Sanremo SR405 User manual

16
FOREWORD
This instruction manual contains information and advice on the upkeep and how to get the best out of
your coffee machine.
Before using the appliance all the indications in this manual must be read and rigorously observed to
ensure the optimum performance and duration of your coffee machine, considering the user instructions
as an integral part of the appliance and therefore keeping them for its whole duration.
TECHNICAL DETAILS
WARNINGS
- The appliance must not be cleaned using solvents, thinners, spirits, etc. The use of warm water and
neutral detergent with a soft cloth are ideal to maintain the external and internal parts in good condi-
tion.
- The appliance must not be cleaned using a water jet.
- Do not put the appliance in water
- Since the appliance produces heat it should be kept in a cool location with the best ventilation possible,
for instance do not position it next to a radiator.
- The appliance is unsuitable for outdoor installation
- To ensure safe use the appliance not must be placed on a slope greater than 3°
- If the power cable is damaged, have it replaced by an After-Sales Service Centre, since a special tool
is required for this purpose.
- Before any maintenance ALWAYS unplug the mains power cable.
- Only connect to an adequately earthed electrical plant.
- Keep the appliance away from children
The manufacturer and the distributor shall not be under any liability for malfunctions in
the appliance, injury to persons and animals or damage to property arising from failure to comply with
part or all of the warnings or instructions given in this manual and from improper, incomplete or negli-
gence in maintenance and/or cleaning.
All technical assistance and maintenance can only be carried out by specialists authorised by the sup-
plier of the coffee machine.
ENGLISH
Width mm 230
Depth mm 347
Height mm 407
Reservoir capacity l 3.4
Net weight SR405 kg 13.7
Net weight SR405 Steam kg 14.6
Voltage V 220-240~
Coffee exchanger heating element input W 800
Steam exchanger heating element input W 1000
Electric pump input W 48
Steam micro-pump input W 16
Solenoid valve input in SR405 W 27
Solenoid valve input in SR405 V W 36

17
INSTALLATION
1. Unpack the machine and place it a secure, stable worktop, making sure there is sufficient space to
use it.
2. The appliance should be placed high enough to prevent easy access by children
3. Do not position it in proximity to tight passageways or corridors to avoid it being knocked.
4. Check the appliance is complete and has not been damaged (if in doubt call an After-Sales Service
Centre).
5. Take out the water tank (O) from its compartment (N), clean it, fill it with drinking water (preferably as
soft as possible), replace it in the compartment (N) returning the tubes in the tank.
6. Check that the data on the rating plate correspond to your mains electricity supply (e.g. 230 Volts,
etc)
7. Plug the power cable (Q) into the mains socket.
8. Switch the rear power switch (P) of the appliance to “I”
9. Wait for the green light (C) to go out before dispensing for the first time, to ensure that the correct
temperature has been reached.
USER INSTRUCTIONS
A- Orange LED - Power indicator - lights up to indicate the power supply is on
B- Red LED – No water – lights up to indicate the water tank is empty
C- Green LED – Temperature – lights up to indicate that the working temperature has been reached
D - Hot water button
E- Coffee button
F- Pod compartment flap
G- Hot water tube
H- Coffee tube
I- Drainer
L- Drip tray
M- Water tank lid
N- Water tank compartment
O- Water tank
P- Power switch
Q- Power cable
R- Steam button.
S - Steam nozzle
ENGLISH

18
COFFEE
- Place the cup under the coffee dispensing spout (H).
- Open the flap (F) located on top of the machine and fit a pod into the relative guide (fig.1).
- Close the flap (F) gently pushing it shut.
When the flap (F) is closed it pushes down the new pod, which in turn expels the previous one making it
fall into the drip / pod tray (L) (fig.2).
- To dispense: press the coffee button (E) to start and when the desired quantity has been reached press
it again to stop.
N.B.
- The pod is placed correctly inside the machine solely by the fin fitted on the flap (F),
NEVER use fingers to position the pod.
- NEVER open the flap (F) while the beverage is being dispensed.
- The machine is ready to dispense coffee or hot water after the green light (C) has gone out.
N.B.
In the morning, any barley/tea pods that have remained in the machine for the night could require slightly
more force to expel them, but should not cause other particular problems. To avoid this inconvenience,
however, it is of basic importance to ensure that there are no pods inside the machine at the end of
the day by expelling the last one using the provided empty pod (fig.3). The empty pod should obviously
not be thrown away, but recovered and reused after being properly cleaned.
fig.1 fig.2 fig.3
HOT WATER
- Place a cup under the hot water tube (G)
- Press the hot water button (D) and wait for the desired quantity to be reached
- Press the hot water button (D) again to stop.
STEAM
- Place the cup under the steam nozzle (S)
- Press the steam button (R) until the required quantity has been reached
- Press the steam button (R) to stop
ROUTINE CHECKS
- Rinse out the water reservoir at least once a week.
- Drip / pod tray (L): empty and clean the tray frequently.
- Check the level of pods inside the drip / pod tray (L) through the slit in the front of the tray.
N.B.
- Too many pods in the drip / pod tray (L) could impair / damage internal parts!! Empty out
the tray every 15-20 pods.
CLEANING
When cleaning the appliance, disconnect it from the electricity supply.
The housing and the steel parts should be cleaned with sponges and soft cloths to avoid scratching. Only
use detergents that do not contain abrasive powders or solvents and do not use steel wool.
ENGLISH

19
Drip / pod tray
ONCE EVERY 20 drinks empty out the drip/pod tray (L).
Periodically / at least once a week clean the drip/pod tray (L).
Empty pod
Cleaning cycles may also be carried out using the empty pod (fig.3). These cycles are recommended
at least once a week, before leaving the machine unused for any length of time, or immediately after
intensive use of BARLEY or TEA pods whose contents (very sugary) tend to form deposits that may be
reduced with timely cleaning.
To carry out the cleaning cycle just press the coffee button (E) when the empty pod has been put inside
the machine; leave the machine to operate for approx. 1 minute.
The empty pod will be expelled the next time a new pod is pushed in with the fin on the flap (F).
TROUBLESHOOTING
Appliance malfunction
Check that this is not due to:
- a power failure or blackout;
- an unplugged power cable;
- on/off switch on the rear of the appliance in position “0”.
No coffee
- check that the drip / pod tray is not too full. If it is, empty it.
- check that the red light(B) is not on. If it is, fill up the tank.
The flap (F) does not fully close
- check that the drip / pod tray is not too full. If it is, empty it.
The drip / pod tray cannot be removed
- the tray is too full of pods.
- pull out the tray by one centimetre and using a screwdriver release the grid (I) as shown in the figure.
For any other causes, contact the coffee machine manufacturer or an After-Sales Service Centre
WARRANTY
Any appliance that is purchased (keep the receipt, invoice, delivery note as proof) is covered by the statu-
tory warranty: this covers the replacement free of charge of parts with manufacturing defects as ascer-
tained by the After-Sales Service Centre or the manufacturer and so long as the appliance has not been
improperly used or tampered with by unauthorised persons or nevertheless using incorrect components
or techniques. Any defective parts shall be returned to the manufacturer.
ENGLISH

20
1 = Piston
2 = Coffee outlet
3 = Water outlet
4 = Reservoir
5 = Pump
6 = 3-way solenoid valve
7 = Single-acting valve
8 = Exchanger
9 = 2-way solenoid valve
WATER CIRCUIT DIAGRAM SR405
WIRING DIAGRAM SR405
1 = On/off switch
2 = Power on light
3 = No water light
4 = 3-way solenoid valve
5 = 3-way solenoid valve
6 = Pump
7 = 2-way solenoid valve
8 = Heating element
9 = Temperature indicator light
10 = 95° automatic thermostat
11 = 125° manual reset
thermostat
12 = Water switch
13 = Coffee switch
14 = No water microswitch
ENGLISH

21
1 = Piston
2 = Coffee outlet
3 = Water outlet
4 = Reservoir
5 = Pump
6 = 3-way solenoid valve
7 = Single-acting valve
8 = Exchanger
9 = 2-way solenoid valve
10 = Steam micro pump
11 = Drip tray
12 = Steam exchanger
13 = Steam outlet
WATER CIRCUIT DIAGRAM SR405V
WIRING DIAGRAM SR405V
1 = On/off switch
2 = Power on light
3 = No water light
4 = 3-way solenoid valve
5 = 3-way solenoid valve
6 = Pump
7 = 2-way solenoid valve
8 = Coffee exchanger heating element
9 = Temperature indicator light
10 = 95° automatic thermostat
11 = 125° manual reset thermostat
12 = Water switch
13 = Coffee switch
14 = No water microswitch
15 = Pump microswitch
16 = 3-way solenoid valve
17 = Steam exchanger heating element
18 = Steam switch
19 = 220° manual reset thermostat
20 = 165° automatic thermostat
ENGLISH

22
SR405 EXPLODED
ENGLISH

23
SR405 EXPLODED
ENGLISH

24
ENGLISH
POS. CODE DESCRIPTION
1 10038070A CAPSULE FRONT
2 10556014 FLAT ORANGE LENS
3 10556010 FLAT RED LENS
4 10556012 FLAT GREEN LENS
5 10805071 TCEI M4x10 A2 SCREWS
6 10853020 EMPTY PLASTIC CAPSULE
7 10951000 MAN. SANREMO ADHESIVE LABEL
8 10038050 CAPSULE DISCHARGE TANK
9 10038060 GRILL WITH PARTITION
10 10952618 EMPTY CAPSULE LABEL
11 10352058 FEET
12 10905010 SILICONE TUBE 7x4
13 10024318 GREY CASING SR405
14 10402046 MICRO SPRING
15 10809000 M12x0.75 NUT FOR MICRO
16 10112056 WATER EMPTY MICRO
17 10038010 TANK-PUMP SUPPORT
18 10203068 TC+ SW M4x10 ZN SW SCREWS
19 10111054 MAIN SWITCH
20 10105010 CABLE LEAD
21 10803519 WASHER D4.2 TOOTHED ZN
23 10105130 BLACK 3X1 POWER SUPPLY CABLE
24 10024298 BLACK BACK SR405 - 505
25 10955024 GROUND CONNECTION ADHESIVE LABEL
26 10355178A TANK IMPURITIES FILTER
27 10355105 TANK STOPPER D.45
28 10353500 TANK HANDLE WITH TONGUES
29 10353243B 3.4 LT TANK WITH RIBBING
30 10955026 CUT VOLTAGE LABEL
31 10112202 D.10 TH.1.5 MAGNET
32 10024224 TANK LID
33 10805510 3MA NUT ZN FINE
34 10024322 GREY CASING ROD SR405 - 505
35 10038030 CAPSULE DOOR HINGE
36 10955012 HOT SURFACE LABEL
37 10038024A GREY CAPSULE DOOR
38 10024288 GREY FIN PLATE
39 10553080 CM SWITCH
40 10553084 SWITCH SUPPORT
41 10553082 CONVEX KEY
42 10556016 230V NEON SIGNALLER
43 10556018 230V FLUORESCENT SIGNALLER
44 10024290 CAPSULE GUIDE WITHOUT TONGUES
45 10805135A TC+ 3x10 ZN TT SCREWS
46 10024206 FRONT REINFORCEMENT
47 10806665 FLAT D3 WASHER ZN
49 10853210 RAPID L CONNECTION 4x1/8”M
50 10102205 THERMOSTAT CABLE
51 10111033 95° AUTOMATIC THERMOSTAT
52 10115030 125° THERMOSTAT, MANUAL RESET
53 10040043B SEPARATE EXCHANGER
54 10024220 LOWER CAPSULE GUIDE
55 10852022 2611 1/8”M STOPPER
56 10853204 STRAIGHT RAPID CONNECTION 4x1/8M
57 10023252 SPOUT-COVER TUBE
58 10303010A 2-WAY 230V SOLENOID VALVE
59 10852210 L CONNECTION 1/8” M/F
60 10102510 SR405 230V CABLING HARNESS
61 10652023A UNIDIRECTIONAL VALVE
62 10853223 T CONNECTION 1/8” M/M/F
63 10809019 ZNN TBEI M3x8 SCREWS
SR405 EXPLODED VIEW CAPTIONS, UPDATE 05-06
POS. CODE DESCRIPTION
64 10303021 3-WAY 230V SOLENOID VALVE
65 10255030 L-SHAPED PIPETTE
66 10011524 L-SHAPED PUMP SUPPORT
67 10255016 EP4 230V PUMP
68 10255040 THERMO-PROTECTOR
69 10809002 FLAT D6.4X24X2 ZN WASHER
70 10805114 TC+ SW M5x12 ZN SW SCREWS
71 10023290 DIE-CAST UPPER DISK
72 10503018 PISTON UNIT GASKET
73 10503011 LIP GASKET DEM50
74 10023321 PISTON DISK M12
75 10023336 CAPSULE PISTON SHANK
76 10652064A CONICAL SPRING D.2.5
77 10023304 PISTON UNIT CYLINDER
78 10809012 FLANGED 6MA ZN NUT
79 10023292 INT.78 PISTON FLANGE
80 10023329A HEX.10 UNIT UPRIGHT
81 10040058 GLASS
82 10105014 CABLE LEAD
83 10909010 D.4x2.5 TEFLON TUBE
84 10955025A GROUNDING SYMBOL LABEL
85 10052296 PISTON UNIT SR405
86 10853222 Y-SHAPED CONNECTION
87 10024302 BLACK FRAME SR405
88 10801036 TSPEI M5x18 ZN UNI 5933 SCREWS
89 10040005 HEAT EXCHANGE SPACER
90 10402062 OR 115 VITON
91 10040033 HEAT EXCHANGE SPIRAL
92 10115019 D12.5 800W 230V RESISTANCE
93 10853203 RAPID T-SHAPED CONNECTION 4-4-1/8M
94 10505035 BLACK GASKET
95 10502016 WATER MICRO PTFE WASHER
96 10502028 OR 3037 VITON

25
SR405V EXPLODED
ENGLISH

26
SR405V EXPLODED
ENGLISH

27
ENGLISH
POS. CODE DESCRIPTION
1 10038070A CAPSULE FRONT
2 10556014 FLAT ORANGE LENS
3 10556010 FLAT RED LENS
4 10556012 FLAT GREEN LENS
5 10805071 TCEI M4x10 A2 SCREWS
6 10853020 EMPTY PLASTIC CAPSULE
7 10951002 MAN. VAP. SANREMO LABEL
8 10038054 WAFFLE DISCHARGE TANK
9 10038060 GRILL WITH PARTITION
10 10952618 EMPTY CAPSULE LABEL
11 10352058 FEET
12 10905010 SILICONE TUBE 7x4
13 10024318 GREY CASING SR405
14 10402046 MICRO SPRING
15 10809000 M12x0.75 NUT FOR MICRO
16 10112056 WATER EMPTY MICRO
17 10038010 TANK-PUMP SUPPORT
18 10203068 TC+ SW M4x10 ZN SW SCREWS
19 10111054 MAIN SWITCH
20 10105010 CABLE LEAD
22 10105130 BLACK 3X1 POWER SUPPLY CABLE
23 10805027A TBL+ M4x10 A2 SCREWS
24 10024298 BLACK BACK SR405 - 505
25 10955024 GROUND CONNECTION ADHESIVE LABEL
26 10355178A TANK IMPURITIES FILTER
27 10355105 TANK STOPPER D.45
28 10353500 TANK HANDLE WITH TONGUES
29 10353243B 3.4 LT TANK WITH RIBBING
30 10955026 CUT VOLTAGE LABEL
31 10112202 D.10 TH.1.5 MAGNET
32 10024224 TANK LID
33 10805510 3MA NUT ZN FINE
34 10024322 GREY CASING ROD SR405 - 505
35 10038030 CAPSULE DOOR HINGE
36 10955012 HOT SURFACE LABEL
37 10038024A GREY CAPSULE DOOR
38 10024288 GREY FIN PLATE
39 10553080 CM SWITCH
40 10553084 SWITCH SUPPORT
41 10553082 CONVEX KEY
42 10556016 230V NEON SIGNALLER
43 10556018 230V FLUORESCENT SIGNALLER
44 10024290 CAPSULE GUIDE WITHOUT TONGUES
45 10805135A TC+ 3x10 ZN TT SCREWS
46 10024206 FRONT REINFORCEMENT
47 10806665 FLAT D3 WASHER ZN
49 10853210 RAPID L CONNECTION 4x1/8”M
50 10102205 THERMOSTAT CABLE
51 10111033 95° AUTOMATIC THERMOSTAT
52 10115030 125° THERMOSTAT, MANUAL RESET
53 10040043B SEPARATE EXCHANGER
54 10024220 LOWER CAPSULE GUIDE
55 10852022 2611 1/8”M STOPPER
56 10853204 STRAIGHT RAPID CONNECTION 4x1/8M
57 10023252 SPOUT-COVER TUBE
58 10303010A 2-WAY 230V SOLENOID VALVE
59 10852210 L CONNECTION 1/8” M/F
60 10102512 SR405 230V CABLING HARNESS
61 10652023A UNIDIRECTIONAL VALVE
62 10853223 T CONNECTION 1/8” M/M/F
63 10809019 ZNN TBEI M3x8 SCREWS
64 10303021 3-WAY 230V SOLENOID VALVE
POS. CODE DESCRIPTION
65 10853070 L-SHAPED RUBBER CONNECTION
66 10011524 L-SHAPED PUMP SUPPORT
67 10255016 EP4 230V PUMP
68 10255040 THERMO-PROTECTOR
69 10809002 FLAT D6.4X24X2 ZN WASHER
70 10805114 TC+ SW M5x12 ZN SW SCREWS
71 10023290 DIE-CAST UPPER DISK
72 10503018 PISTON UNIT GASKET
73 10503011 LIP GASKET DEM50
74 10023321 PISTON DISK M12
75 10023336 CAPSULE PISTON SHANK
76 10652064A CONICAL SPRING D.2.5
77 10023304 PISTON UNIT CYLINDER
78 10809012 FLANGED 6MA ZN NUT
79 10023292 INT.78 PISTON FLANGE
80 10023329A HEX.10 UNIT UPRIGHT
81 10040058 GLASS
82 10105014 CABLE LEAD
83 10025557 MICRO PUMP SUPPLEMENTARY ROD
84 10955025A GROUNDING SYMBOL LABEL
85 10805166 TC+ SW M3x6 ZN SW SCREWS
86 10853222 Y-SHAPED CONNECTION
87 10024306 BLACK FRAME SR405 V
88 10801036 TSPEI M5x18 ZN SCREWS
89 10255003 MINI STEAM PUMP 230V
90 10255030 L-SHAPED PIPETTE
91 10040005 HEAT EXCHANGE SPACER
92 10505035 BLACK GASKET
93 10853203 4-4-1/8M RAPID T-SHAPED CONNECTION
94 10402062 OR 115 VITON
95 10040033 HEAT EXCHANGE SPIRAL
96 10115019 D12.5 800W 230V RESISTANCE
97 10024200 STEAM EXCHANGE PROTECTION
98 10040050 1000W 230V STEAM EXCHANGE
99 10040052 STEAM EXCHANGE SPIRAL
100 10115026 AUTOMATIC 165° THERMOSTAT
101 10115024 220° THERMOSTAT WITH MAN. RESET
102 10803519 D4.2 TOOTHED ZN WASHER
103 10853083 CONNECTION NUT 1/2 HEX.26x6
104 10852058 RING NUT FOR STEAM FRONT
105 10852057 STEAM NOZZLE JOINT
106 10656010 SPRING FOR HEAD / JOINT
107 10853051 JOINT PRESS PLATE
108 10502037 OR 120 VITON
109 10402024 TAP JOINT BLACK NUT
110 10402063 OR 115 EPDM
111 10402296 STEAM NOZZLE WITH SPHERE
112 10402302 COMPLETE CAPPUCCINO MAKER
113 10753054 ANTI-BURN JOINT
114 10909010 TEFLON TUBE D.4x2.5
115 10052314 STEAM EXCHANGER UNIT 230V
116 10040008 SPACER D20xD5.5xH4
117 10805083 TE M4x12 ZN SCREWS
118 10052296 PISTON UNIT SR405
119 10353220 BRAIDING CONNECTION L 1/8”M
120 10909015 TEFLON TUBE D.5x3
121 10502016 WATER MICRO WASHER PTFE D20x1.5
122 10502028 OR 3037 VITON
SR405 V EXPLODED VIEW CAPTIONS, UPDATE 05-06