Rutland County Garden Furniture Barleythorpe picnic table and bench set User manual

Assembly Instructions
Barleythorpe picnic table
and bench set
1
Before you commence the assembly process, we recommend that you read these instructions
thoroughly beforehand to familiarise yourself with the assembly process and to also check that you have
the correct components. If for any reason you need assistance, you can find our contact details on the
final page of these instructions.
We highly recommend that any assembly is carried out on a flat, level surface if possible and that you
use another person to assist you if necessary.
Package contents
Tools required
1 x Table top
2 x Seats
2 x Table A frames
2 x Seats backrests
4 x Bench A frames
4 x Backrest supports
6 x Cross braces (4 x for 3 & 4ft sets)
4 x M8 Coach screws - 70mm
44 x M8 Coach screws - 60mm
44 x Cover caps
* 8ft version additionally includes - 2 x seat supports and braces, 8 x
60mm Coach screws and 8 x cover caps.
10mm socket or spanner
The Barleythorpe picnic table and bench set

Barleythorpe picnic table and bench set
Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,
Aslackby, Sleaford, Lincs, NG34 0HZ.
Company No: 11025348 VAT No: 282569762
2
Step 1
Step 2
Ensure that you have all of the correct parts as listed
on the front page of these instructions, including any
fixings. (5 to 7ft set components shown here)
Lay the table top upside down on a clean, flat surface
taking care not to damage it. Now line up one of the
table A-frames centrally on the table top as shown in
step 3.
Step 3
Step 4
Place one of the table A-frames centrally against the
fixing batten ensuring that the gap at the table edge
is the same on both sides. Now, using 2 of the
supplied 70mm coach screws and the pre drilled
holes, secure the table A-frame to the fixing batten
on the table top.
Place a cross brace in position as shown, ensuring
that it is flush with the underside of the table A-frame
and proceed to step 5.

Barleythorpe picnic table and bench set
Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,
Aslackby, Sleaford, Lincs, NG34 0HZ.
Company No: 11025348 VAT No: 282569762
3
Step 5
Step 6
Ensure that the brace is lined up centrally on the
table and attach it to the A-frame with a 60mm coach
screw.
Make sure that the brace is still aligned centrally on
the table and affix the other end to the table top with
a 60mm coach screw as shown. Repeat steps 3 -6 to
finish the table assembly and proceed to step 7.
Step 7
Step 8
For an 8ft model, follow Steps 7 to 10. Place one of
the seat panels upside on a flat surface and place the
seat support adjacent to the centre batten...
...and aligned centrally on the seat panel before fixing
into place with 2 x 60mm coach screws as shown.

Barleythorpe picnic table and bench set
Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,
Aslackby, Sleaford, Lincs, NG34 0HZ.
Company No: 11025348 VAT No: 282569762
4
Step 9
Step 10
Now place the brace set support brace as shown so
that it is also aligned centrally...
...before fixing into place with a 60mm coach through
the brace into both the support and the underside of
the seat panel.
Step 11
Step 12
Lay one of the bench seats face down on the flat
surface as you did with the table top.
Place one of the bench A-frames centrally against the
fixing batten ensuring that the gap at the bench edge
is the same on both sides. Now, using 4 of the
supplied 60mm coach screws and the pre drilled
holes, secure the bench A-frame to the fixing batten
on the seat and repeat for the remaining 3 A- frames.

Barleythorpe picnic table and bench set
Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,
Aslackby, Sleaford, Lincs, NG34 0HZ.
Company No: 11025348 VAT No: 282569762
5
Step 13
Step 14
For a 3 or 4ft set, take one of the bench braces and
align it between the two A-frames...
...before securing into place using 2 60mm coach
screws at either end as shown.
Step 15
Step 16
For a 5 to 8ft set, place a brace aligned centrally on
the seat as shown and affix to the bench with a
60mm coach screw into the seat...
...and another 60mm coach screw through the A-
frame into the brace.