Samsung Galaxy S6 edge Parts list manual

Easy2Fix –Replacement Guide
LCD REPLACEMENT GUIDE
FOR SAMSUNG GALAXY S6 Edge

1
Easy2Fix –Replacement Guide
What’s in the box:
LCD & Digitizer Assembly x1
Repair Tool kit x1
Screen Protector x1
Official store : www.krnetshop.com
CS Contact : [email protected]
C o p y r i g h t ©2 0 1 5 by Kr- n e t L i m i t e d

2
Easy2Fix –Replacement Guide
Step 1
Place the phone down
Step 2
Need to use a blow dryer/hair dryer
to reheat the adhesive glued at the
back of rear panel of the phone. So
once that is done, the adhesive
should be melted and unstruck with
the phone
Once the above action is taken,
need to carefully slip in the plastic
pick in between the rear panel and
the phone assembly
Step 3
Slip around the edge by using the
plastic pick to remove the adhesive
away from the rear panel
*Need to pay extra attention and
slip the pick because if put too
much physical force, the panel may
crack by accident

3
Easy2Fix –Replacement Guide
Step 4
After went around the top, left and
bottom side of the edge of the
panel by using the pick, you will be
able to see the adhesive left-over
Step 5
After some cleaning, the adhered
panel should be separates
successfully from the rest of the
phone assembly
Step 6
Need to remove the remain old
adhesive as they will not useable
anymore later on

4
Easy2Fix –Replacement Guide
Step 7
Need to use the screwdriver to
unscrew the Phillips #00 Screw at
the top from the phone
Step 8
Use the plastic opening tool to
carefully slip in between the edge of
the mid-frame and the LCD, then
you should be able to remove the
LCD easily

5
Easy2Fix –Replacement Guide
Step 9
Now the mid-frame and the LCD
with motherboard assembly are
separated with each other
Step 10
Carefully disconnect all the
connector from the motherboard by
using the Spudger
Step 11
Disconnect the ear speaker flex

6
Easy2Fix –Replacement Guide
Step 12
Unplug the LCD flex connector,
also disconnect the home button
connector (The little black flip door
at the middle)
Step 13
Disconnect the two button
connection wires from the
motherboard
Step 14
Need to remove the microphone at
the top from the display assembly

7
Easy2Fix –Replacement Guide
Step 15
Hold the motherboard up and
remove it from the phone, also we
need to remove the bottom wired
connector from the bottom of the
motherboard
Step 16
Take out the battery by using the
plastic pick and go around from
battery edge, remember to be real
gentle to slip it in between the
battery and the phone assembly. As
the battery was struck down with
strong adhesive

8
Easy2Fix –Replacement Guide
Step 17
To remove the bottom
motherboard, use the screwdriver
to unscrew the two Philip #00 from
the board (The red circle ones)
Step 18
Use the tweezer to detect the
bottom motherboard from the
phone assembly
Step 19
Use your finger to carefully take out
the board entirely

9
Easy2Fix –Replacement Guide
Step 20
Need to re-heat the LCD by using a
blow dryer/hair dryer, this is to
unstruck the adhesive at the
bottom of the LCD with the
digitizer, then carefully slip the
plastic pick in between the LCD and
the digitizer, and move around the
edges until the LCD come off
Step 21
Need to peel off the digitizer gently
from the frame, also need to
remove the home key on the frame
*Be extra careful to take out the
home key, because the flex cable is
very fragile
Step 22
To reassemble your device, follow
the above instructions in reverse
order

10
Easy2Fix –Replacement Guide
Notice/Warning:
KR-NET DOES NOT ACCEPT ANY LIABILITY FOR DAMAGE, OR INJURY
CAUSED, WHILE YOU ARE FOLLOWING OUR REPLACEMENT GUIDES.
WE MAKE NO REPRESENTATIONS, WARRANTIES, OR CONDITIONS
OF ANY KIND, EXPRESS OR IMPLIED. UTILIZING THESE GUIDES TO
HELP ASSIST YOU IN REPAIRING YOUR MOBILE DEVICES WILL VOID
YOUR WARRANTY. KR-NET STRICTLY PROHIBITS ALTERING OR
MODIFYING OUR REPLACEMENT GUIDES FOR COMMERCIAL USE,
REPRODUCTION, OR PUBLICATION.