Ryobi P320 User manual

12
3
FIGURE 1
Under some conditions, the unit may not deliver
a nail when the air pressure dial is turned to the
MAXIMUM pressure setting. The user may need to
decrease the pressure setting for desired operation.
(Refer to Setting the Air Pressure in the operator’s
manual page 9.)
FIGURE 2
NOTICE:
Remove battery pack before performing any of
the steps described below.
Driving too deeply into the material, excess debris, or
jammed nails may lead to a driver blade being stuck
at its bottom position.
The driver blade can usually be returned to its
operating position by depressing the work contact
element against a scrap piece of wood and squeezing
the trigger.
If this does not automatically return the drive blade
into the tool, remove the battery and refer to the
figure 2 and instructions in the operators manual on
removing a jammed nail.
(Refer to Removing a Jammed Brad Nail in the
operator’s manual page 10.)
990000552
2-21-13 (REV:01)
OPERATOR’S MANUAL
ADDENDUM
P320
Fig. 1
Fig. 2
A
B
C
D
A - Air pressure dial (cadran de pression d’air, cuadrante de
presión de aire)
B - Index arrow (flèche repère, flecha indicadora)
C - Decrease pressure (réduire la pression, disminuir la presión)
D - Increase pressure (augmenter la pression, aumentar la
presión) ONE WORLD TECHNOLOGIES, INC.
1428 Pearman Dairy Road, Anderson, SC 29625
USA
1-800-525-2579 • www.ryobitools.com
A subsidiary of Techtronic Industries Co., Ltd.
OTC: TTNDY
A
C
D
A - Screwdriver (tournevis, destornillador)
B - Latch (loquet, pestillo)
C - Jam release (déblocage, soltador)
D - Driver blade (lame d’entraînement, hoja de empuje)
A
B
For Ryobi Customer Service
call 1-800-525-2579.

12
3
FIGURE 1
Under some conditions, the unit may not deliver
a nail when the air pressure dial is turned to the
MAXIMUM pressure setting. The user may need to
decrease the pressure setting for desired operation.
(Refer to Setting the Air Pressure in the operator’s
manual page 9.)
FIGURE 2
NOTICE:
Remove battery pack before performing any of
the steps described below.
Driving too deeply into the material, excess debris, or
jammed nails may lead to a driver blade being stuck
at its bottom position.
The driver blade can usually be returned to its
operating position by depressing the work contact
element against a scrap piece of wood and squeezing
the trigger.
If this does not automatically return the drive blade
into the tool, remove the battery and refer to the
figure 2 and instructions in the operators manual on
removing a jammed nail.
(Refer to Removing a Jammed Brad Nail in the
operator’s manual page 10.)
990000552
2-21-13 (REV:01)
OPERATOR’S MANUAL
ADDENDUM
P320
Fig. 1
Fig. 2
A
B
C
D
A - Air pressure dial (cadran de pression d’air, cuadrante de
presión de aire)
B - Index arrow (flèche repère, flecha indicadora)
C - Decrease pressure (réduire la pression, disminuir la presión)
D - Increase pressure (augmenter la pression, aumentar la
presión) ONE WORLD TECHNOLOGIES, INC.
1428 Pearman Dairy Road, Anderson, SC 29625
USA
1-800-525-2579 • www.ryobitools.com
A subsidiary of Techtronic Industries Co., Ltd.
OTC: TTNDY
A
C
D
A - Screwdriver (tournevis, destornillador)
B - Latch (loquet, pestillo)
C - Jam release (déblocage, soltador)
D - Driver blade (lame d’entraînement, hoja de empuje)
A
B
For Ryobi Customer Service
call 1-800-525-2579.

12
3
FIGURE 1
Under some conditions, the unit may not deliver
a nail when the air pressure dial is turned to the
MAXIMUM pressure setting. The user may need to
decrease the pressure setting for desired operation.
(Refer to Setting the Air Pressure in the operator’s
manual page 9.)
FIGURE 2
NOTICE:
Remove battery pack before performing any of
the steps described below.
Driving too deeply into the material, excess debris, or
jammed nails may lead to a driver blade being stuck
at its bottom position.
The driver blade can usually be returned to its
operating position by depressing the work contact
element against a scrap piece of wood and squeezing
the trigger.
If this does not automatically return the drive blade
into the tool, remove the battery and refer to the
figure 2 and instructions in the operators manual on
removing a jammed nail.
(Refer to Removing a Jammed Brad Nail in the
operator’s manual page 10.)
990000552
2-21-13 (REV:01)
OPERATOR’S MANUAL
ADDENDUM
P320
Fig. 1
Fig. 2
A
B
C
D
A - Air pressure dial (cadran de pression d’air, cuadrante de
presión de aire)
B - Index arrow (flèche repère, flecha indicadora)
C - Decrease pressure (réduire la pression, disminuir la presión)
D - Increase pressure (augmenter la pression, aumentar la
presión) ONE WORLD TECHNOLOGIES, INC.
1428 Pearman Dairy Road, Anderson, SC 29625
USA
1-800-525-2579 • www.ryobitools.com
A subsidiary of Techtronic Industries Co., Ltd.
OTC: TTNDY
A
C
D
A - Screwdriver (tournevis, destornillador)
B - Latch (loquet, pestillo)
C - Jam release (déblocage, soltador)
D - Driver blade (lame d’entraînement, hoja de empuje)
A
B
For Ryobi Customer Service
call 1-800-525-2579.