Sanyo LNS-T03 Use and care manual

Type of the Cabinet (1) (See Page 2)
LCD PROJECTOR LENS
MODEL NO. LNS-T03
LENS REPLACEMENT
AND INSTALLATION PROCEDURES
NOTES ON REPLACEMENT AND INSTALLATION
The procedures and the needed pars for lens installation depend on the type of
cabinet. Before installing or replacing the lens, make sure the type of cabinet of your
projector.
When installing or replacing the lens, make sure the Lens Model No. matches with to
your projector. Refer to the catalog, or contact your sales dealer for the proper Lens
Model No.
TYPE OF THE CABINET AND INSTALLATION PROCEDURES
Check the type of cabinet of your projector and follow the respective installation procedure
to install the lens correctly.
Type of the Cabinet (2) (See Page 5)
1AA6P1P4097-- (IDLS)
For lens installation to the other models than above, contact your sales dealer.

Not all the parts included may be used for lens installation or replacement. Keep these
parts for later use.
Note : Illustrations in this manual may differ from the actual product.
NOTES ON LENS INSTALLATION
• Lens installation and replacement should be made by the qualified service per-
sonnel.
• Be sure to install the lens following this procedure precisely.
• The lens cover is attached to the lens for protection. Be sure to remove the lens
cover from the lens before installation.
• When installing or replacing the lens, be careful not to stain, scratch or damage
its surface.
After installing or replacing the lens, be sure to confirm the followings for safety.
1. Make sure the lens is fixed on the projector.
2. Make sure no part is missing, or loose.
BE SURE TO CHECK THE FOLLOWING MATTERS FOR SAFETY
LIST OF CONTENTS
Following parts are included in the package.
• LENS 1 pc
• DRIVER 1 pc
-1-

LENS REPLACEMENT AND INSTALLATION PROCEDURE {Type (1) Cabinet}
-2-
1Remove 2 Screws A and Remove Lower Lens
Cover. Push part B and pull the Lower Lens
Cover down and remove it. (See Fig. 1.)
2Remove 4 Screws C. Pull the Upper Lens Cover toward front and remove it. (See Fig. 2.)
3Remove 2 Screws D and Cover Plate from the back of the Upper Lens Cover. (See Fig. 3.)
A
C
C
B
Fig-3
Fig-1
Fig-2
UPPER LENS
COVER
COVER PLATE
UPPER LENS
COVER
LOWER LENS
COVER
D

-3-
LENS LOCK RELEASE
Fig-4
LENS LOCK
4Remove Lens Protection Cap from the rear (mounting side) of the Projection Lens and attach the
lens Attachment to the lens with 4 Screws. (Use screws attached to the lens.) See Fig. 4.
5Grasp (release lock) the Lens Lock Lever and turn it fully upward. (See Fig. 6)
Mount the Lens into the lens mounting bracket and grasp the lens lock lever and turn it counter-
clockwise until the lever is locked. (See Fig. 5 and 7)
After installing the lens, make sure the lens is not loose and properly installed.
Grasp (unlock)
Lens Lock Lever
and pulling
upward.
Grasp (unlock) Lens
Lock Lever and fully
pulled downward until it
is locked (clicked).
Fig-6 Fig-7
LENS ATTACHMENT
Lens Attachment 01
POA-LNA-01
(610 303 8742)
Part No. (610 275 6029)
DRIVER INCLUDED
IN THE LENS PACKAGE
LENS LOCK
LEVER
Fig-5
LENS INSTALLATION NEEDS TWO OR MORE PEOPLE.
TO INSTALL THE LENS BY A SINGLE PERSON MAY RESULT IN A SERIOUS DAMAGE
ON THE LENS OR THE PROJECTOR BY DROPPING OR BUMPING THE PRODUCTS.
6Set up the projector and project image on the screen. Turn the lens part "A" to adjust ZOOM. Turn
the lens part "B" to adjust FOCUS.
Turn the lens part "A"
to adjust ZOOM.
Turn the lens part "B"
to adjust FOCUS.
A
B
LENS MOUNTING
BRACKET

-4-
7Put back the Upper Lens Cover to the projector and Fix the Upper Lens Cover with 4 Screws C.
(See Fig. 2.) Put back the Lower Lens Cover to the projector. Fix the Lower Cover with 2 Screws A.
(See Fig. 1.)
Fig-8
LOWER LENS
COVER
UPPER LENS
COVER

LENS REPLACEMENT AND INSTALLATION PROCEDURE {Type (2) Cabinet}
-5-
2Remove 4 Screws C. Pull the Lower Lens Cover toward front and remove it. (See Fig. 2.)
3Remove 2 Screws D and Cover Plate from the back of the Upper Lens Cover. (See Fig. 3.)
Fig-1
UPPER LENS
COVER
Fig-2
LOWER LENS
COVER
C
COVER PLATE
UPPER LENS
COVER
D
Fig-3
C
B
A
1Remove 2 Screws A and Remove Upper Lens
Cover. Push part B and pull the Upper Lens
Cover up and remove it. (See Fig. 1.)

-6-
LENS LOCK RELEASE
Part No. (610 275 6029) Fig-4
LENS LOCK
4Remove Lens Protection Cap from the rear (mounting side) of the Projection Lens and attach the
lens Attachment to the lens with 4 Screws. (Use screws attached to the lens.) See Fig. 4.
5Grasp (release lock) the Lens Lock Lever and turn it fully upward. (See Fig. 6)
Mount the Lens into the lens mounting bracket and grasp the lens lock lever and turn it counter-
clockwise until the lever is locked. (See Fig. 5 and 7)
After installing the lens, make sure the lens is not loose and properly installed.
Lens Attachment 01
POA-LNA-01
(610 303 8742)
LENS ATTACHMENT
LENS LOCK
LEVER
Fig-5
Fig-6 Fig-7
Grasp (unlock) Lens
Lock Lever and fully
pulled downward until
it is locked (clicked).
Grasp (unlock)
Lens Lock Lever
and pulling
upward.
LENS INSTALLATION NEEDS TWO OR MORE PEOPLE.
TO INSTALL THE LENS BY A SINGLE PERSON MAY RESULT IN A SERIOUS DAMAGE
ON THE LENS OR THE PROJECTOR BY DROPPING OR BUMPING THE PRODUCTS.
A
B
6Set up the projector and project image on the screen. Turn the lens part "A" to adjust ZOOM. Turn
the lens part "B" to adjust FOCUS.
Turn the lens part "A"
to adjust ZOOM.
Turn the lens part "B"
to adjust FOCUS.
DRIVER INCLUDED
IN THE LENS PACKAGE
LENS MOUNTING
BRACKET

-7-
Fig-8
LOWER LENS
COVER
UPPER LENS
COVER
7Put back the Lower Lens Cover to the projector and Fix the Lower Lens Cover with 4 Screws C.
(See Fig. 2.) Put back the Upper Lens Cover to the projector. Fix the Upper Cover with 2 Screws A.
(See Fig. 1.)