Runva 9.5 XS Guide

Warning!
Read the Book Before
Installation & Operation

CONTENTS
PACKING LIST (COLOR MAYBE DIFFERENT) .................................... 1
WARNING! SAFETY PRECAUTIONS .................................................... 2
TROUBLESHOOTING ............................................................................ 6
WINCH ASSEMBLY DRAWING ............................................................. 7
WINCH PARTS NUMBERS .................................................................... 8
SPECIFICATION ..................................................................................... 9
Wiring Instruction

1
Packing list (Color Maybe Different, All In One Box)
Warning!
1. Spray Lube / Grease on Winch Cable Regularly
2. Start each pull with a minimum of 5 wraps around the drum.
3. Use the bottom 2 layer for max efficiency.

2

3

4

5

6
TROUBLE SHOOTING
WARNING - Adjustment braking angle method: The spring according to the spring
gyrotropic pre-tight two weeks, then shows the spline tooth set according to following
braking cutaway view the adjustment angle for 20°±5°.
SYMPTOM POSSIBLE CAUSE SUGGESTED ACTION
Motor does not
turn on
-Switch Assembly not
connected properly
-Loose battery cable
connections
-Defective switch
assembly
-Defective motor
-Water has entered
motor
-Insert switch assembly all the way into the
connector.
-Tighten nuts on all cable connections.
-Replace switch assembly.
-Check for voltage at armature port with Switch
pressed. If voltage is present, replace motor.
-Allow to drain and dry. Run in short bursts
without load until completely dry.
Motor runs but
cable drum does
not turn
-Clutch not engaged
-Turn clutch to the “In” position. If problem
persists, a qualified technician needs to check
and repair.
Motor runs slowly
or without normal
power
-Insufficient current or
voltage
-Battery weak recharge. Run winch with vehicle
motor running.
-Loose or corroded battery cable connections.
Clean, tighten, or replace.
Motor overheating
-Winch running time
too long -Allow winch to cool down periodically.
Motor runs in one
direction only
-Defective switch
assembly.
-Loose or corroded battery cable or motor
cable connections. Clean and tighten.
-Repair or replace switch assembly.
Winch braking
malfunction.
-Winch working in
wrong direction.
-Brake slice worn or
worn not.
-Change winch working direction looking is to
clockwise look at the motor end
- Simply readjusted the braking angle or
replaces the new brake slice.

7
WINCH ASSEMBLY DRAWING
9.5Xs
25
26
27
23
21
22
24
28
29
19
18
6
5
38
36
37
10
34
35
3
16 17 4
15
14
12
11
8
5
7
910
13
8
12
13
4
1
2
36
20
3
30
5431
32
OUT
IN
33
39

8
WINCH PARTS NUMBERS
9.5Xs
No. Part # Qty Description Remark
1 X800001 3 Terminal Protect
2 X800100-SG 1 Motor Assembly
3 X800002 6 Cap Screw M10 x 35
4 X800003 6 Lock Washer Φ10
5 X800004 6 Think Flat Washer Φ10
6 X800005 4 Hex Nut M10
7 X800200 1 Break / Shaft Assembly
8 X800006 2 Bushing—Drum
9 X800007-SG 2 Tie Bar
10 X800008 2 Ring Seals
11 X800009 1 Cap Screw M6 x 10
12 X800010 4 Lock Washer Φ8
13 X800011 4 Cap Screw M8 x 30
14 X800300-SG 1 Drum Assembly
15 X800012 10 Screw M4 x 25
16 X800013 10 Lock Washer Φ4
17 X800014 1 End Bearing
18 X800015 1 Gasket
19 X800016 1 Gear—Ring
20 X800400 1 Gear Carrier Assembly（Output）
21 X800500 1 Gear Carrier Assembly（Intermediate）
22 X800600 1 Gear Carrier Assembly（Input）
23 X800017 1 Gear—Input Sun
24 X800018 1 Trust Washer
25 X800019 1 Gear—Housing
26 X800020 1 Clutch Screw
27 X800021 1 Ring Seals
28 X800022 1 Clutch Cover
29 X800023 1 Clutch Handle
30 X800024 2 Locknut M10
31 X800700 1 Roller Fairlead
32 X800900 1 Remote Control Switch（RC3）
33 X801000 1 Cable Assembly
34 X800029 1 Strap
35 X800800-SG 1 Control Box
36 X800030 4 Hex Head Screw M8 x15
37 X800032 2 Plug Screw M5 x 8
38 X800033 2 Soleplate Bracket
39 X800034 4 Locknut M8

9
SPECIFICATION
Rated line pull 9500 lbs (4309 kgs)
Motor: series wound 12V:Input: 4.6kW / 6.1hp; Output: 2.1kW / 2.8hp
24V:Input: 6.5kW / 8.1hp; Output: 2.8 kW / 3.8hp
Gear reduction ratio 230:1
Cable (Dia.× L) Ø5/16"×49.9 ' (Ø8.1mm×15.2m)
Drum size (Dia.× L) Ø2.48 "×4.7 " (Ø63mm×120mm)
Mounting bolt pattern 5.9 "×4.5 " (151mm×114.3 mm) 4-M10
Overall dimensions
(L×W×H)
17.2"×6.3"×10.7"
437mm ×160 mm ×272 mm
Net weight
Ibs(kg)
65.0
29.5
Pull, Speed, Amperes, Volts (First layer):
Line Pull Line Speed ft/min (m/min) Current A
Ibs (kgs) 12V DC 12V DC
0 19.7 (6.0) 80
3000(1361) 12.5 (3.8) 170
6000(2722) 9.8（3.0） 260
9500(4309) 6.2（1.9） 380
Line Pull And Rope Capacity In Layer
Layer Rated line pull lbs (kgs) Total rope on the drum ft (m)
1 9500(4309) 9.8(3.0)
2 7706(3495) 24.6 (7.5)
3 6482(2940) 42.7(13.0)
4 5593(2537) 45.9 (14.0)