Samsung MIM-D01AN User manual

DMS2.5
(Data Management Server2.5)
MIM-D01AN
MIM-D01AUN
BACnet Gateway
MIM-B17BN
MIM-B17BUN
LonWorks Gateway
MIM-B18BN
MIM-B18BUN
Air Conditioner
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.

E-2
XDo not attempt to install or repair the product by yourself.
XThe product contains no user-serviceable parts. Always consult authorized
service personnel for repairs.
XWhen moving, consult authorized service personnel for disconnection and
installation of the product.
XEnsure that the wall is strong enough to support the weight of the product.
XMust install the product with rated power supply.
XIn the event of a malfunction (burning smell, etc.), immediately stop operation,
turn off the electrical breaker, and consult authorized service personnel.
XNe tentez pas d’installer ou de réparer vous-même le produit.
XLe produit ne contient aucun composant interne susceptible d’être réparé par
l’utilisateur. Consultez toujours le personnel d’entretien agréé pour toute réparation.
XEn cas de déplacement, consultez le personnel d’entretien agréé pour tout
débranchement et toute installation du produit.
XAssurez-vous que le mur est suffisamment résistant pour supporter le poids du produit.
XVous devez raccorder le produit à une installation supportant sa puissance nominale.
XEn cas de dysfonctionnement (odeur de brûlé, etc.), arrêtez immédiatement le
fonctionnement, coupez le disjoncteur électrique et consultez le personnel
d’entretien qualifié.
WARNING
AVERTISSEMENT
CAUTION
ATTENTION
XDo not use inflammable gases near the product.
XDo not spill water into the product.
XDo not operate the product with wet hands.
XDo not install the product in a location where it will come into contact
with the combustible gases, machine oil, sulphide gas, etc.
XDo not press buttons with a pointed thing.
XDo not pull or bend the product cable excessively.
XDo not use the product for other purpose.
XDo not spray an insecticide or other combustible things on the product.
XDo not clean the product with benzene, solvents or other chemicals.
XDo not give a shock to the product or disassemble it by yourself.
XN’utilisez pas de gaz inflammable à proximité du produit.
XNe renversez pas d’eau dans le produit.
XNe manipulez pas le produit si vous avez les mains mouillées.
XN’installez pas le produit dans un lieu où il sera en contact avec des gaz combustibles,
de l’huile de machine, de l’hydrogène sulfuré, etc.
XN’appuyez pas sur les boutons avec un objet pointu.
XNe tirez pas sur le cordon d’alimentation du produit et ne le pliez pas excessivement.
XN’utilisez pas le produit dans un autre but que celui auquel il est destiné.
XNe vaporisez pas d’insecticide ou autre produit combustible sur le produit.
XNe nettoyez pas le produit en utilisant du benzène, des solvants ou autres produits
chimiques.
XN’appliquez pas de choc sur le produit et ne le désassemblez pas non plus vous-même.
Safety Precautions
Consignes de sécurité
xBefore using the DMS2.5, BACnet Gateway, LonWorks Gateway, read carefully these instructions.
xAfter reading the instructions, keep this user's manual in a handy and safe place.
If a user is changed, you must hand over the manuals.
xNever attempt to install the air conditioning system or to move the product by yourself.
xAvant d’utiliser le DMS2.5, BACnet Gateway, LonWorks Gateway, lisez attentivement ces consignes.
xAprès en avoir pris connaissance, conservez ce manuel d’utilisation dans un lieu sûr et à portée de
main. En cas de changement d’utilisateur, vous devez remettre les manuels.
xNe tentez jamais d’installer le climatiseur ou de déplacer le produit par vous-même.
English
Français

E-3
Contents
XGENERAL DESCRIPTION ....................................................... 4
XVIEWING THE PARTS ........................................................... 6
XBEFORE USE ...................................................................... 8
XMAIN FUNCTION ............................................................. 10
XSTARTING DMS2.5 ........................................................ 14
XCONTROL AND MONITORING ............................................. 20
XZONE MANAGEMENT ....................................................... 67
XSCHEDULE ..................................................................... 72
XEHP POWER CONSUMPTION INSPECTION ............................ 85
XCONTROL LOGIC MANAGEMENT ........................................ 96
XSYSTEM SETTINGS ......................................................... 109
XCHECK BEFORE USING PANEL .......................................... 161
XSETTING NETWORK INFORMATION .................................... 162
XCHECKING INDOOR/OUTDOOR UNIT INFORMATION ............ 164
XCHECKING DMS2.5 VERSION ........................................ 165
XDATA BACKUP SETTING .................................................. 169
XCHECKING ERROR INFORMATION ...................................... 170
XRESET PASSWORD ......................................................... 171
XBUTTON LOCK .............................................................. 172
XSAFETY HALT ................................................................ 173
XTROUBLESHOOTING ....................................................... 174
XSPECIFICATIONS ............................................................ 176
XLICENSE ....................................................................... 177
Note XThe contents and pictures used in this user manual
may be changed without advance notice for the
functional reinforcement and improvement of a
product.
This System is strictly restricted to authorized user.
Any illegal access shall be punished with a related-law.

E-4
General Description
The DMS2.5 is an Ethernet based device for central management of Samsung system air-
conditioners. It operates 24 hours without a separate management (PC).
Introduction of DMS2.5 (Data Management Server2.5)
The DMS2.5 provides the following advantages:
XEveryday Device–The DMS2.5 is operational all year long 24 hours.
X Independent Operation–The DMS2.5 can operate schedule control and power
distribution without a PC.
Note In order to run power distribution, relevant controllers need to be installed.
XRemote Control
Web – The DMS2.5 has a built-in web server function and can be accessed from a
remote location to operate status
monitoring, control, trouble history, and schedule setting of the system
air-conditioners.
Using an Upper Level Controller–When a separate upper level controller (S-NET
series) is used, a number of DMS2.5 can be controlled with one central management
system.
XData Storage–The DMS2.5 has its own database built-in, therefore, trouble history,
indoor unit installation information, and power distribution data can be saved and
retrieved.
XLarge Scale Management–At most 256 indoor units can be connected to one DMS2.5
and therefore, only one DMS2.5 can manage small and medium size buildings.
XAutomatic ”e-mail” sending–When an error is occurred, inform the error details to an
e-mail saved on DMS2.5.
Advantages of DMS2.5 System
Note XPlease be advised that once you are permitted access
to the system, you will be deemed to have consented
to having software relating this system automatically
updated or modified on a periodic basis.You will be
deemed to have consented to having software relating
this system automatically updated or modified on a
periodic basis.

E-5
XDMS2.5: The abbreviation of Data Management Server2.5.
XUpper Controller: S-NET 3, RMS and DMS2.5 which allows controlling by accessing to a
web page.
XOnOff Controller: A device that controls 16 groups of the DVM air conditioner.
A central control device of a DVM system which is located between a
DMS2.5 and an outdoor unit.
XAHU(Air Handling Unit): Executes heat exchange between air and cooling unit using
central air conditioning duct method.
XERV(Energy Recovery Ventilator): Ventilating system using heat recovery function.
Terms

E-6
Viewing the Parts
Front View
No. Name Description

LCD Display Display current time/ Check menu

Menu button Access to main menu
▼/▲button Select the function you want and set detailed functions in
main menu
Set button Check the function you want from main menu
and select it

Bottom cover Unfasten 2 screws on the bottom and separate the bottom
cover from DMS2.5. Then check cable connection part.



Name Description
Power Turns blue when the power is supplied.
CPU Alive Blinks in orange with 1 second intervals during normal
operation.
Ethernet–Linked Turns green during normal connection.
Ethernet–Active Blinks in orange during normal transmission/reception.
COM1~5 – TX Blinks in green during normal transmission.
COM1~5 – RX Blinks in green during normal reception.
Check Turns green when notice occurs.
Indicator

E-7
DI Terminal1
Connect Digital Input
- Channel 1~Channel 5
DI Terminal2
Connect Digital Input
- Channel 6~Channel10
DO Terminal 2
Connect Digital Output
- Channel 6~Channel 8
DO Terminal1
Connect Digital Output
- Channel 1~Channel 5
Power
Terminal
Connect
DMS2.5 adapter
Reset Button
Reset DMS2.5
RS485
Communication
terminal
Connect for RS485
communication with
devices such as OnOff
Controller/Outdoor
unit
- COM1 ~ COM5
Cable tie groove
Arrange cables connected to
DMS2.5
LAN Terminal
Connect LAN cable
Serial Terminal
Service agent checks error
status
SD Card Socket
Socket for sub memory (SD or MMC)
(Sub memory is for DMS2.5 program
update and set information saving)
※Purchase SD card separately.
XSeparate bottom cover by unfastening 2 screws on the bottom.
Bottom View
Reserved

E-8
XConnecting outdoor unit and DMS2.5
- You can control up to 80 outdoor units and 256 indoor units by using DMS2.5.
※You can connect up to 16 (outdoor) units per each communication channel of the
DMS2.5.
- If the number of connected outdoor unit increases, it may take long time for tracking.
(Max. 30 minutes)
PM05:45
OnOff
controller
DMS2.5
Internet
Web Client
RMS Senter
S-NET 3
TCP/IP
R5 485
(DVM Series)
Outdoor Unit
Max 256
Indoor units
SIM/PIM
Power meter
Before Use
System Configuration
Touch
Centralized
controller

E-9
XWindows 7 or later version
XInstall Internet Explorer 11 or later version
XInstall Silverlight 2.0 or later version
Web Browser Specification
Note XVisit internet homepage (http://www.microsoft.com/silverlight/) to download
Silverlight. Or you can download it through the download link which is noticed
automatically when the PC is connected to the Internet and you access to DMS2.5
for the first time.
XSilverlight operates normally with Windows 7 or later version.
It may not operate normally with former version of Windows.
All settings of DMS2.5 will be arranged in web page which built in DMS2.5.
You should access to DMS2.5 IP to use DMS2.5 web page.
There are 2 ways to access DMS2.5 IP.
(For about settings, refer to installation manual.)
XStatic IP setting
XDynamic IP(DHCP) setting
XBasically, only Private IP can be set to IP address. To use Public IP, you must set Enable
public IP as‘Enable’from the menu [System Settings]
£ [System environment setting].
- Private IP range: 10.0.0.0 ~ 10.255.255.255, 172.16.0.0 ~ 172.31.255.255,
192.168.0.0~192.168.255.255
Computer Settings for DMS2.5 Connection
X For devices that support new communication, you must set the communication mode
of the channel to 'NEW' from [System settings £Tracking] menu. Set of Indoor/outdoor
units, with conventional communication type, cannot be connected to DMS2.5 with new
communication.
X When 'NEW' is set as communication mode of the channel, virtual OnOff controller
address will be assigned.
(Channel 0: Virtual OnOff controller 11, Channel 1: Virtual OnOff controller 12,
Channel 2: Virtual OnOff controller 13, Channel 3: Virtual OnOff controller 14,
Channel 4: Virtual OnOff controller 15)
X The maximum number of indoor units that can be connected to each communication
channel of DMS2.5 RS485 is 128.
X Use this product only in a separate dedicated network.
Samsung electronics is not liable for any problems caused
by connecting it to the Internet or an intranet.

E-10
Device Type
Indoor Unit
Indoor unit communication error
Indoor unit sensor related error
Other errors
Outdoor Unit
Outdoor unit communication error
Pipe inspection error
Outdoor unit sensor related error
Outdoor unit related other errors
Communication error
such as OnO controller
Control device related communication
error
Main Function
The DMS2.5 saves at most 1024 cases of trouble history.
If the number of errors exceeds 1024, only the latest 1024 cases
are stored by deleting the oldest trouble history.
XDevice name, address, error occurrence time, error solvation
time, trouble history will be saved. You can check it in web
page or upper controller.
XWhen an error occurs, it sends trouble history to e-mail saved
in DMS2.5.
XSome functions available on DMS2.5 web page may not be
functional at BACnet Gateway and Lonworks Gateway.
For detailed function, refer to the installation manual or
contact Samsung Electronics.
Save Trouble History
The DMS2.5 receives/manages setting and control data from the
upper level controller and sends the received data to the lower
level system.
X Upper controller: S-NET 3, RMS and DMS2.5 which allows
controlling by accessing to a web page.
X S-NET 3: System air conditioner controlling and monitoring
program that is used by installing on a PC.
X RMS: A device which supervises operation status and break
down status by connecting to DMS2.5 for system air
conditioner remote service. If break down is detected,
it notifies service agent and makes fast service possible.
Interface with Upper Level Controller

E-11
Item Content Remark
Schedule Period Starting and ending date of a schedule
Exception Day
Setup
Set an exception day within a schedule period to
ignore the schedule control
Devices to
be applied Select devices to receive schedule control
Event
Set indoor unit operation modes
- Device On time
- Device O time
- Desired temperature
- Operation mode: Auto/Cool/Dry/Fan/Heat/O
- Remote control usage Enable RC/ Disable RC/
Cond.RC
- Fan speed: Auto/Low/Mid/High/Turbo
- Air ow: None/Vertical/Horizontal/All
- ERV operation mode: Auto/HeatEx/ByPass/Sleep
- ERV Fan speed: Low/High/Turbo
Weekly Repeat:
Maximum 10 events
per day
Daily Repeat:
Maximum 70 events
The schedule function of the DMS2.5 can be set through the Web
or using the upper level controller. 1day/Everyday/Every week
schedules can be set.
XEach schedule can be used selectively by using the run
schedule/stop schedule order.
XAt most 256 schedules can be set.
XIndoor unit control is possible at least 1 minute of interval by
set schedule.
Set and Run Schedule

E-12
System Architecture
The DMS2.5 calculates and distributes the power consumed by each indoor unit by
receiving the total power usage from the watt-hour meter interface modules (SIM/PIM)
and taking into account the operation status of the indoor units.
The DMS2.5 saves at most 1 year of data. After a year, the oldest data is deleted and
the latest data is saved. This data can be checked through the built-in Web page of
the DMS2.5 or by S-NET 3.
Save Integrated Power Distribution Data
Main Function (Continued)
PM05:45
OnOff
controller
DMS2.5
Internet
Web Client
RMS Senter
S-NET 3
TCP/IP
R5 485
(DVM Series)
Outdoor Unit
Max 256
Indoor units
Power meter
SIM
/PIM SIM /PIM
Touch
Centralized
controller

E-13
X Time segmentation is used to divide 24 hours into different sections and to distribute
power according to each section.
X
This function is used when the power consumption fee is different according to
different time slots or when a building is charged differently depending on the
consumption time.
X
1 section (A) is set as 24hours, and the factory default setting is set as 1 section.
The time, 24hours, can also be divided into 2 sections (A,B,A), 3 sections (A,B,C,A) or
4 sections (A,B,C,D,A)
X
DMS2.5 shows the result of the power distribution for each section you set.
Input manually (When setting 2 sections, 3 sections, and 4 sections)
Time Segmentation
If communication error occurs between DMS and the lower level controllers,
actual power consumption and the result of power distribution value may not be
same. Make sure to solve communication error status.
- Example of communication error : Communication error between DMS2.5 and
SIM(PIM)/SIM(PIM) and watt hour meter/
DMS2.5 and outdoor unit/indoor and outdoor
units.

E-14
Set the current time of DMS2.5 system.
X“2016/01/01 01:01:01” is factory setting. Set the current time as DMS2.5 system time.
You can set DMS2.5 time in [System Settings] [System environment setting]
(Refer to page 129~130)
Starting DMS2.5
Current time setting
Connecting devices
(1) Make sure the connection of communication cables(R1/R2) between DMS2.5 and other
devices such as outdoor units, control devices.
(2) Execute tracking.
XDMS2.5 communicates with outdoor unit and brings information about installed
indoor unit and outdoor unit.
XAfter tracking, you can use indoor unit control and other menu.
XFor tracking, refer to [System Settings] [Tracking] (Refer to page 148~152)
Connecting OnOff controller & outdoor unit
Starting DMS2.5
Access to DMS2.5 & Login
Address bar
If DMS2.5 time does not set as the current time, DMS2.5 may cause malfunction
when using Schedule or control logic management.

E-15
1Run internet explorer on your computer.
2Enter IP address (https://192.168.0.100) on the address bar, and then press [ENTER].
X If it is the first access to DMS2.5, “Install Microsoft Silverlight” message will be
displayed.
- The message will not appear if Microsoft Silverlight have already installed.
If the message window and login screen does not appear, check PC setting status.
1) At initial access, security certificate warning popup message will appear as shown.
This message appears since DMS2.5 used the certificate of its own, so it will not
appear if DMS2.5 certificate is registered on web browser. DMS2.5 certificate
must be registered because the message will appear every time and it is not safe
for security if it is not registered. Also, it should be registered to all PCs that are
connecting to DMS2.5.
You must stop connecting due to security problem if the message appears
even if you registered DMS2.5 certificate.
2) Registering DMS2.5 certificate on web browser
A. Select ‘Content’ tap in ‘Tools’
£ ‘Internet options’, and click ‘Certicates’.

E-16
B. Select ‘Trusted Root Certication Authorities’ and click ‘Import’.
C. Click ‘Next’.
D. Select ‘Browse’ and nd DMS2.5 certicate, and click ‘Next’. DMS2.5 certicate can
be downloaded from [System environment setting].
Starting DMS2.5 (Continued)

E-17
E. Select ‘Place all certicates in following drive’ and click ‘Next’.
F. Click ‘Finish’, and click ‘Yes’ when security warning appears.
3Click [Run] and continue installation.
XAccess to DMS2.5 again after installation.

E-18
Starting DMS2.5 (Continued)
4Enter ID and password when DMS2.5 main web page
appears.
Then click [LOGIN].
XThe default DMS2.5 user ID is 'admin' and password is
'ac0530'.
XDepending on authorization settings which set by the
administrator, access to some functions may be restricted.
XTo edit user authorization, refer to [System Settings]
[User authorization management]. (Refer to page 112)
Note XOnly authorized users can access to web page.
XFewer than 5 concurrent users are recommended
because connection speed may slow down.
XDMS2.5 manager should change ID and password for
security and management. (Refer to page 110)
XLogout: To log out, click [LOGOUT] on the top of the
menu.
Silverlight will run normally with Windows 7 or later version.
With former version of Windows, DMS2.5 may not operate
normally.
4

E-19
Logged-in User with No Authorization
1When the screen above appears, ask for manager.
XDepending on control authorization setting, there can be
a user who does not have control authorization.
X
Above screen will appear when the logged-in user does
not have control authorization.

Devices controlled and monitored by DMS2.5
Control and Monitoring
Type Display Remote controller
(Controlling range) Type Display Remote controller (Controlling range)
Indoor
unit
display
icon
DI
(Digital
Input)
display icon
ERV
display
icon
DO
(Digital
Output)
display icon
AHU
display
icon
Hydro Unit HT,
display icon
ERV PLUS
display
icon
FCU Kit
display
icon
Hydro
Unit,
Single EHS
display
icon
DVM CHILLER
display icon
Fresh duct
display
icon
E-20