Samsung SVR-1630 User manual

SVR-1630
Installation
Manual

Caution
This device is registered as an EMC for commercial purposes. Vendors and users should be aware of this
EMC registration. If this device is sold or purchased by mistake, the device will need to be altered for
domestic use.
FCC Compliance Statement
Caution : Any changes or modifications in the construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority to operate the
equipment.
NOTE : This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at their own expense.
Warning
This is a class A product. In a domestic environment this product may cause radio interference, in which
case the user may be required to take suitable correction measures
Warning
1. If the built-in Lithium battery is replaced by another type of battery, there is a risk of explosion.
Therefore it is necessary to replace the battery with the same type of battery or an identical one. In
addition, be sure to dispose of worn-out batteries properly because they may cause environmental
pollution.
2. Do not throw the battery into a fire, or heat , disassemble, cut or discharge it because those treatments
can cause the failure of device.
3. Do not recharge the remote controller’s battery.

Cautions
1. Do not put a large monitor or other heavy objects on the SVR-1630 when using it.
2. The SVR-1630 is designed for indoor use and therefore is not waterproof or dampproof. Therefore
before use it is necessary to fully understand the operating environment requirements detailed in the user
manual, and to use the device within the scope of the terms of service. For cleaning the device, wipe it
gently using a clean and dry cloth.
3. The SVR-1630 can be damaged by electric shock. Be careful to use AC power of 110V ~ 220V.
4. The SVR-1630 can be damaged by physical shock because it contains an HDD. Therefore, do not
throw or drop the device.
5. The SVR-1630 is made of metal. If it is thrown at anybody it may cause harm. Install the device in a
safe place out of the reach of children.
6. If the SVR-1630 does not operate correctly, do not disassemble it without authorization. Contact your
local agency for after sales service. The warranty will become invalid if it is disassembled without
authorization.
7. The SVR-1630 can transfer images in real time via a network and can be used for monitoring,
depending on the installation location. Therefore check the laws in the relevant area carefully, and then
install the device in such a way as not to infringe any of its laws.

SVR-1630 Contents
4
2004. 07. 2004 (v 1.0)
Samsung Techwin
Contents
Executive Summary ......................................................................................................................... 7
1. Main Features of the SVR-1630............................................................................................. 7
2. Component Check................................................................................................................... 8
3. Description of the Front/Rear View......................................................................................10
Installation and Connection.......................................................................................................... 12
4. Basic Connection and Start-up.............................................................................................12
4.1 Overall Layout................................................................................................................12
4.2 Connecting a Camera....................................................................................................13
4.3 Connecting a Monitor ....................................................................................................14
4.3.1 Connecting a CCTV Monitor .................................................................................14
4.3.2 Connecting a VGA Monitor.................................................................................... 14
4.4 Connecting Audio........................................................................................................... 15
4.5 Supplying Power and Running...................................................................................... 16
5. OSD Menu Configuration and Control.................................................................................17
5.1 Menu Configuration .......................................................................................................17
5.2 Word Input......................................................................................................................18
6. Remote Controller Setup and Basic Control .......................................................................19
6.1 Setting ID of SVR-1630.................................................................................................19
6.2 Selecting SVR-1630 ......................................................................................................20
6.3 Operable Range of the Remote Controller ..................................................................20
6.4 Loading batteries into the remote controller ......................................................20
7. SVR-1630 Installation Example............................................................................................22
7.1 Basic Configuration........................................................................................................ 22
7.2 Advanced Configuration................................................................................................22
7.3 External Storage & Backup Configuration....................................................................23
7.4 Internet/Intranet Configuration......................................................................................23
8. SVR-1630
Basic Setting ................................................................................................24
8.1 Viewing Images..............................................................................................................24
8.2 Setting Date and Time...................................................................................................25
8.2.1 Time Zone...............................................................................................................25
8.2.2 Daylight Saving.......................................................................................................25
8.2.3 Sync with NTP........................................................................................................25

Contents SVR-1630
Samsung Techwin
2004. 07. 2001 (v 1.0)
5
8.2.4 Time Format ...........................................................................................................26
8.2.5 Date Mode..............................................................................................................26
8.2.6 Time.........................................................................................................................26
8.2.7 Apply Date/Time.....................................................................................................26
8.3 Setting Recording Conditions .......................................................................................26
8.3.1 Configuration Status............................................................................................... 27
8.3.2 Channel Status....................................................................................................... 27
8.3.3 Record Rate/Quality...............................................................................................28
8.3.4 Rate (fps) ................................................................................................................ 28
8.3.5 Quality.....................................................................................................................28
8.3.6 Audio Record..........................................................................................................28
8.3.7 Apply ....................................................................................................................... 28
9. Using Input/Output Terminals...............................................................................................29
9.1 Connecting and Configuring the Sensor......................................................................30
9.1.1 Specification............................................................................................................ 30
9.1.2 Connecting Sensor Input.......................................................................................30
9.1.3 Setting Sensors......................................................................................................31
9.2 Connecting and Setting Relay Output.......................................................................... 32
9.2.1 Specification............................................................................................................ 32
9.2.2 Connecting to Relay Output Terminal...................................................................32
9.2.3 Configuring Relay Out............................................................................................33
9.3 Connecting and Configuring Serial Communication Ports.......................................... 34
9.3.1 Connecting Serial Communication Ports for Pan/Tilt/Zoom................................34
9.3.2 Serial Communication Port Connection Layout...................................................35
9.3.3 Serial Communication Port Figure........................................................................36
9.3.4 Configuring a Serial Port........................................................................................37
9.4 Connecting an External Device to a Serial Port .......................................................... 38
9.4.1 Connecting Text Input Devices (ATM / POS / Access Control)........................... 38
9.4.2 Configuring Serial Setup (COM1).........................................................................39
9.4.3 Configuring Text......................................................................................................40
9.5 Connecting a USB Device............................................................................................. 41
9.6 Connecting Video In/Out...............................................................................................42
10. HDD.................................................................................................................................... 43
10.1 Adding and Replacing HDDs on the HDD Rack..........................................................43
10.1.1 Available HDDs ......................................................................................................43
10.1.2 Mounting an HDD...................................................................................................43

SVR-1630 Contents
6
2004. 07. 2004 (v 1.0)
Samsung Techwin
10.2 Adding and Replacing External Storage Device..........................................................46
10.2.1 IEEE1394 Port........................................................................................................46
10.2.2 Connecting IEEE1394 Device............................................................................... 46
10.3 Registering and Formatting an HDD............................................................................47
11. Remote Monitoring and Control........................................................................................ 48
11.1 Connecting via Ethernet................................................................................................48
11.2 Configuring an SVR-1630 Network ..............................................................................49
12. Using the SVR Manager ................................................................................................... 50
12.1 PC System Requirements for running the SVR Manager...........................................50
12.2 Installing the SVR Manager ..........................................................................................50
12.3 Uninstalling the SVR Manager......................................................................................52
12.4 Configstation ..................................................................................................................52
12.5 Monitor............................................................................................................................53
12.6 Playback.........................................................................................................................54
Appendix.......................................................................................................................................... 55
1. HDD........................................................................................................................................56
1.1 Fundamental Notions & Terms......................................................................................56
1.1.1 SVR-1630
Storing Structure (VFS2).................................................................56
1.1.2 Backup....................................................................................................................56
1.1.3 Disk Manager .........................................................................................................57
1.2 Replacing HDDs ............................................................................................................ 58
1.2.1 Checking HDDs......................................................................................................58
1.2.2 When the primary disk fails ................................................................................... 58
1.2.3 When an auxiliary disk fails...................................................................................58
1.3 Keeping Data..................................................................................................................59
1.3.1 Backup....................................................................................................................59
1.3.2 Separating and Preserving HDDs......................................................................... 60
1.3.3 Cautions..................................................................................................................60
2. Changing Video Type............................................................................................................61
3. Using CD-Rom....................................................................................................................... 62
3.1 CD- ROM DISC Components....................................................................................... 62
3.2 Preparation.....................................................................................................................62
3.3 Reading the User Manual in CD-ROM.........................................................................62
4. Specification...........................................................................................................................63

Executive Summary SVR-1630
Samsung Techwin
2004. 07. 2001 (v 1.0)
7
Executive Summary
1. Main Features of the SVR-1630
The SVR-1630 is a new concept DVR, saving the video inputs, audio, text data and alarm data of 16
channels in two built-in HDDs, with its main features described below.
□16-Channel Video Input Support
□1 ChannelAudio Recording and Playback
□Max. 240fps Recording
□Real-time monitoring (30fps per channel)
□Built-in software multiplexer for 16-Channel split monitoring
(1 / 2x2/3x3 /4x4 Screen Mode Support)
□Up to 4TB Storage Capacity (Expansion using IEEE 1394 Port)
□Text data recording by interlocking with ATM/POS devices
□16 Sensor Inputs and 4 Interlocked Relay Outputs
□Hardware Motion Detection (64 Section)
□Backup using IEEE1394 and Network
□PTZ control
□Easy-to-use Color Graphic OSD
□Dynamic IP support
□IR Remote Controller
□Remote Management Software provided (SVR Manager)
□Dual CCTV Monitor support (3 Normal, 1 Spot)
□VGAmonitor support
□CD-RW backup support (option)

SVR-1630 Executive Summary
8
2004. 07. 2004 (v 1.0)
Samsung Techwin
2. Component Check
Please checkthe package to make sure that you receive all the accessories, including the components shown below.
1. SVR-1630 (1EA) 2.AC Power Cord (1EA)
3. CD-ROM (Including SVR Manager) (1EA)
4. Remote Controller (1EA)
5. Guide (2EA)
6. HDD Fixing KIT (1SET)
7. 19” RACK FIXING KIT (1SET)
8. HDD EARTH CABLE (1EA)

Executive Summary SVR-1630
Samsung Techwin
2004. 07. 2001 (v 1.0)
9
9. HDD Removable Rack KIT(1SET)

SVR-1630 Executive Summary
10
2004. 07. 2004 (v 1.0)
Samsung Techwin
3. Description of the Front/Rear View
SVR-1630 Front View
(1) Power Switch
(2) HDD Removable Rack
(3) Function Buttons
(4) Channel Buttons
(5) Status LED
(6) Jog Shuttle for Search and Playback
(7) Function Switch
(8)Play and Search Button
(9) Search/Preset Switch
(10) Remote Controller Receiver
(11) USB Connector
(12) IEEE 1394 Connector
(13)
Bracket fixing hole for rack mount

Executive Summary SVR-1630
Samsung Techwin
2004. 07. 2001 (v 1.0)
11
SVR-1630 Rear View
(14) BNC connector for video output
(15) BNC connector for video input
(16) BNC connector for Monitor Aoutput
(17) BNC connector for Monitor Ainput
(18) Ethernet connector
(19) GND
(20) Input/output terminal for RS232 & RS422/485
(21) IEEE 1394 connector
(22) S-VHS connector for Monitor Aoutput
(23) Input/output terminals for sensor, relay and serial
(24) RS232 connector (9Pin D-Sub)
(25) Connector for VGAmonitor
(26) RCA connector for audio input/output
(27) AC power input connector

SVR-1630 Installation and Connection
12
2004. 07. 2004 (v 1.0)
Samsung Techwin
Installation and Connection
4. Basic Connection and Start-up
4.1 Overall Layout
(1) The devices that can be connected to the SVR-1630 are described below. See each relevant section in
the installation manual for the contents on the figure.

Installation and Connection SVR-1630
Samsung Techwin
2004. 07. 2001 (v 1.0)
13
4.2 Connecting a Camera
(1) Connect a camera to the SVR-1630 using the coaxial cable as shown in the figure below.
<Note>
1. The input video type should be either NTSC or PAL. Do not use both types at the same time.
2. Automatic setting of 75Ωterminal resistance
Two video terminals are internally connected. A terminal resistance of 75Ω exists when
only one terminal is connected. Hi-z exists when both terminals are connected.
See “9.6. Connecting Video In/Out ” on the page 42.
3. The Input Video Type (NTSC/PAL) is automatically recognized when the device runs.
For the recognition sequence, camera number 1 is recognized first, and then the sequence is decided
according to the camera signal type that is first detected, from cameras no. 1 to 16. When no cameras
are connected, the internal jumper setting is applied. To change the internal jumper, see page 61,
Appendix “2. Changing Video Type”

SVR-1630 Installation and Connection
14
2004. 07. 2004 (v 1.0)
Samsung Techwin
4.3 Connecting a Monitor
4.3.1 Connecting a CCTV Monitor
(1) Connect a monitor to the SVR-1630 using the coaxial cable as shown in the figure below.
4.3.2 Connecting a VGA Monitor
(1) Monitor Outuput A can output to VGA. For better definition quality, connect Monitor A to the VGA
Monitor as shown in the figure below.
<Note>
1. The SVR-1630 monitor outputs are divided into A (Normal) and B (Spot). If only one monitor is
connected, connect Monitor A.
2. For Monitor Output A, the same video output is transferred to two BNC connectors and an S-VHS
connector.

Installation and Connection SVR-1630
Samsung Techwin
2004. 07. 2001 (v 1.0)
15
4.4 Connecting Audio
(1) Connect an audio signal to the SVR-1630 using the RCA cable as shown in the figure below.

SVR-1630 Installation and Connection
16
2004. 07. 2004 (v 1.0)
Samsung Techwin
4.5 Supplying Power and Running
(1) Connect the power cable as shown in the figure below.
<Note>
1. Connect the power cable, press the power switch, and the device starts booting.
2.Press and release the power switch while SVR-1630 is ON, the following windows are displayed
according to the system setting after 4 seconds.
When there isAdmin password in “System Setup”
The dialogue box asking to enter the admin password is appeared. Enter the password, and the power is
off.
When there isnoAdmin password in “System Setup”
The dialogue box asking “Yes” or “No” is appeared. Select “Yes”, and the power is off.
3. For turning the power on again, press the power switch.

Installation and Connection SVR-1630
Samsung Techwin
2004. 07. 2001 (v 1.0)
17
5. OSD Menu Configuration and Control
5.1 Menu Configuration
Press the [MENU] button on the keypad on the front panel, and the system changes to the SVR-1630
Setup mode. The OSD Menu is displayed as shown in the figure below. The Jog/Shuttle on the menu is
controlled as described in the figure below.
①Main Menu
② Sub-menu
③ Setup Dialogue Box

SVR-1630 Installation and Connection
18
2004. 07. 2004 (v 1.0)
Samsung Techwin
(1) Main Menu : The selected tab is shown in blue and the related sub-menus will be shown below the tab.
To move to the previous/next Main Menu Tab, use the [
◀/▶ ] arrow buttons. To move to the relevant sub-
menu, press the [ENTER] or [▼] buttons.
(2) Sub-menu :
The selected sub-menu is shown in blue and the related setting page will be shown to the
right of the sub-menu. Use the [▲/▼] arrow buttons to move within the sub-menu list. To move to the setting
page, press the [ENTER] button. To go to the Main Menu, press the [ESC] button.
(3) Setting Page :
The selected item is shown with a circle to the left of its name. The field to set values is
shown in gray. To move within each page, use the [
◀/▶ ] or [▲/▼] arrow buttons. Press the [ENTER] button
to change the value of a setting. The setting values of items are divided into text (including letters and
numbers) and numbers. When the setting value is a word, a dialogue box to edit the word will open. When the
setting value is a number, it should be set by using the [
◀/▶ ] or [▲/▼] arrow buttons. After the value is set,
press the [ESC] button. To go to the Main Menu, press the [ESC] button.
5.2 Word Input
Select a value using the [▲/▼] buttons. Press the [ENTER] button to confirm the selected value.

Installation and Connection SVR-1630
Samsung Techwin
2004. 07. 2001 (v 1.0)
19
6. Remote Controller Setup and Basic Control
6.1 Setting ID of SVR-1630
When controlling several SVR-1630s with one remote controller, multiple DVRs can be set by one remote
controller. Set the remote controller ID as described below.
(1) Press the [MENU] button.
(2)
Select “System” by using the [ ▶ ] button and press the [ENTER] or [▼] button.
(3) Select “Etc.” using the [▼] button and press the [ENTER] button.
(4) Select “Remote ControlID,” and press the [ENTER] button.
(5) Select a value using the [
◀/▶ ] buttons and press the [ESC] button.
(6) Press the [ESC] button to return to Monitor mode.

SVR-1630 Installation and Connection
20
2004. 07. 2004 (v 1.0)
Samsung Techwin
6.2 Selecting SVR-1630
Multiple DVRs with different IDs can be controlled by one remote controller. To select a specific SVR-1630 ,
press the ID button of the remote controller. When the DVR ID matches the remote controller ID, the LED on
the front of the
SVR-1630 lights up and a buzzer sounds for two seconds.
<Note>
Up to 16 Remote Controller IDs are supported, which consist of two digits from 1 to 4.
ID Key Sets ID Key Sets ID Key Sets ID Key Sets
ID1-1 1 , 1 ID2-1 2 , 1 ID3-1 3 , 1 ID4-1 4 , 1
ID1-2 1 , 2 ID2-2 2 , 2 ID3-2 3 , 2 ID4-2 4 , 2
ID1-3 1 , 3 ID2-3 2 , 3 ID3-3 3 , 3 ID4-3 4 , 3
ID1-4 1 , 4 ID2-4 2 , 4 ID3-4 3 , 4 ID4-4 4 , 4
6.3 Operable Range of the Remote Controller
6.4 Loading batteries into the remote controller
The remote controller uses only AAA-type batteries. The batteries are loaded into the remote controller as
described below.
1.
Remove the battery cover.
2. Check battery polarity and insert batteries.