURE TO KEEP A COPY OF YOUR SALES RECEIPT!
STANDARD WARRANTY
ROYAL CONSUMER INFORMATION PRODUCTS, INC. ("Royal"), at 1160 U.S. Highway 22 East,
Suite 301 Bridgewater, NJ 08807 USA WARRANTS that your NEW Product is free of defects of
workmanship and materials. If there is a defect or malfunction of this product, Royal will repair it
free of charge as follows:
PARTS: New or comparable rebuilt parts in exchange for defective parts for ONE (1) YEAR
from date of customer purchase.
CUTTING BLADES: Royal provides a SEVEN (7) YEAR warranty on the cutter blades.
LABOR: Royal provides labor warranty for ONE (1) YEAR from date of end-user purchase.
Product must be sent postage prepaid and insured to Royal in accordance with the
warranty procedures outlined below. At completion of the repair, the consumer will
be responsible for return shipping charges from Royal, and for any parts or services
no longer covered under warranty.
This warranty does not apply to persons who purchased this product second-hand or used.
This warranty does not include adjustments, parts and/or repairs required by circumstances beyond
the control of Royal, including but not limited to fire or other casualty, accident, neglect, abuse,
misuse, abnormal use or battery leakage damages.
THERE ARE NO OTHER EXPRESSED WARRANTIES EXCEPT AS STATED HEREIN. AFTER
THE PERIOD OF EXPRESSED WARRANTY SET FORTH HEREIN, THERE ARE NO EXPRESSED
OR IMPLIED WARRANTIES AND THOSE EXCLUDED INCLUDE THOSE OF MERCHANTABILITY
AND FITNESS FOR PARTICULAR PURPOSE. Royal shall NOT be held liable for CONSEQUENTIAL
DAMAGES resulting from any failure, defect or malfunction of this product. Some States do not
allow limitations on how long an implied warranty lasts and some States do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitations may not apply to you.
WARRANTY PROCEDURES
TO OBTAIN SERVICE UNDER THE TERMS OF THIS WARRANTY:
Please do the following:
1. Send a copy of your original sales receipt showing original purchase date along with
your mailing address and a note describing the nature of the problem to:
Royal Consumer Information Products, Inc.
Warranty Processing
50 Hilton Street
Easton, PA 18042-7391 USA
Do Not Return the Product to This Address!
2. You will receive a return authorization number within 7-12 business days from the date
your return request is received if it is determined that there is a basis for a replacement
product. The return authorization form you receive will list the return procedures,
applicable charges, if any, and the correct shipping address for the returned product.
PRODUCT SUPPORT HOTLINE:
For questions on use of this product or this warranty call [phone] (in Canada call
1-888-266-9380 or in Mexico call +(52-55)-53-33-1333), Monday through Friday during
normal business hours. You can also e-mail Royal at: [e-mail]
4
WARNING
1
WARNING READ INSTRUCTION
BEFORE USE
NO LOOSE
CLOTHING
NO FINGERS
OR HANDS
NO
HAIR
NO AEROSOL
PRODUCTS
NO
CHILDREN

ROYAL LR2060MX CROSSCUT PAPER SHREDDER
Setup:
1. Make sure that the wastebasket is completely inserted into the shredder cabinet
and that it fits flush with in the cabinet.
2. Plug the power cord into any standard 120-volt AC outlet.
3. Depress the ON/OFF () button. The READY LED should light up. You are now
ready to start shredding.
Operating the shredder:
With the electrical cord plugged in, with the ON/OFF () button depressed, and with the
shredder wastebasket properly in place, the READY LED will light up. This means
that the shredder is now ready for operation. When paper is inserted into the feed
opening, the shredding process will start automatically and stop when the paper has
completed its travel through the feed opening. The ON/OFF () button is located on the
top of the shredder. Also located on top of the shredder is the FORWARD>> and
REVERSE << buttons. Their purposes are:
1. When the ON/OFF ( ) button is pressed, the shredding process will start when
paper is inserted into the feed opening and will continue until it has passed through
the feed opening.
2. The REVERSE<< button is used to assist in the removal of a paper jam, which
reverses the shredding process prior to a completed forward cycle, thus clearing
the cutters. When switching from REVERSE << to FORWARD >>, always allow
the motor to stop to prevent possible damage to the motor.
3. The ON/OFF () position is used to terminate the AC power to the shredder. It
is recommended to turn the shredder off when the shredder is not being used for
a prolonged period of time.
4. When the READY LED is lit, it lets the user know that the wastebasket is inserted
correctly and that the shredder is turned on and ready for use. If the READY LED
does not light up, make sure that the plug is plugged in, the basket is inserted
correctly and the ON/OFF () is depressed.
Shredder capacity:
The Royal LR2060MX will shred up to twenty (20) sheets of 20-lb. bond paper and will
accept paper widths up to 8 3/4 inches (222.25 mm). When shredding small material
like envelopes, receipts or a credit card insert them in the middle of the feed opening.
CD’s. DVD’s and credit cards should be placed in the designated slot.
Basket Full Sensor
The LR2060MX is equipped with an electronic basket full sensor. When the wastebasket
becomes full, the BINFULL LED will then illuminate. If this occurs, empty the wastebasket.
You can now resume normal shredding.
Cautions:
1. Keep all loose articles of clothing, ties, jewelry, hair or other small items
away from the feed opening to prevent injury.
2. Keep the shredder turned off or unplugged when not in use for prolonged
periods of time.
3. Remove all paper clips and staples from paper before shredding. The
Royal LR2060MX will cut staples, small paper clips and credit cards; however,
proper discretion is recommended.
4. Do not place hands or fingers into the shredder throat as serious injury
could result.
5. When manually changing feed direction, pause long enough for the motor
to stop.
2
ROYAL LR2060MX CROSSCUT PAPER SHREDDER
6. Always turn off or unplug the shredder prior to moving, cleaning or
emptying the wastebasket.
7. Empty the wastebasket frequently to avoid possible paper jams caused
by shredded material being pulled back into the cutter assembly.
8. Never allow children to shred or play with paper shredder or else serious
injury could result.
Paper jams and motor overload situations:
The Royal LR2060MX is equipped with an automatic motor overload protection
circuit. The duty cycle for the LR2060MX is rated for 60 Min. ON / 40 Min. OFF. The
LR2060MX will automatically terminate power in case of the following abnormal
situations:
1. Operating the shredder at the maximum 20-sheet capacity continuously for a
prolonged period of time.
2. Exceeding the shredding capacity, eg. Inserting more than twenty (20) sheets
of 20-lbs. paper in one pass, or if the paper is not fed squarely into the feed
opening.
Both abnormal operations may result in the activation of the automatic thermal motor
overload protection circuit, which terminates the power to the shredder. A paper jam
could cause the thermal motor overload protection to terminate AC power to the
motor. Never allow the shredder to remain in a jammed condition with the AC power
turned on. If this occurs you should:
In case of a minor paper jam the Overload LED will light up:
1. Grasp the excess paper from the top and pull it out as you depress the
REVERSE << button. Be careful not to place your fingers near the feed opening
or else serious harm could result.
2. Make sure that all of the excess paper has been removed from the feed opening.
3. You are now ready to resume normal shredding.
In case of a major paper jam the Overheat LED will light up:
1. Turn off or unplug the power cord from the AC outlet and wait at least 40
minutes for the thermal overload protection to reset.
2. Plug in the AC power cord and depress the ON/OFF ( ) button. If paper was
left inside the feed opening prior to the overload, press the reverse position
and grasp the excess paper from the top and pull it out. Be careful not to place
your fingers near the feed opening or serious harm could result. Clear any excess
paper shreds from the feed opening.
3. You are now ready to resume normal shredding.
Specifications:
Shred Type: Crosscut
Shred Width: 17/100 inches X 1 7/8inches
(4.31 mm x 47.62 mm)
Shredding Capacity: 20 Sheets
Duty Cycle: 60 min. ON / 40min. OFF
Feed Opening: 8 3/4inches (222.25 mm)
Weight: 36 lbs (16.32 Kgs)
Input: 120 volt AC, 6.0 amp.
3