Safety Technology International EM243608A1 User manual

INSTALLATION OF EM243608A1 METAL PROTECTIVE CABINET WITH AC
All specications and information shown were current as of publication and are subject to change without notice.
EM243608A1 JULY2022
Mount Enclosure in Desired Location
Prior to Mounting A/C Unit.
INSTALLATION NOTES
1. Read and understand instruction manual before mounting and
operating A/C Unit.
2. Install gasket provided on to A/C unit.
3. Insert power cord and wires through cutout in enclosure.
4. Mount A/C unit to enclosure by resting EZ mount tabs on
cutout edge. This will hold A/C unit in place while bolts are
inserted.
5. Insert the (4) 1/4-20 x 3/4 inch bolts with washers. Make sure
the threads of all (4) bolts have engaged with the A/C unit
before tightening.
6. Tighten the 4 bolts evenly.
7. Replace door with the hinge pins if door was removed.
Three year warranty or a one year limited warranty (from date of purchase) on most products.
See website for details. Electronic warranty form at www.sti-usa.com/wc14.
B
A/C UNIT
INSTALL GASKET PROVIDED
ENCLOSURE
A
CUTOUT EDGE
1/4”-20 x 3/4”
BOLT & WASHER
(4) PROVIDED
HINGE PIN
TO REMOVE DOOR
PULL BOTH HINGE PINS.
“EZ” MOUNT TABS
DETAIL A
DETAIL B
PULL
REMOVE THE (4) SCREWS AND
REMOVE FRONT COVER TO ACCESS
TEMPERATURE CONTROLS.
(SEE MANUAL FOR DETAILS)
INLET AIR FILTER
REMOVE TO CLEAN
(SEE INSTRUCTION MANUAL)
TEMPERATUARE CONTROL
9.07 in.
(230mm)
8 in.
(203mm)
7.5 in.
(191mm)
6.60 in.
(168mm)
36 in.
(914mm)
15.75 in.
(400mm)
24 in.
(610mm)
FRONT COVER
EMEA
USA

EM243608A1 METAL PROTECTIVE CABINET WITH AC
All specications and information shown were current as of publication and are subject to change without notice.
EM243608A1 JULY2022
Three year warranty or a one year limited warranty
(from date of purchase) on most products. See website for details.
Electronic warranty form at www.sti-usa.com/wc14.
B
A/C UNIT
INSTALL GASKET PROVIDED
ENCLOSURE
A
CUTOUT EDGE
1/4”-20 x 3/4”
BOLT & WASHER
(4) PROVIDED
HINGE PIN
TO REMOVE DOOR
PULL BOTH HINGE PINS.
“EZ” MOUNT TABS
DETAIL A
DETAIL B
PULL
REMOVE THE (4) SCREWS AND
REMOVE FRONT COVER TO ACCESS
TEMPERATURE CONTROLS.
(SEE MANUAL FOR DETAILS)
INLET AIR FILTER
REMOVE TO CLEAN
(SEE INSTRUCTION MANUAL)
TEMPERATUARE CONTROL
9.07 in.
(230mm)
8 in.
(203mm)
7.5 in.
(191mm)
6.60 in.
(168mm)
36 in.
(914mm)
15.75 in.
(400mm)
24 in.
(610mm)
FRONT COVER
B
A/C UNIT
INSTALL GASKET PROVIDED
ENCLOSURE
A
CUTOUT EDGE
1/4”-20 x 3/4”
BOLT & WASHER
(4) PROVIDED
HINGE PIN
TO REMOVE DOOR
PULL BOTH HINGE PINS.
“EZ” MOUNT TABS
DETAIL A
DETAIL B
PULL
REMOVE THE (4) SCREWS AND
REMOVE FRONT COVER TO ACCESS
TEMPERATURE CONTROLS.
(SEE MANUAL FOR DETAILS)
INLET AIR FILTER
REMOVE TO CLEAN
(SEE INSTRUCTION MANUAL)
TEMPERATUARE CONTROL
9.07 in.
(230mm)
8 in.
(203mm)
7.5 in.
(191mm)
6.60 in.
(168mm)
36 in.
(914mm)
15.75 in.
(400mm)
24 in.
(610mm)
FRONT COVER