Rutland County Garden Furniture Morcott Single Bin Store User manual

Assembly Instructions
The Morcott Single Bin Store
1
Before you commence the assembly process we recommend that you read these instructions thoroughly beforehand to
familiarise yourself with the assembly process and to also check that you have the correct components. If for any reason you
need assistance, you can find our contact details on the final page of these instructions.
We highly recommend that any assembly is carried out on an open flat, level surface if possible with sufficient space.
Tools required:
10mm spanner/socket, No2 Pozidriv screwdriver (or electric driver), 2 x
25mm wooden spacer blocks (included).
Components
16 x 65mm,
2 x75mm screws
Latch keep & 10
black screws
Prop fixing
Left panel
Right panel
Back panel
Door
Lid assembly
Prop
Finishing strip
Metal bar
Chain

The Morcott Single Bin Store
Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,
Aslackby, Sleaford, Lincs, NG34 0HZ.
Company No: 11025348 VAT No: 282569762
2
Step 1
Step 2
Begin by arranging the left panel (the one with the small
wood block attached to the front post) and the back
panel at 90° to each other, with the back panel raised up
on the spacer blocks by approximately 25mm. Use 3 x
65mm screws to secure as shown.
Now add the right hand panel, fixing in the same way with
3 x 65mm screws.
Step 3
Step 4
Carefully lay the assembly on its back and attach the
metal bar to the front bottom edge of the 2 front posts as
shown, securing in place with 2 x 65mm screws per post.
Stand the assembly back up and lower the lid assembly
into place so that the hinge bar is centred across the rear
posts and fix into place with a 75mm screw into each post.

The Morcott Single Bin Store
Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,
Aslackby, Sleaford, Lincs, NG34 0HZ.
Company No: 11025348 VAT No: 282569762
3
Step 5
Step 6
Returning to the front of the store, place the finishing
strip against the 2 front posts as shown with the screw
holes configured to create a triangle and slide it
upwards...
…until it is just touching the underside of the lid. Now fix
both ends in place with 3 x 65mm screws per post.
Step 7
Step 8
Align the door (hinge side on the left) so that the top edge
clears the underside of the finishing strip by approx 10mm
and each hinge leaf sits flat against the post with the
knuckles resting against the front edge of the post. Secure
the hinges in place using 8 x black screws.
Position the cabin latch keep on the post and aligned
horizontally with the latch as shown. Secure in place with
2 x black screws.

The Morcott Single Bin Store
Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,
Aslackby, Sleaford, Lincs, NG34 0HZ.
Company No: 11025348 VAT No: 282569762
4
Step 9
Step 10
Take the coach bolt from the prop fixing and push it
through the hole in the prop, add a washer and then push
through the hole in the lid batten as shown.
Place another washer over the coach bolt and finally the
securing nut. Tighten with a spanner or socket until fully
tight and then back off until the prop is able to swing
freely.
Step 11
Step 12
If your bin lid has a suitable handle you may use the chain
provided to attached this to the store lid. Undo the nut
and slip one end over the coachbolt, then pass other end
through the handle and then over the end of the coach
bolt, pulling chain through until it is tight enough. Now re-
attach the nut.
Your Morcott Single Bin Store is now complete.
We hope that you found your product quick and easy to assemble but if not and you require any further assistance or have
any questions you can contact us by telephone on: 01778 440803
Email: [email protected].uk www.rutlandcountygardenfurniture.co.uk