Sangean DPR-99 Plus User manual

381SF0D-A
DAB Plus/FM RDS digital portable radio
with built-in battery charger
Operating instruction
Mode d’emploi
Instruccions de manejo
Gebruiksaanwijzing
Bedienungsanleitung
GB
F
E
NL
D
All manuals and user guides at all-guides.com
all-guides.com

1
Contents
Controls ............................................................................... 2-3
Batteryoperation ................................................................ 4-5
Using theAC adaptor ............................................................ 5
Operating your radio -DAB .................................................. 6
Selecting a station -DAB ..................................................... 7
Secondary services -DAB ................................................... 7
Display modes -DAB ........................................................... 8
Finding new stations -DAB .................................................. 9
Signal strength display -DAB ............................................. 9
Manual tuning - DAB .......................................................... 10
Autoselect-DAB ................................................................. 10
Dynamic range control - DAB ............................................ 11
Station order setup -DAB ............................................. 12-13
Operating your radio - FM .................................................. 14
Manual tuning - FM ............................................................. 15
Display modes - FM ........................................................... 16
Presettingstations .............................................................. 17
Stereo / Mono setting - FM ................................................ 18
Scan sensitivity setting - FM .............................................. 19
Softwareversion .................................................................. 20
Systemreset ........................................................................ 20
Headphonesocket ............................................................. 21
Displaybacklight ................................................................. 21
Afew words about batteries ........................................... 22-23
General.................................................................................. 24
Specifications ...................................................................... 25
Circuitfeatures .................................................................... 25
All manuals and user guides at all-guides.com

2
GB
Controls
1. Loudspeaker
2. Band button
3. LCD display
4. Charge LED indicator
5.Auto Tune button 1
6. Menu / Info button
7. On / Off button
8. Volume control
9. Tuning Up / Down buttons
10. Select button
11. Preset buttons
(Front)
All manuals and user guides at all-guides.com

3
Controls
(Back)
12. Battery compartment
13. Telescopic aerial 14. Headphone socket 15. DC jack socket
All manuals and user guides at all-guides.com

4
GB
Battery operation using alkaline batteries
1. Remove the battery cover on the back of the unit by sliding the cover
in the direction of the arrow.
2. Insert six LR6 (AAsize) alkaline batteries into the spaces in the
compartment. Take care to ensure all batteries are inserted with the
correct polarity as shown inside the battery compartment.
3. Slide the battery switch to the Alkaline position and then replace the
battery cover.
Important: when using alkaline batteries the battery switch must
be placed in the alkaline position. Failure to do so could result
in serious damage to the batteries or radio.
Reduced power, distortion and a 'tuttering' sound are all signs that
the batteries may need replacing.
If the radio is not to be used for any extended period of time it is
recommended that the batteries are removed from the radio.
We would recommend for economy that the radio is used via the
AC adaptor whenever possible with battery operation for occasional
or stand-by use only. If extended listening using batteries is
anticipated, then the use of rechargeable batteries is recommended.
Battery operation using rechargeable batteries
1. Remove the battery cover on the back of the unit by sliding the cover
in the direction of the arrow.
2. Insert six Rechargeable LR6 (AAsize) batteries into the spaces in
the compartment. Take care to ensure all batteries are inserted with
the correct polarity as shown inside the battery compartment.
The radio is designed to be used with Nickel Metal Hydride (NiMH)
rechargeable batteries.
3. Slide the battery switch to the Rechargeable position and then
replace the battery cover.
All manuals and user guides at all-guides.com

5
4. The charge indicator lights to show that the batteries are charging.
Batteries will be fully charged in around 7 hours.
Important: when using rechargeable batteries the battery switch
must be placed in the rechargeable position. Batteries will only
be charged when the radio is switched off and connected to the
AC adaptor.
Reduced power, distortion or your radio switching off by itself are all
signs that the batteries may need recharging.
If the radio is not to be used for any extended period of time it is
recommended that the batteries are removed from the radio.
IMPORTANT: The batteries should not be exposed to excessive heat
such as sunshine, fire or the like. After use, disposable batteries
should if possible be taken to a suitable recycling centre.
On no account should batteries be disposed of by incineration.
Using the AC adaptor
TheAC adaptor for use with the radio should provide 12 voltsDC output
at 1 amp, centre pin positive.
1. Insert the adaptor plug into theDC in socket on the left hand side of
your radio.
2. Plug the adaptor into a standard 13Amains socket outlet.
Whenever the adaptor is plugged in to the radio and switched on at
the mains the batteries are automatically disconnected. If the adaptor
is plugged in to the radio but not switched on then the radio will run
from the batteries if fitted.
The AC adaptor should be disconnected from the mains supply and
the radio when not in use.
IMPORTANT: The mains adaptor is used as the means of connecting
the radio to the mains supply. The mains socket used for the radio
must remain accessible during normal use. In order to disconnect the
radio from the mains completely, the mains adaptor should be
removed from the mains socket outlet completely.
All manuals and user guides at all-guides.com
all-guides.com

6
GB
Operating your radio - DAB
1. Carefully extend the telescopic aerial.
2. Press the On/Off button to switch on your radio. The display will
show “Welcome to Digital Radio” for a few seconds.
3. If this is the first time the radio is used a quick scan of Band III
DAB channels will be carried out, known as Auto-tune. The display
will show “Welcome to DAB”.
4.DuringAuto-tune, the lower line of the display shows a bar graph
indicating progress of auto-tune. If the radio has been used before,
then the last used station will be selected instead of the
Auto-tune process.
5. When theAuto-tune is completed the first station found
(in numeric-alpha order 0...9...A....Z) will be selected.
6. If the station list is still empty after the Auto-tune your radio will
display “No stations available”.
7. If no stations are found it may be necessary to relocate your radio to
a position giving better reception.
All manuals and user guides at all-guides.com

7
Selecting a station - DAB
1. The top line of the display shows the name of the station
currently selected.
2. Press either of the Tuning Up or Down buttons to scroll through the
list of available stations.
3. Press and release the Select button to select the station. The display
may show “Now tuning” while your radio finds the new station.
4. Adjust the Volume control to the required setting.
Note:
If after selecting a station the display shows “station not available”
it may be necessary to relocate your radio to a position giving
better reception.
Secondary services - DAB
1. Certain radio stations have one or more secondary services
associated with them. If a station has a secondary service
associated with it the display will show “>>” next to the station
name on the station list. The secondary service will then appear
immediately after the primary service as you press the
Tuning Up button.
2. Press the Select control to select the station.
All manuals and user guides at all-guides.com

8
GB
Display modes - DAB
Your radio has seven display modes forDAB radio:-
1. Press and release the Info/Menu button to cycle through the
various modes.
a.
b.
c.
d.
e.
f.
g.
Displays scrolling text messages
such as artist/track name, phone in
number, etc.
Displays type of station being
listened to e.g. Pop, Classic,
News, etc.
Displays name of theDAB multiplex
to which the current station belongs.
Displays current time and date.
Displays channel and frequency for
the station being listened to.
Displays audio type and bit rate for
the station being listened to.
Displays signal strength for the
station being listened to.
Scrolling text
Programme type
Multiplex name
Time and date
Channel and frequency
Audio type and bit rate
Signal strength
All manuals and user guides at all-guides.com

9
Finding new stations - DAB
As time passes new stations may become available. To find new
stations proceed as follows:-
1. Press and release the Auto Tune button, the display will show
“Fast scanning”. Your radio will perform a scan of the DAB III
frequencies. As new stations are found the station counter on the
right-hand side of the display will increase and stations will be added
to the list.
2. To carry out a full scan of the entireDAB Band III frequencies press
and hold down the Auto Tune button for more than 2 seconds and
then release. The display will show “Full scanning”. As new stations
are found the station counter on the right-hand side of the display will
increase and stations will be added to the list.
Signal strength display - DAB
1. Repeatedly press and release the Info button until the display shows
the signal strength.
2. Position your radio and carefully angle the telescopic aerial for best
reception using the signal strength display as a guide. Move your
radio around and position it so as to give maximum number of black
rectangles on the signal strength display. The clear unfilled rectangle
indicates the minimum signal level required for satisfactory reception.
3. Press the Info button to exit the signal strength display.
All manuals and user guides at all-guides.com

10
GB
Manual Tuning - DAB
Manual tuning allows you to tune directly to the variousDAB Band III
channels.
1. Press and hold the Select button until the display shows
“Manual tune”. Release the Select button.
2. Press either of the Tuning Up orDown buttons to select the required
DAB channel.
3. Press and release the Select button to select the required
DAB channel. The open bar in the middle shows you the minimum
signal strength needed for good DAB reception. The signal strength
bars will go up and down showing the changing signal strength as
you adjust the telescopic aerial on your radio.
4. When aDAB signal is found, the display will show the name of the
DAB multiplex.Any new radio stations found will be added to the list
stored in the radio.
5. Press and release the Select button to return to normal tuning.
Autoselect - DAB
As an alternative to pressing the Select button to select a station your
radio can be set so as to automatically select a station.
1. Press and release either of the Tuning Up or Down buttons a
few times, immediately press and hold down the Select button until
the display shows “Autoselect ON”.
2. Press the Tuning Up orDown buttons until the station you require is
visible on the display. After a few seconds your radio will
automatically select the station shown on the display.
3. To switch off autoselect press and release the Tuning Up or Down
buttons a few times, immediately press and hold down the Select
button until the display shows “Autoselect Off”.
All manuals and user guides at all-guides.com
all-guides.com

11
Dynamic Range Control (DRC) settings - DAB
DRC can make quieter sounds easier to hear when your radio is used in
a noisy environment.
1. Press the On/Off button to switch on your radio.
2. Press and hold in the Info/Menu button and the display will
show “Station order.”
3. Press the Tuning Up or Down buttons until the display
shows “DRC value”.
4. Press and release the Select button to enter adjustment mode.
5. Press the Tuning Up/Down buttons to select requiredDRC setting
(default is 0) .
DRC 0DRC is switched off, Broadcast DRC will be ignored.
DRC 1/2DRC level is set to 1/2 that sent by broadcaster.
DRC 1 DRC is set as sent by broadcaster.
6. Press and release the Select button to confirm the setting.
The display will return to normal tuning mode.
Note:
Not all DAB broadcasts are able to use theDRC function. If the
broadcast does not support DRC, then theDRC setting in the radio will
have no effect.
All manuals and user guides at all-guides.com

12
GB
Station order setup - DAB
This function enables you to choose how the stations are arranged
when selecting a station. There are four options available -
favourite station, alphanumeric, active station and prune stations.
Note: Your radio default station order is numeric-alpha order.
1. Press and hold in the Info/Menu button and the display will
show “Station order.”
2. Press and release the Select button.
3. Press the Tuning Up orDown buttons to choose between
favourite station, alphanumeric, active station and prune stations.
4. Press and release the Select button to select the station order
setting required.
Favourite stations
When this setting is switched on, after a period of time the most
listened to stations will move to the top of the station list and will be
marked with the heart symbol .
Alphanumeric
Press the Tuning Up orDown buttons until “Alphanumeric” appears
on the display. Your radio will now select stations in alphanumeric order
(0....9....A....Z).
All manuals and user guides at all-guides.com

13
Active station
When this setting is switched on the display will show only those that a
signal can be found for.
Prune stations
Some DAB services may stop broadcasting or you may not be able to
receive a station. Prune stations will delete the DAB stations from your
station list that can no longer be received.
When this feature is selected your radio will delete the stations that are
not currently being received.
All manuals and user guides at all-guides.com

14
GB
Operating your radio - FM
1. Carefully extend the telescopic aerial.
2. Press the On/Off button to switch on your radio. The display will
show “Welcome toDigital Radio” for a few seconds.
3. Press the Band button to select the FM band.
4. Press and release the Select button until the display shows
“Auto tune <>”.
5. Press the Tuning Up button to cause your radio to scan in an
upwards direction (low frequency to high frequency) and stop
automatically when it finds a station of sufficient strength.
6. After a few seconds the display will update and show station name
(if RDS information is available).
7. Press the Tuning Down button to scan the FM band in a downwards
direction (high frequency to low frequency).
8. When the waveband end is reached your radio will recommence
tuning from the opposite waveband end.
9.Adjust the Volume control to the required setting.
10. To switch off your radio press the On/Off button.
All manuals and user guides at all-guides.com

15
Manual tuning - FM
1. Press the On/Off button to switch on your radio.
2. Press the Band button to select the FM band. Fully extend the
Telescopic aerial.
3. Press and release the Select button until the display shows
“Manual tune <>”.
4. Press either of the Tuning Up or Down buttons to tune to a station.
The frequency will change in steps of 50kHz.
5. When the waveband end is reached the radio will recommence tuning
from the opposite waveband end.
6. Set the Volume control to the required setting.
7. To switch off your radio press the On/Off button.
All manuals and user guides at all-guides.com
all-guides.com

16
GB
Display modes - FM
In FM mode the bottom line of the display can be set to any of the
followingmodes:-
1. Press the Info/Menu button to cycle through the various modes.
Note:
When tuned to the FM band, information display is only available
when the radio is able to receive RDS information from the broadcaster.
Displays scrolling text messages
such as artist/track name, phone in
number etc.
Displays type of station being listened to
e.g. Pop, Classic, News, etc.
Displays current time and date.
Displays frequency of the station being
listened to.
a. Scrolling text
b. Program Type
c. Time and date
d. Frequency
All manuals and user guides at all-guides.com

17
Presetting stations
There are 5 memory presets for each of the two wavebands which allow
you to quickly tune the radio to your favourite stations. Presets are
store in a memory which remembers the settings even when the radio
is switched off.
1. Press the On/Off button to switch on your radio.
2. Tune to the required station as previously described.
3. Press and hold the required Preset button until the display shows
e.g. Preset 1 saved. The station will be stored under the chosen
preset button. Repeat this procedure for the remaining presets.
4. Stations stored in the memories may be overwritten by following the
above procedure.
Recalling a preset
1. Press the On/Off button to switch on your radio.
2. Select the required waveband.
3. Momentarily press the required Preset button, your radio will tune to
the station stored in preset memory.
All manuals and user guides at all-guides.com

18
GB
Stereo / Mono setting - FM
Your radio will play stereo broadcasts in stereo (via headphones) so
long as the received signal is of adequate strength. However, as a
stereo signal becomes weaker the audio signal will become poorer.
It may be preferable to force the radio to play the station in mono in
order to reduce the level of audio noise.
1. Press the On/Off button to switch on your radio.
2. Tune to the required FM radio station as previously described.
3. Press and hold the Info/Menu button until the display shows
“Mono Override” on the lower line. The upper line will show
“Override Off” if the radio is in the Auto-Stereo mode.
4. Press the Select button to switch on the Mono Override. While this
setting is engaged, the radio will play the current station in mono
whether listening via headphones or the loudspeaker.
Mono Override is a temporary setting and is applied to the currently
tuned station only. It is cancelled automatically by tuning to another
radio station.
5. If you wish to cancel Mono Override while listening to the currently
tuned radio station, press and hold the Info button until the display
shows “Mono Override” on the lower line. The upper line will show
“Override On” if the radio is in the Mono Override mode.
6. Press the Select button to switch off the Mono Override. The radio
will play then play the current station in stereo through headphones
if the signal is sufficiently strong.
All manuals and user guides at all-guides.com

19
Scan sensitivity setting - FM
Your radio will normally scan for FM broadcasts which are strong
enough to give good reception. However, you may wish the
Auto-scan function to also be able to find weaker signals, possibly from
more distant radio transmitters. Your radio includes a local / distant
option for theAuto-scan function.
1. Press the On/Off button to switch on your radio.
2. If needed, press the Band button to select the FM band.
3. Press and hold the Info/Menu button until the display shows
“Mono override” on the lower line.
4. Press and release the Tuning Up or Down buttons until the display
shows “FM Scan Zone” then press the Select button to enter the
scan zone selection menu.
5. Press the Tuning Up or Down buttons to switch between Local and
Distant options on the lower line of the display. TheDistant option will
allow the radio to find weaker signals when scanning.
6. Press the Select button to confirm your selection. The radio will then
revert to the normal information display. The Local orDistant setting
is stored in the radio and remains in force until changed or until a
System Reset.
Note:
The initial setting (out of the box, or after a System Reset) causes
the radio to ignore weak (distant) signals.
All manuals and user guides at all-guides.com