Sakamoto Model M175 User manual

●Introduction／Table of Contents １
●Purpose／Content ２
●Precautions concerning handling ３
●Instructions for Use ４
●Storage Instructions ５
User’s Manual (151218)
M175
Sakamoto Suction Simulator
－ＩＮＤＥＸ－
Please open your parcel and check the main unit
and accessories of the product immediately
upon receipt. If the products are delivered
damaged or with parts missing, please contact
our company or the distributor.
！
Note

- 1 -
Introduction
Thank you for purchasing our product, “Sakamoto Suction Simulator.”
Read this user’s manual carefully in order to use the product for a long
time appropriately.
This product is closely checked before factory shipment. However, when
this product arrives, open it soon, and check if anything on the main unit
and accessories are missing or broken.
Table of contents
Introduction／Table of Contents………………………. 1
Purpose／Content………………………………………… 2
Cautions on Use…………………………………………. 3
Instructions for use……………………………………… 4
Storage Instructions……………………………………… 5

- 2 -
Purpose
The following types of suction training can be performed:
1 Oral/nasal suction
2 Suction of secretions in inserted tubes
3 Suction of secretions in the tracheal cannula
Contents
１Main unit (including the bronchi, left and
right lungs, and stomach)
２Pseudo sputa
３Baby powder
４Lubricant oil
５Container for mixing pseudo sputa
６Muddler for mixing pseudo sputa
７Syringe with tube
８Large-size silicon cap 1 piece
９Small-size silicon cap 2 pieces
１０ Flushing funnel
１１ Flushing tube
１２ Tray
１３ Pseudo tracheal cannula
1
1
1
1
5
6
7
8
9
10
11
12
2
4
3
13

- 3 -
Cautions on Use
1. If resin products contact the head for a prolonged time, the head might be
deformed. Treat the product with sufficient care. In addition, do not remove the
epidermis of the head.
2. Due to the nature of the material, the face parts are likely to get dirty easily.
Note that stains of a ballpoint pen or marker on the product cannot be removed.
3. Light dirt on the face parts can be washed with neutral detergent.
(Do not use solvents, such as thinner, because they melt the resin parts.)
After cleaning, wipe off all remaining water and apply baby powder.
4. Apply the accessory silicon oil to this product before using catheters or tubes.
5. Be careful not to swallow the accessory pseudo sputa by mistake.
6. When the pseudo sputa have been used, store the model after disposing of them
completely and washing to dry the container sufficiently.
7. Do not use pseudo tracheal cannula for humans.
8. If anything strange is detected when this model is being used, stop using it and
notify us as soon as possible.
9. This product is a simulator for users to perform advanced training. Nonetheless,
it does not guarantee that a similar effect can be obtained by actual treatment.
10. Note in advance that this product is subject to change without notice to improve
it.

- 4 -
Instructions for use
1. Pick the main unit out of the storage case, and put it in a place where it cannot
slip, for example, a desktop.
2. Perform suction training by removing the lungs and attaching the accessory
small-size silicon caps to the two inner connectors (to protect sputa from
flowing in).
3. How to make pseudo sputa.
①Put 100ml of water into the container. Sprinkle pseudo sputa ten times in it.
Stir it well with muddler, until the mixture get thick.
②Then sprinkle pseudo sputa five more times, and stir it well, see until the
viscosity gets proper.
※It is possible to adjust the viscosity by increasing or decreasing the amount of pseudo
sputa powder.
4. Suck the pseudo sputa out with the syringe with tube and inject it into where to
practice suction training.
5. Before using the catheter or tube, apply the silicon oil.
6. Start suction training.
7. When feeding air, use the model after putting a lid on the incised portion of the
trachea.
8. It is possible to remove and wash the bronchi part after the training ends.

- 5 -
Storage Instructions
1. Remove the trachea and stomach.
Insert silicone cap (Large size) into thyroid
cricoid section. Insert flushing tube into the
esophagus.
2. Put the other edge of flushing tube into
a big size tray or sink.
3. Make a proper angle for the model by putting a blue box attached for
accessories on the back (head side) of the foundation of the model.
4. Suck pseudo sputa in the oral cavity with an aspirator as much as possible.
※When an aspirator is not available, remove pseudo sputa with the
syringe with tube.
5. Put water in the syringe with tube, inject into the oral cavity.
※When inject water, please note not to allow water to go between mask and
skull. Please be sure to inject water carefully because it can overflow if the
water is excessively put into the oral cavity.
6. Repeat it several times until the pseudo sputa is eliminated enough.
※Since it is difficult to eliminate pseudo sputa remained in the back of cheek,
it would be helpful to aim at the place with syringe with tube when inject
water.
7. Wipe out moisture gently after washing the model and dry internal of oral
cavity. Apply accessory baby powder on the head to avoid stickiness.
8. Do not store the product in a place exposed to direct sunlight or hot and humid
air. Product can deform in a bad storage condition.