Saab 32 025 686 User manual

Saab 9-5 4D M06-
900 Installation instructions
SCdefault
MONTERINGSANVISNING ·INSTALLATION INSTRUCTIONS
MONTAGEANLEITUNG ·INSTRUCTIONS DE MONTAGE
SITdefault
Saab 9-5 4D M06-
Parking assistance (SPA)
Accessories Part No. Group Date Instruction Part No. Replaces
32 025 686 9:40-06 Sep 05 32 025 688
E930A398
Important
To install the kit the car must be equipped with
towbar wiring harness provision.

2 32 025 688
Saab 9-5 4D M06-
1 SPA control module
2 Screw (x2)
3 Holder (x4)
4 Distance sensor (x4)
5 Connector bracket
6 Wiring harness, distance sensor
7 SPA wiring harness
8 Connector
9 Cable tie (x17)
10 Cable tie, rubber grommet
11 Rubber grommet
E930A399
2
4
3
6
1
10
9
11
8
5
7

32 025 688 3
Saab 9-5 4D M06-
Before starting work the visible sections of the
distance sensors and holders must be painted in
the same colour as the bumper shell.
1 Fold forward the rear seat seat cushions and
lower the rear seat backrests.
2 Open the boot lid and remove the luggage com-
partment floor.
3 Remove the scuff plate.
4Cars with CD changer: Remove the CD
changer and bracket.
5 Detach and fold aside the left-hand trim in the
luggage compartment and remove the insula-
tion pads (x2) in the rear of the body. The old
ones must be discarded and replaced with new.
6 Detach and fold aside the right-hand trim in the
luggage compartment and remove the insula-
tion pads (x2) in the rear of the body. The old
ones must be discarded and replaced with new.
Important
The layer of paint must not be thicker than 90mto
avoid affecting system functionality.
E930A400
2
3 3
5 6
2

4 32 025 688
Saab 9-5 4D M06-
7 Remove the nuts that hold the bumper. The
lower studs only have nuts if the car is equipped
with towbar.
8Cars with towbar: Remove the nuts for both
reinforcements.
9 Raise the car.
10 Remove the bumper bolts at the wheel
housings.
11 Cars with towbar: Detach the connector for the
towbar wiring harness and remove the four bolts
holding the towbar to the body.
12 Lower the car.
13 With help from an assistant, pull the bumper out
from the clips. Lift the bumper out backwards.
14 Remove the bumper rail from the protective
shell by detaching the retaining clips.
Important
Work carefully during removal so that paint dam-
age is avoided.
Important
The outer bolts are fitted in loose nut plates.
Important
Place the bumper on a soft, clean surface.
E930A402
7
11

32 025 688 5
Saab 9-5 4D M06-
15 Remove the cellular block from the bumper shell
(wedged into the protective shell's mounting
wedges).
16 Drill 31 mm holes (x4) in the pre-punched mark-
ings in the bumper shell.
17 File out the guide groove 1 x 1 mm. The guide
groove must be on the side of the hole facing the
left-hand side of the bumper shell.
18 Fit the distance sensors in the holders and then
in the bumper shell.
19 Pre-route the wiring harness in the centre foam
section. The connector comes out on the left-
hand side. Connect the wiring harness to the
sensors.
20 Fit the connector's holder to the left-hand side of
the bumper rail.
21 Fit the connector in the holder.
22 Fit the cellular block with wiring harness in the
bumper shell.
23 Guide the bumper rail in toward the bumper
shell's guide pin. Fit the bumper rail with any
reinforcements to the bumper shell.
24 Fit the remaining cellular blocks.
Important
Do not file too far! The cover would then not be
over the guide.
WARNING
Check that the wiring harness is not pinched.
Incorrect fitting can damage the wiring harness
and cause a short-circuit/fire.
E930A403
16
20 18
15,22 19

6 32 025 688
Saab 9-5 4D M06-
25 Fit the rubber grommet on the parking assist-
ance system's wiring harness with the funnel-
shaped end directed towards the car. The grom-
met must be located 370 mm from the end of the
taping at the cable terminals.
26 Remove the rubber plug below the left-hand tail
lamp.
27 Guide the wiring harness out through the hole
and fit the kit's rubber grommet.
28 Insert the cable terminals as follows:
1 Black (BK)
2 Brown (BN)
3 Yellow (YE)
4 Blue (BU)
5 Orange (OG)
6 Grey (GY)
29 Affix tape and fit a cable tie on the rubber
grommet.
E930A405
27
28

32 025 688 7
Saab 9-5 4D M06-
30 Fit in the bumper and plug in the connector.
31 Fit the bumper.
Tightening torque 40 Nm (30 lbf ft)
32 Cars with towbar: Screw the reinforcements
into the car.
Tightening torque 40 Nm (30 lbf ft)
33 Raise the car.
34 Fit the bumper bolts at the wheel housings.
35 Cars with towbar: Fit the connector for the tow-
bar wiring harness.
36 Cars with towbar: Fit the bolts and nut plates
holding the towbar to the body.
Tightening torque 40 Nm (30 lbf ft)
Important
Work carefully during fitting so that paint damage
is avoided.
E930A406
31
36
30

8 32 025 688
Saab 9-5 4D M06-
37 Attach the ground cable to the grounding point
in the luggage compartment below the left-hand
tail lamp.
38 Run the thicker section of the wiring harness
toward the left-hand wheel housing and the thin-
ner section along the luggage compartment sill
to the right-hand side of the car.
39 Plug the connector into the provision for the tow-
bar wiring harness.
Cars with towbar: Unplug the connectors and
plug both wiring harness connectors into them.
40 Plug the wiring harness connector into the pro-
vision for the CD changer and fit the blind plug
to the SPA harness connector. Affix anti-rattle
tape and secure with a cable tie to avoid rattle.
Cars with CD changer: Unplug the connectors
and plug each wiring harness connector into
them. Affix anti-rattle tape and secure with a
cable tie to avoid rattle.
41 Insert the screws in the control module holes,
connect the wiring harness to the control mod-
ule, and fit the control module with connectors
facing down onto the plate behind the rear seat
backrest. Tighten the screws.
42 Use cable ties (x17) to secure the wiring har-
ness along its entire route. Gather excess wiring
harness and secure it above the wheel housing.
E930A408
42
42
41
4239 42 42
40
42
42
42
42
37
42

32 025 688 9
Saab 9-5 4D M06-
43 Fit new insulation pads (2 on each side) in the
rear edge of the body.
44 Fit the side trims.
45 Cars with CD changer: Fit the CD changer
bracket, connect and fit the CD changer.
46 Fit the scuff plate.
47 Fit the luggage compartment floor.
48 Fold back the rear seat backrests and seat
cushions and close the boot lid.
49 With the ignition key in the ON position and
reverse gear engaged, check that the system
warns against objects in the rear by using tones.
The first tone is given when an object is at a dis-
tance of 1.8 metres. The signal then has a fre-
quency of 2 tones per second, but the number of
tones per second increases the closer the object
becomes to the vehicle and changes as follows:
·1.8 - 1.3 m: 2 tones/second
·1.3 - 0.9 m: 3 tones/second
·0.9 - 0.3 m: from 5 to 12 tones/second in
close stages
·0.3 m: continuous tone
E930A409
44
44
47
46 46
47