Samsung OfficeServ 7030 User manual

Ed. 01
OfficeServ 7030
Installation Manual

COPYRIGHT
This manual is proprietary to SAMSUNG Electronics Co., Ltd. and is protected by copyright.
No in ormation contained herein may be copied, translated, transcribed or duplicated or any commercial
purposes or disclosed to the third party in any orm without the prior written consent o SAMSUNG Electronics
Co., Ltd.
TRADEMARKS
is the trademark o SAMSUNG Electronics Co., Ltd.
Product names mentioned in this manual may be trademarks and/or registered trademarks o their respective
companies.
This manual should be ead and used as a guideline fo p ope ly installing and ope ating the p oduct.

This manual may be changed or the system improvement, standardization and other technical reasons without prior
notice.
I you need updated manuals or have any questions concerning the contents o the manuals, contact our Document
Cente at the ollowing address or Web site:
Add ess: Document Cente 2nd Floo Jeong-bo-tong-sin-dong. Dong-Suwon P.O. Box 105, 416, Maetan-3dong
Yeongtong-gu, Suwon-si, Gyeonggi-do, Ko ea 442-600
Homepage: http://www.samsungdocs.com
© 2008 SAMSUNG Elect onics Co., Ltd. All ights ese ved.

OfficeSe v 7030 Installation Manual
INTRODUCTION
Pu pose
OfficeServ 7030 is the most suitable system for small offices with 10 to 20 subscribers
circuit line. This manual describes the prerequisite for the installation of the OfficeServ
7030 system as well as how to install inspect and operate the system.
Document Content and O ganization
This document consists of 7 chapters and abbreviations as follows:
CHAPTER 1. Befo e Installing
This chapter describes the checklists (installation site grounding & power conditions etc.)
which should be inspected before installing the OfficeServ 7030 system. This chapter also
describes the items included in the OfficeServ 7030 package and the installation procedure.
CHAPTER 2. Mounting and Replacing the Boa ds
This chapter describes how to mount/replace various boards to/from the OfficeServ 7030
system.
CHAPTER 3. Installing the System
This chapter describes how to install an OfficeServ 7030 on the wall if necessary
depending on the installation environment.
CHAPTER 4. Connecting the Powe
This chapter describes how to connect the power to the OfficeServ 7030 system.
CHAPTER 5. Connecting the C.O. Line
© SAMSUNG Electronics Co., Ltd. I

INTRODUCTION
This chapter describes how to connect the C.O. lines to the OfficeServ 7030 system.
II © SAMSUNG Electronics Co., Ltd.

OfficeSe v 7030 Installation Manual
CHAPTER 6. Connecting the Stations and Additional Equipment
This chapter describes how to connect various stations and additional equipment
(analog/digital phones door phones door locks etc.) to the OfficeServ 7030 system.
CHAPTER 7. Sta ting the System
This chapter describes the items to check before starting the OfficeServ 7030 system as
well as the procedure for starting the system and the procedure for testing whether the
system is operating normally after startup.
ABBREVIATION
Describes the abbreviations frequently used in this document.
Conventions
The following types of paragraphs contain special information that must be carefully read
and thoroughly understood. Such information may or may not be enclosed in a rectangular
box separating it from the main text but is always preceded by an icon and/or a bold title.
WARNING
Provides in ormation or instructions that the reader should ollow in order to avoid
personal injury or atality.
CAUTION
Provides in ormation or instructions that the reader should ollow in order to avoid
a service ailure or damage to the system.
CHECKPOINT
Provides the operator with checkpoints or stable system operation.
NOTE
© SAMSUNG Electronics Co., Ltd. III

INTRODUCTION
Indicates additional in ormation as a re erence.
IV © SAMSUNG Electronics Co., Ltd.

OfficeSe v 7030 Installation Manual
Refe ence
OfficeSe v 7030 System Desc iption
This manual introduces the OfficeServ 7030 and describes the system information
(hardware configuration specification functions etc.) necessary for this system.
OfficeSe v 7030 Se vice Manual
This manual provides an overview specification hardware circuit configuration and
feature of the system.
OfficeSe v 7030 P og amming Manual
This manual describes how to use the MMC program to change the setting of the
OfficeServ 7030 system from the phone.
Revision Histo y
EDITION DATE OF ISSUE REMARKS
00 06. 2008. First Dra t
01 07. 2008. - Functions o BRI/MEM/LAN LED are changed.
- Cautions are added.
.Turning o power switch a ter dismounting MEM
.Checking MEM LED be ore power o
.Checking LAN cable during lighting LAN LED on
.Caution or using extension cable
© SAMSUNG Electronics Co., Ltd. V

INTRODUCTION
VI © SAMSUNG Electronics Co., Ltd.
This page is intentionally left blank.

OfficeSe v 7030 Installation Manual
SAFETY CONCERNS
For product safety and correct operation the following information must be given to the
operator/user and shall be read before the installation and operation.
Symbols
Caution
Indication o a general caution
Rest iction
Indication or prohibiting an action or a product
Inst uction
Indication or commanding a speci ically required action
© SAMSUNG Electronics Co., Ltd. VII

SAFETY CONCERNS
Wa ning
Caution fo g ounding
- Do not connect the O iceServ 7030 system's grounding wire to the building's
power conduit.
- The power and grounding installation should comply with the local standard;
all related works should be conducted according to the local standard.
- External grounding is required to prevent bodily injuries or system damages
rom lightning, static electricity or voltage surge.
- Unplug the AC power cord be ore connecting the grounding wire. Failure to do
so may cause bodily injury.
- The O iceServ 7030 system should be connected to a protective-ground
outlet.
- The GND in the back panel o the O iceServ 7030 system should be grounded.
Using double-pole/neut al fusing
Do not attempt to repair the system a ter only removing the use rom the neutral
line, doing so may cause electric shock. I the repair is required, unplug the
system's power cord be ore proceeding.
AC powe connection est iction
Connect the system’s AC power to a separated AC outlet. I the AC power is used
together with other equipments, a system ailure or ire may occur due to static
electricity and/or voltage drop.
Caution fo using expansion cabinet
Do not put the expansion cabinet on top o basic cabinet horizontally. Doing so
may cause a system ailure or ire due to rising internal heat o the basic cabinet.
VIII © SAMSUNG Electronics Co., Ltd.
WARNING

OfficeSe v 7030 Installation Manual
Caution fo powe supply when mounting the boa d
Check i the cabinet power is turned o when mounting the board. Inserting or
removing a board while the power is turned on may damage the board.
© SAMSUNG Electronics Co., Ltd. IX

SAFETY CONCERNS
Caution fo the connection of the g ound cable
Unplug the AC power cord be ore connecting the ground cable. Any attempt to
connect the ground cable while the power cord is connected may cause severe
bodily injury.
Caution
Caution fo installation
Only a trained service sta may install the O iceServ 7030 system.
The equipment is intended to be installed only in a RESTRICTED ACCESS
LOCATION.
Leakage cu ents caused by inging voltage–g ounding installation
inst uctions
1. A supplementary equipment grounding conductor should be installed between
the system and the earth in addition to the de ault equipment grounding
conductor provided in the power supply cord.
2. The size o the supplementary equipment grounding conductor should not be
smaller than the ungrounded branch-circuit supply conductors.
The supplementary equipment grounding conductor should be connected to
the product rom the provided terminal, and connected to the earth in order to
maintain the earth connection when the power supply cord is unplugged.
The connection o the supplementary grounding conductor to the earth should
comply with the appropriate rules or terminating bonding jumpers, including
the National Electrical Code (Article 250, Part K), the ANSI/NFPA 70 and the
Canadian Electrical Code, C22.1 (Part 1, Article 10). The termination o the
supplementary grounding conductor may consist o building steel, o a metal
electrical raceway system or o any grounded item permanently and reliably
connected to the grounded electrical service equipment.
X© SAMSUNG Electronics Co., Ltd.
CAUTION

OfficeSe v 7030 Installation Manual
3. Bare, covered or insulated grounding conductors are acceptable. A covered or
insulated conductor must have a uni orm outer inish, either green or green
with yellow stripes.
Sepa ation of TNV and SELV-Pluggable A
The separate protective grounding terminal provided with this product should be
permanently connected to the earth. (Instruction)
© SAMSUNG Electronics Co., Ltd. XI

SAFETY CONCERNS
Telephone line co d
To reduce the risk o ire, use only No. 26 AWG or larger (e.g., 24 AWG), UL
Listed or CSA Certi ied Telecommunication Line Cord.
P ohibition of metal accesso ies
Do not wear metal accessories such as rings and watches to prevent electric
damages to the system.
AC powe connection est iction
Do not share the AC power o the O iceServ 7030 system or the AC power o the
external UPS with other devices.
Checking MEM LED befo e powe off
Don’t turn o the power during blinking MEM LED. It may cause mal unction o
system. I you want to turn o power, turn o power switch a ter dismounting
MEM with ‘Key MMC 817 MEM UMOUNT’.
Checking powe -off
Check i the cabinet power is turned o when mounting the board. Inserting or
removing a board while the power is turned on may damage the board.
Boa d eset
New settings are applied only a ter the board is reset. The system may
mal unction i the board is not properly initialized.
Caution fo Installation
Only a trained service sta may install the O iceServ 7030 system.
XII © SAMSUNG Electronics Co., Ltd.

OfficeSe v 7030 Installation Manual
Tu ning off powe switch afte dismounting MEM
You should dismount MEM be ore turning o power switch. Use ‘Key MMC 817
MEM UMOUNT’ when dismounting MEM.
© SAMSUNG Electronics Co., Ltd. XIII

SAFETY CONCERNS
Checking LAN cable du ing lighting LAN LED on
LAN LED lights on in case o being installed EPM board although LAN cable is
not connected. Check i LAN cable is connected during lighting LAN LED on.
Caution fo using extension cable
Check i extension cable is connected during operation. The expansion cabinet
may mal unction i extension cable is not connected during operation. In that
case, you should connect extension cable again and restart expansion cabinet.
XIV © SAMSUNG Electronics Co., Ltd.

OfficeSe v 7030 Installation Manual
© SAMSUNG Electronics Co., Ltd. XV
This page is intentionally left blank.