Ryobi EPS80RS User manual

GB USER’S MANUAL 1
FR MANUEL D’UTILISATION 5
DE BEDIENUNGSANLEITUNG 10
ES MANUAL DE UTILIZACIÓN 15
IT MANUALE D’USO 20
NL GEBRUIKSHANDLEIDING 25
PT MANUAL DE UTILIZAÇÃO 30
DK BRUGERVEJLEDNING 35
SE INSTRUKTIONSBOK 39
FI KÄYTTÄJÄN KÄSIKIRJA 43
NO BRUKSANVISNING 47
RU РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ 51
PL INSTRUKCJA OBSŁUGI 56
CZ NÁVOD K OBSLUZE 61
HU HASZNÁLATI ÚTMUTATÓ 65
RO MANUAL DE UTILIZARE 70
LV LIETOTĀJA ROKASGRĀMATA 75
LT NAUDOJIMO VADOVAS 79
EE KASUTAJAJUHEND 83
HR KORISNIČKI PRIRUČNIK 87
SI UPORABNIŠKI PRIROČNIK 91
SK NÁVOD NA POUŽITIE 95
GR ΟΔΗΓΙΕΣ ΧΡΗΣΗΣ 99
TR KULLANiM KILAVUZU 104
EPS80RS
GB ORIGINAL INSTRUCTIONS | FR TRADUCTION DES INSTRUCTIONS ORIGINALES | DE ÜBERSETZUNG DER ORIGINALANLEITUNG | ES TRADUCCIÓN DE LAS
INSTRUCCIONES ORIGINALES | IT TRADUZIONE DELLE ISTRUZIONI ORIGINALI | NL VERTALING VAN DE ORIGINELE INSTRUCTIES | PT TRADUÇÃO DAS INSTRUÇÕES
ORIGINAIS | DK OVERSÆTTELSE AF DE ORIGINALE INSTRUKTIONER | SE ÖVERSÄTTNING AV DE URSPRUNGLIGA INSTRUKTIONERNA | FI ALKUPERÄISTEN
OHJEIDEN SUOMENNOS | NO OVERSETTELSE AV DE ORIGINALE INSTRUKSJONENE | RU ПЕРЕВОД ОРИГИНАЛЬНЫХ ИНСТРУКЦИЙ | PL TŁUMACZENIE INSTRUKCJI
ORYGINALNEJ | CZ PŘEKLAD ORIGINÁLNÍCH POKYNŮ| HU AZ EREDETI ÚTMUTATÓ FORDÍTÁSA | RO TRADUCEREA INSTRUCŢIUNILOR ORIGINALE | LV TULKOTS
NO ORIĢINĀLĀSINSTRUKCIJAS | LT ORIGINALIŲINSTRUKCIJŲVERTIMAS | EE ORIGINAALJUHENDI TÕLGE | HR PRIJEVOD ORIGINALNIH UPUTA | SI PREVOD
ORIGINALNIH NAVODIL | SK PREKLAD POKYNOV VORIGINÁLI | GR ΜΕΤΑΦΡΑΣΗ ΤΩΝ ΠΡΩΤΟΤΥΠΩΝ ΟΔΗΓΙΩΝ | TR ORIJINAL TALIMATLARIN TERCÜMESI
80W PALM SANDER
PONCEUSE VIBRANTE DE POING 80W
80W EXZENTERSCHLEIFER
LIJADORA DE MANO 80W
LEVIGATRICE MANUALE DA 80W
80W HANDPALMSCHUURMACHIME
LIXADORA DE MÃO DE 80W
80W RYSTEPUDSER
PLANSLIPMASKIN 80 W
80 W KÄSIKÄYTTÖINEN HIOMAKONE
80W MULTISLIPER
РУЧНОЙ ШЛИФОВАЛЬНЫЙ СТАНОК, 80 ВТ
KOMPAKTOWA SZLIFIERKA OSCYLACYJNA 80 W
80 W DLAŇOVÁ BRUSKA
80 W-OS KÉZI CSISZOLÓGÉP
MAŞINĂDE ŞLEFUIT 80 W
80 W ROKAS SLĪPMAŠĪNA
80 W DELNINIS ŠLIFUOTUVAS
KÄSILIHVMASIN 80 W
MULTI BRUSILICA OD 80W
80 W ROČNI ELEKTRIČNI BRUSILNIK
80W RUČNÁ BRÚSKA
80W ΕΚΚΚΕΝΤΡΟ ΠΕΡΙΣΤΡΟΦΙΚΟ ΤΡΙΒΕΙΟ
80W AVUÇ IÇI ZIMPARA MAKINESI

Fig. 2 Fig. 3
Fig. 1
5
5
4
4
1
1
3
3
6
7
2
2
Fig. 4 Fig. 5

Fig. 6 Fig. 7
Fig. 8
Fig. 9
3
6
6
8
7
7
8
6

!"#$%&'(&)* !"#!$%!&%%&'#$()!#*(#!+,-!.&(/!#*&!$'%#.-0#$,'%!$'!#*$%!1('-()!2&3,.&!,4&.(#$'5!#*$%!1(0*$'&6
+&&,(&-$(*)* ! ")!&%#!$'/$%4&'%(2)&!7-&!8,-%!)$%$&9!)&%!$'%#.-0#$,'%!0,'#&'-&%!/('%!0&!1('-&)!(8('#!)(!1$%&!&'!%&.8$0&!
/&!):(44(.&$)6
+./&0(1) !;$##&!)&%&'!<$&!-'2&/$'5#!8,.!"'2&#.$&2'(*1&!/$&!=$'>&$%&!/$&%&.!;&/$&'-'5%(')&$#-'56
2+&,(.-3() ! ?%!$14.&%0$'/$2)&!7-&!)&(!)(%!$'%#.-00$,'&%!/&!&%#&!1('-()!('#&%!/&!)(!4-&%#(!&'!%&.8$0$,6
+&&,(4-$(,) ! @.$1(!/$!4.,0&/&.&!())(!1&%%(!$'!3-'9$,'&A!B!$'/$%4&'%(2$)&!)&55&.&!(##&'#(1&'#&!)&!$%#.-9$,'$!0,'#&'-#&!
'&)!1('-()&6
5,&*$#) ! =&#!$%!8('!&%%&'#$&&)!2&)('5!/(#!-!/&!$'%#.-0#$&%!$'!/&9&!5&2.-$C%(('>$D9$'5!)&&%#!8,,.()&&.!-!deze !
machine $'!5&2.-$C!'&&1#6!
+&,(67$) ! E!$'/$%4&'%F8&)!7-&!)&$(!(%!$'%#.-GH&%!/&%#&!1('-()!('#&%!/&!-#$)$9(.!(!1F7-$'(6
89:) ! I&''&!2.-5%('8$%'$'5!%C()!)J%&%!$5&''&1!$'/&'!$2.-5#(5'$'56
8;<,%=,%') ! I&#!K.!'L/8K'/$5#!(##!)K%(!$'%#.-C#$,'&.'(!$!/&''(!2.-C%('8$%'$'5!$''('!('8K'/'$'56
>0$"-$) ! M'!&*/,##,1('!8K)##K1K#L'#K!)-C&(!#K%%K!CK+##L,*D&&%%(!(''&#-#!,*D&&#!&''&'!CK+##LL',##,(6
+?='%<,@) ! I&#!&.!1&5&#!8$C#$5!(#!/-!)&%&.!/&''&!2.-C&.8&$)&/'$'5&'!3N.!/-!#(.!1(%C$'&'!$!2.-C6
ÇÌËχÌËe! èee‰ Ò·ÓÍÓÈ Ë Á‡ÔÛÒÍÓÏ ËÌÒÚÛÏeÌÚ‡ ÌeÓ·ıÓ‰ËÏÓ ÔÓ˜eÒÚ¸ ËÌÒÚÛ͈ËË ËÁ ̇ÒÚÓfl˘e„Ó
ÛÍÓ‚Ó‰ÒÚ‚‡.
AB'1')* !@.9&/!4.9+%#ć4$&'$&1!/,!-ŧ+#C,>('$(!#&5,!-.9ć/9&'$(A!'()&ŧ+!C,'$&09'$&!9(4,9'(þ!%$ĕ!9!9()&0&'$(1$!
9(>(.#+1$!>!'$'$&D%9+1!4,/.ĕ09'$C-6
Cś@,D-&E*0#$4$%(ė(F) ! O&4,-PQ8&D#&!#&'#,!4ʼnQ%#.,D!/ʼnQ8&A!'&P!%$!4ʼn&Ā#&#&!4,C+'+!-8&/&'R!8!#,1#,!'F8,/-6
G-1H,@,")* ! S&)#R#)&'T)!3,'#,%A!*,5+!(!D&)&'!*(%9'F)(#$!U#1-#(#V2('!3,5)()#!&)ŃQ.F%,C(#!(9!T9&12&!*&)+&9R%!&)Ń##!
&),)8(%%(W
+&,(ŏ-,)* ! ?%#&!&%&'ŏ$()!%ą!0$#$ŏ$!!$'%#.-0ŏ$-'$)&!/$'!(0&%#!1('-()!X'($'#&!/&!,4&.(.&(!(0&%#-$!(4(.(#6
Uzmanību! !Svarīgi, lai jūs pirms mašīnas darbināšanas izlasītu instrukcijas šajārokasgrāmatā.
Dėmesio! !Priešpradėdami eksploatuoti šį prietaisą, svarbu, kad perskaitytumėte šiose instrukcijose pateiktus
nurodymus.
Tähtis! Enne trelli kasutama hakkamist tuleb käesolevas juhendis esitatud juhised kindlasti läbi lugeda.
Upozorenje! O&,4*,/',!D&!/(!4.,Ā$#(#&!,8&!-4-#&!4.$D&!-4,.(2&!,8,5!-.&ā(D(6
I$",";($)* ! @.&/!-4,.(2,!#&5(!%#.,D(A!,28&9',!4.&2&.$#&!'(8,/$)(!$9!#&5(!4.$.,Ā'$C(6
Dôležité! Pre prácou s týmto zariadením je dôležité, by ste si prečítali pokyny v tomto návode.
ƥǂǁDŽǁLjƱ! ƚƲƿƴƼ ƴƴǂƴƲDžƺDžǁ ƿƴ ƷƼƴƵƯDŽƸDžƸ DžƼǃ DŽdžDŽDžƯDŽƸƼǃ DžNJƿ ǁƷƺƶƼǏƿ ƴdžDžǏƿ ǂƼƿ ƽƴƼ Džƺ ƻưDŽƺ DŽƸ
ƾƸƼDžǁdžǂƶƲƴ.
C-JJ'&) !Y$*(9×'!G()×ü#×.×)1(%×'/('!L'0&!2-!C×)(8-9/(!2-)-'('!#()$1(#)(.×!,C-1('×9!9,.-')-/-.6
<-2D&0#!#,!#&0*'$0()!1,/$3$0(#$,'%!Z!<,-%!.R%&.8&!/&!1,/$3$0(#$,'%!#&0*'$7-&%!Z[&0*'$%0*&!\'/&.-'5&'!8,.2&*()#&'!Z!
<-D&#,!(!1,/$3$0(0$,'&%!#R0'$0(%!Z!Y,'!.$%&.8(!/$!&8&'#-()$!1,/$3$0*&!#&0'$0*&!Z[&0*'$%0*&!>$D9$5$'5&'!8,,.2&*,-/&'!Z
Y,1!.&%&.8(!/&!1,/$3$0(GH&%!#R0'$0(%!Z!]&/!3,.2&*,)/!3,.!#&C'$%C&!J'/.$'5&.!Z!]&/!3L.2&*^))!3L.!#&C'$%C(!K'/.$'5(.!Z!
[&C'$%&#!1--#,C%&#!8(.(#(('!Z!]&/!3,.2&*,)/!,1!#&C'$%C&!&'/.$'5&.!Z!åÓ„ÛÚ ·˚Ú¸ ‚ÌeÒeÌ˚ ÚeıÌ˘eÒÍËe ËÁÏeÌeÌËfl Z!
_!9(%#.9&ŧ&'$&1!1,/+3$C(0D$!#&0*'$09'+0*!Z!_1ė'+!#&0*'$0C`0*!U/(Dś!8+*.(9&'+!Z a!1ŝ%9(C$!1V/,%Q#F%!D,5F#!3&''#(.#D-C!Z
<-2!.&9&.8(!1,/$3$0(ŏ$$),.!#&*'$0&!Z!Paturam tiesības mainīt tehniskos raksturlielumus / Pasiliekant teisędaryti techninius pakeitimus /
Tehnilised muudatused võimalikud /Podloæno tehniËkim promjenama Z[&*'$Ā'&!%4.&1&12&!/,4-bĀ&'&Z
Technické zmeny vyhradené / ƩǍ Džƺƿ ƸƼLJǎƾƴǀƺ DžƸLjƿƼƽǏƿ DžǂǁǁǁƼƱDŽƸNJƿ!Z![&C'$C!/&ù$ü$C)$C!*(CC×!%(C)×/×.
cdefdghiejfek?l6$'//!!!am dZhiZfc!!!mnhgnhm!@]

1
English
GB
FR DE ES IT NL PT DK SE FI NO RU PL CZ HU RO LV LT EE HR SI SK GR TR
DESCRIPTION
1. Switch trigger
2. Quick change hook and loop pad
3. Dust collection box
4. Sand paper
5. Live tool indicator
6. Cover
7. Finger pad
8. Lock
SPECIFIC SAFETY INSTRUCTIONS FOR
SANDERS
Always wear safety goggles and a dust mask when
sanding, especially sanding over-head.
The machine is not suitable for wet sanding.
Do not use sanding paper larger than needed.
Extra paper extending beyond the sanding pad can
also cause serious lacerations.
The dust box shall be equipped with the tool.
It should be emptied frequently. To connect dust box,
insert the adapter of dust box to the dust-collection
opening on the rear end of the sander.
WARNING
Do not throw sanding dust on an open fire because
materials in fine particle form may be explosive.
WARNING
A suitable breathing respirator must be worn while
sanding lead paint, some woods and metal to avoid
breathing the harmful/toxic dust or air.
SPECIFICATIONS
Voltage 230 V - 240 V 50 Hz
Power 80 W
Orbital minute 12000 min-1
Weight 0.95 kg
FEATURES
KNOW YOUR COMPACT FINISHING SANDER
See Figure 1.
Before using this product, familiarize yourself with all
operating features and safety requirements. However, do
not let familiarity with the tool make you careless.
SWITCH
This tool is equipped with a simple switch control located
near the front of the motor housing.
QUICK CHANGE HOOK AND LOOP PAD
The hook and loop design allows for quick change of
sanding sheets and scrubbing pads. It also enables you to
easily clean and reuse them.
CIRCULAR SANDING ACTION
The oscillating action of your sander produces very quick,
small circular motion of the sanding pad. The motion is
ideal for producing a fine finished grain or, when using the
scrubbing pad, removing light rust, paint and other build
up from the work surface.
DUST COLLECTION BOX
The dust box attaches to the sander and keeps dust to a
minimum.
ASSEMBLY
WARNING
The tool should never be connected to a power supply
when you are assembling parts, making adjustments,
cleaning, performing maintenance, or when the tool is
not in use. Disconnecting the tool will prevent accidental
starting that could cause serious injury.
SANDING DISC SELECTION
Selecting the correct size, grit and type of sand paper
is extremely important step in achieving a high quality
sanded finish. Aluminum oxide, silicon carbide, and
other synthetic abrasives are best for power sanding.
Natural abrasives, such as flint and garnet are too soft for
economical use in power sanding.
In general, coarse grit will remove the most material
and finer grit will produce the best finish in all sanding
operations. The condition of the surface to be sanded
will determine which grit will do the job. If the surface is
rough, start with a coarse grit and sand until the surface
is uniform. Medium grit may then be used to remove
scratches left by the coarser grit and finer grit used for
finishing of the surface. Always continue sanding with
each grit until surface is uniform.
Sheet/pad recommended use
80-grit sanding sheet Coarse sanding
120-grit sanding sheet Light sanding
150-grit sanding sheet Light sanding

2
English
GB
FR DE ES IT NL PT DK SE FI NO RU PL CZ HU RO LV LT EE HR SI SK GR TR
ATTACHING HOOK AND LOOP SANDING DISCS
See Figure 2.
1. Unplug the sander.
2. Align holes in hook and loop type sanding disc with
holes in pad, then carefully press fuzzy side of sanding
disc against pad as tightly as possible.
NOTE: Hook and loop type sanding discs can be reused
for the life of the sanding abrasive. It is recommended that
you keep the sanding disc backing pad clean to provide for
best adhesion. Clean occasionally by brushing lightly with
a small brush.
ATTACHING THE DUST BOX
See Figure 3.
The dust box provides a dust collection system for the
sander. Sanding dust is drawn up through the holes of the
sanding disc and collected in the dust box during sanding.
1. Unplug the sander.
2. Using a slight twisting motion, firmly slide dust box
assembly in blower exhaust on sander.
WARNING
Exercise caution when using this tool. Careless actions,
for even a fraction of a second, can result in serious
personal injury.
APPLICATIONS
You may use the sander for the purposes listed below:
Sanding on wood surfaces
Removing rust from and sanding steel surfaces
Polishing and scrubbing porcelain and metal
CAUTION
Keep the cord away from the sanding pad and position
the cord so that it will not be caught on lumber, tools, or
other objects during sanding.
WARNING
Always wear safety goggles or safety glasses with side
shields when operating the products. Failure to do so
could result in dust, shavings, or loose particles being
thrown into your eyes, resulting in possible serious
injury.
OPERATION
TURNING THE SANDER ON/OFF
See Figure 4.
Turn on the sander: Push the on/off switch to the left.
Turn off the sander: Push the on/off switch to the
right.
OPERATING THE SANDER
See Figure 5.
1. Secure the workpiece to prevent it from moving under
the sander.
WARNING
Unsecured workpieces could be thrown towards the
operator, causing injury.
WARNING
Keep your head away from the sander and the sanding
area. Your hair could be drawn into the sander causing
serious injury.
2. Place the sander on the workpiece so that all of the
sanding disc surface is in contact with the workpiece.
CAUTION
Avoid damaging the motor from overheating, be careful
not to let your hand cover the air vents.
3. Turn on the sander and move it slowly over the
workpiece.
NOTE: Hold the sander in front and away from you,
keeping it clear of the workpiece. Start sander and let the
motor build to its maximum speed, then gradually lower
the sander onto the workpiece. Move the sander slowly
across the workpiece using small circular motions.
Do not force. The weight of the unit supplies adequate
pressure, so let the sanding disc and sander do the work.
Applying additional pressure only slows the motor, rapidly
wears sanding disc and greatly reduces sander speed.
Excessive pressure will overload the motor causing
possible damage from motor overheating and can result in
inferior work. Any finish or resin on wood may soften from
the frictional heat.
Do not allow sanding on one spot too long as the sander’s
rapid action may remove too much material, making the
surface uneven.
Extended periods of sanding may tend to overheat the
motor. If this occurs, turn sander off and wait until sanding
disc comes to a complete stop, then remove it from

3
English
GB
FR DE ES IT NL PT DK SE FI NO RU PL CZ HU RO LV LT EE HR SI SK GR TR
workpiece. Remove your hand from vent area, remove
sanding disc, then with your hand removed from vent
area, turn sander on and run it free without a load to cool
motor.
CORNERS AND CREVICES
See Figure 6.
For detail sanding such as corners and crevices, use
the tip of the sanding pad with small back and forth
motions.
EMPTYING THE DUST BOX
See Figure 7.
For more efficient operation, empty the dust box when it
is no more than half full. This will permit the air to flow
through the box better. Always empty and clean the dust
box thoroughly upon completion of a sanding operation
and before placing the sander in storage.
WARNING
Collected sanding dust from sanding surface coatings
such as polyurethanes, linseed oil, etc., can self-ignite
in your sander dust box or elsewhere and cause fire.
To reduce the risk of fire, always empty your dust box
frequently (10-15 minutes) while sanding and never
store or leave a sander without totally emptying its dust
box. Also follow the recommendations of the coatings
manufacturers.
1. Unplug the sander.
WARNING
Failure to unplug the tool could result in accidental
starting causing possible serious injury.
2. Remove the dust box from the sander.
3. Shake out the dust.
4. Reattach the dust box to the sander.
NOTE: For a more thorough cleaning of the dust box,
remove dust box from frame, and shake out dust. Replace
dust box over frame then install dust box assembly on
sander.
CHANGING THE SANDING SHEETS
See Figure 8.
The sander is packed with sanding sheets and pads
designed for a variety of uses. To change sheets, simply
pull the used sheet off the base and attach the desired
sheet by pressing the sheet or pad onto the base of the
sander.
USING THE FINGER PAD
See Figure 9.
1. Open the finger pad cover.
2. Lower the finger pad and lock it in place.
3. Close the finger pad cover.
LIVE TOOL INDICATOR
This tool features a live tool indicator which illuminates as
soon as the tool is connected to the supply. This warns the
user that the tool is connected and will operate when the
switch is pressed.
MAINTENANCE
WARNING
The tool should never be connected to a power supply
when you are assembling parts, making adjustments,
cleaning, performing maintenance, or when the tool is
not in use. Disconnecting the tool will prevent accidental
starting that could cause serious injury.
WARNING
When servicing, use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
GENERAL
Avoid using solvents when cleaning plastic parts.
Most plastics are susceptible to various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
WARNING
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. They contain chemicals that can
damage, weaken or destroy plastic.
Electric tools used on fiberglass material, wallboard,
spackling compounds, or plaster are subject to
accelerated wear and possible premature failure because
the fiberglass chips and grindings are highly abrasive to
bearings, brushes, commutators, etc.. Consequently, we
do not recommended using this tool for extended work on
these types of materials. However, if you do work with any
of these materials, it is extremely important to clean the
tool using compressed air.

4
English
GB
FR DE ES IT NL PT DK SE FI NO RU PL CZ HU RO LV LT EE HR SI SK GR TR
WARNING
Always wear safety goggles or safety glasses with side
shields during power tool operation or when blowing
dust. If operation is dusty, also wear a dust mask.
LUBRICATION
All of the bearings in this tool are lubricated with a
sufficient amount of high grade lubricant for the life of
the unit under normal operating conditions. Therefore, no
further lubrication is required.
CLEANING THE SCRUBBING PADS
To ensure longer life and optimum performance,
periodically clean all sanding residue and foreign
materials from the scrubbing pads. This can be done
simply by rinsing the pad with warm water until all foreign
material has been washed away. After cleaning, gently
squeeze the pad to remove excess water and allow pad
to dry. Always store pads and sanding sheets flat in a cool
dry location.
CLEANING THE SANDING SHEETS
The sanding sheets that came with your sander are
made to be re-used. Therefore, it is important that they
be cleaned periodically to remove sanding residue and
foreign material that can accumulate over time.
To clean sanding sheets, rub the sheets with a hard rubber
block. You can also use the clean rubber sole of a shoe.
WARNING
Always remove scrubbing or sanding pad from sander
before cleaning. Failure to do so could cause serious
personal injury.
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing
of as waste. The machine, accessories
and packaging should be sorted for
environmental-friendly recycling.
SYMBOL
Safety Alert
V Volts
Hz Hertz
Alternating Current
W Watts
noNo load speed
min-1Revolutions or reciprocations per minute
Orbital diameter
CE Conformity
Double insulation
Wear ear protection
Wear eye protection
Please read the instructions carefully before
starting the machine.
Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist. Check with your
Local Authority or retailer for recycling advice.