Runva 2.5 PSD User manual

Warning!
Read the Book Before
Installation & Operation

CONTENTS
WARNING! SAFETY PRECAUTIONS .................................................... 1
TROUBLESHOOTING ............................................................................ 6
WINCH ASSEMBLY DRAWING ............................................................. 7
WINCH PARTS NUMBERS .................................................................... 8
SPECIFICATION ..................................................................................... 9

1
Warning (Keep This Paper)
About Using/Replacing The Steel Cable For The Winch
1. Spray Lube / Grease on Winch Cable Regularly
2. Start each pull with a minimum of 5 wraps around the drum
3. Use the bottom 2 layer for max efficiency
4. To Change / Replace Steel Cable / Rope:
 Clutch To (Freespool)
 Hand Pull Out Cable / Rope All The Way To The End
 Take Off The Bolt Lock On The Drum
 Take Off The Cable End
 Put In and Lock The New Cable / Rope End On The Drum
 Clutch To (Engage)
 Power In By The Switch
 Roll Back The Cable / Rope In Good Order

2

3

4

5

6
WINCH ASSEMBLY DRAWING
Runva 2.5P
17
19
8
24
23
20
21
22
2
3
18
16
15
13
14
12
10
30
7
89
5
4
6
8
3
1
2
11
30
32
33
31
25
27
28
29
26
54
4748
49
52
444546
5051
53

7
WINCH PARTS LIST
Runva 2.5P
No. Part # Qty Description Remark
1 P250100 1 Motor Assembly
2 P250001 4 Locking Washer Φ8
3 P250002 4 Cap Screw M8 x 20
4 P250003 1 Transition Shaft
5 P250004 2 Tie Bar
6 P250005 1 Hexagonal Shaft
7 P250006 1 Front Bush Drum
8 P250007 6 Spring Washer Φ6
9 P250008 1 Screw M6 x 8
10 P250009 2 Cap Screw M6 x 70
11 P250010 1 Drum
12 P250011 1 Rear Bush Drum
13 P250012 1 Front Thrust Washer
14 P250013 1 Gear Ring Output
15 P250200 1 Gear Carrier Assembly
16 P250014 1 Gear Ring
17 P250015 1 Thrust Washer
18 P250016 1 Gear Housing / End Bearing
19 P250017 1 Bearing Holder
20 P250018 1 Roller Bearing
21 P250019 1 Clutch axes
22 P250020 1 Cam Clutch Gear
23 P250021 1 Spring
24 P250022 1 Cover Clutch Housing
25 P250023 1 Roller Bearing
26 P250024 1 Elastic Collar
27 P250025 1 Clutch Handle
28 P250026 1 Locking Washer Φ5
29 P250027 1 Cap Screw M5 x 12
30 P250028 4 Cap Screw M6 x 25
31 P250029 2 Terminal Protector
32 P250300 1 Nylon Rope Assembly
33 P250030 1 Strap
34 P250031 2 Screw M8 x 20
35 P250032 2 Locking Washer Φ8
36 P250033 2 Thick Flat Washer Φ8
37 P250400 1 Aluminium fairlead
38 P250034 1 Mounting Channel
39 P250035 2 Hex Flange Nut M8
40 P250036 2 Screw M8 x35
41 P250037 2 Thick Flat Washer Φ8
42 P250038 2 Locking Washer Φ8
43 P250039 2 Hex Flange Nut M8
44 P250500 1 Swich Mounting Assembly
45 P250600 1 ATV Handlebar Switch
46 P250700 1 Remote Control
47 P250800 1 Relay
48 P250900 1 Battery Wire Assembly
49 P251000 1 Motor Wire Assembly
50 P251100 1 Cable Stopper Sets
51 P251200 1 Wireless Switch Emitter
52 P251300 1 Wireless Switch Receiver
53 P251400 1 Tree Trunk Savers
54 P251500 1 Y Cable
55 P251600 1 Bow Type Shackle
56 P251700 1 Snatch Block

8
SPECIFICATION
Rated line pull 2500 lbs (1134 kgs)
Motor: permanent
magnet 12V:Input: 1.9 kW/ 2.6hp; Output: 0.8 kW/ 1.1hp
Gear reduction ratio 170:1
Cable (Dia.× L) Ø3/16"×45.9' (Ø 4.8mm×14.0m)
Drum size (Dia.× L) Ø1.46"×3.15" (Ø 37mm×80 mm)
Mounting bolt pattern 3.13" (79.5 mm) 2-M8
Item RUNVA 2.5P
Overall dimensions
(L×W×H) 12.7"×4.5"×4.4"
323mm ×113mm ×112 mm
+Pull , Speed, Amperes, Volts(First layer):
Line Pull Line Speed ft/min(m/min) Current A
Ibs (kgs) 12V DC 24V DC 12V DC 24V DC
0 14.1(4.3) / 20 /
500(227) 9.8(3.0) / 55 /
1500(680) 7.5(2.3) / 95 /
2500(1134) 4.3(1.3) / 160 /
Line Pull And Rope Capacity In Layer
Lay of wire
rope Rated line pull lbs(kgs) Total rope on the drun ft(m)
1 2500(1134) 6.9(2.1)
2 2033(922) 15.1(4.6)
3 1713(777) 24.3(7.4)
4 1480(671) 34.1(10.4)
5 1303(591) 45.9(14.0)
Buy It Online At Dealer Website: www.canadawinch.com