Sanyo VCC-6975P User manual

Colour
PAL
VCC-6975P
TV LinesHorizontal
*Specifications subject to change without notice
please consult the instruction manual to ensure safe and proper operation of the product.*Caution:
SF-1407MV
1/3" Colour CCD
High-resolution Camera
High-resolution Camera
Intelligent digital motion detector
SSP compatible
x32 Electronic sensitivity (minimum illumination of 0.05 Lux)
(minimum illumination of 0.05 Lux)
x8 Digital zoom with digital pan and tilt
Built in DSP (digital signal processing) circuit
480 TV lines of horizontal resolution
Dual power operation, 24V AC / 12 V DC
1/3" Colour CCD
High-resolution Camera
Intelligent digital motion detector
SSP compatible
x32 Electronic sensitivity (minimum illumination of 0.05 Lux)
x8 Digital zoom with digital pan and tilt
Built in DSP (digital signal processing) circuit
480 TV lines of horizontal resolution
Dual power operation, 24V AC / 12 V DC
Accredited
by the RvA
ISO 9001 REGISTERED FIRM
DNA Certification B. V., THE NETHERLANDS

3
2
1
7
6
5
4
Direction
It is possible to narrow the target to objects moving in certain
directions only. This feature enables the system to detect people
coming into a room while disregarding people going out. It is also
possible to detect all moving objects without setting the direction.
Size
Freely set the size of target objects.
Masking
Freely establish the area where motion detection is turned off.
Magnitude of movement
Set the magnitude of movement to be detected.
Brightness
Set the lowest level of brightness to be analyzed. Use this feature
to avoid influences of electric noises on the darker area of the
screen.
Magnitude of brightness shift
Set the magnitude of changes in brightness. This feature is used
to disregard a sudden and huge change in brightness such as one
caused by turning on/off the lights.
Duration
Set the time the system should continue monitoring before identi-
fying a moving object. This feature enables the system to neglect
high speed objects such as automobiles.
1
15 1010
5
An all-new Intelligent Digital Motion Detector is built-in to detect moving objects in the picture and send an alarm
The intelligent Digital Motion Detector analyzes changes in picture brightness on the screen and uses the direction of motion and size
of the object to identify moving objects. The system can be set to produce an external alarm signal and/or switch to a x2 digital zoom-
in display. Furthermore, the center of the zoom-in picture stays focussed on the moving object.
Reliable detection of moving objects
The intelligent Digital Motion Detector uses seven factors in analyzing changes in picture brightness to enable reliable motion detec-
tion and reduce false alarms.
An area where motion
detection is turned off
Set the direction to “right”
CAMERA 1DIRECTION
1/3" Colour CCD
High-resolution Camera
VCC-6975P
Time
Noise
Not detection
Brightness
Shown with optional lens
*The intelligent Digital Motion Detector function is not available when the electronic
sensitivity is set to ON or when the electronic shutter is set to “long mode”.
x2 zoom x2 zoom
Intelligent digital motion detector uses size of
object and direction of motion to identify mov-
ing objects.
Display of monitor
Detection of a moving object prompts the
camera to zoom in on the object (x2), and
blinking camera ID is displayed on the moni-
tor. An external alarm signal is also sent.
Display of monitor
During the zoom-in display, the center of the pic-
ture travels and stays focussed on the object.
Duration of the zoom-in display is adjustable to
5, 10, 20, 30, and 60 seconds.
Display of monitor
CAMERA 1 CAMERA 1

x32 electronic sensitivity
When the illuminance of the monitoring point drops down,
electronic sensitivity can be automatically increased to x32
(max.) to brighten up the image. The minimum illuminance on
the object is 0.05 Lux (using F1.2 lens) which makes it possi-
ble to obtain a clear picture with almost no light at all.
The automatic increase in gain can be set to x2, x4, x8, x16,
or x32.
The camera can even cope with a gradual and continuous
change in illuminance from day to night and maintains a crisp
picture by successive adjustments of the auto iris, auto gain
control, and electronic shutter.
High quality image with DSP
The adoption of a new DSP (Digital Signal Processor) has
brought up the quality standard of the monitored image for reli-
able surveillance.
1) By digitizing the Colour processing, Colour reproduction has
been largely enhanced.
2) DSP maintains crisp borders and also restricts smear and
smudges of Colour. It further enables a wide choice of set-
tings to control the degree of edge compensation.
On-screen settings
Camera settings can be easily controlled through on-screen
menus. A new setting will be reflected on the monitor to make
optimum settings easy.
Menu languages built in: English / French / Germany
x8 digital zoom with digital pan and tilt
Digital zoom of x2, x4, and x8, or continuous zooming up to x8
is available. The center of zooming can also be moved around
in all directions. Zooming can be controlled via SSP or by
means of a remote control circuit.
Two types of backlight compensation with fine tuning
1) Multi-spot photometry mode setting
This mode enables the user to specify screen areas, among 32
blocks, in which illuminance measurements will not take place.
The picture display will be kept to optimum brightness accord-
ing to the illuminance measurements obtained in other areas.
2) 5-section photometry mode setting
The screen will be divided into 5 sections to which the user
will assign 15-scale weights.
The brightness of the picture will be kept at optimum by giving
priority to the area with the higher weight. (A DC type auto-iris
lens is required to enable this mode.)
Three types of white-balance adjustment
1) Automatic tracking mode to adjust white-balance as the light
(Colour temperature) at the monitoring point changes.
2) Push-and-lock mode to adjust white-balance when the set
button is pushed.
3) Manual white-balance by adjusting R and B volume.
Camera ID display
An 8-character (max.) camera ID can be super-imposed on the
monitor. The user can change the display to any position on
the screen.
Three types of synchronization
Internal, line lock, or external sync. can be selected. Selection
= between internal and line lock sync. mode is done
on-screen. The camera automatically switches to external
sync. mode by receiving a VBS. (Line lock sync. mode is avail-
able only with 24 V AC power supply.)
Dual power operation
24 V AC or 12 V DC applicable.
13 mode electronic shutter
Short mode: 1/50, 1/120, 1/250, 1/500, 1/1000, 1/2000,
1/4000, and 1/10000 sec.
Long mode: 2/50, 4/50, 8/50, 16/50, and 32/50 sec.
1/3" CCD image sensor with approx. 470,000 picture elements
480 TV lines of horizontal resolution
Electronic iris (indoor use)
SSP (RS-485) compatibility
The whole security system, including the VCC-6975P, may be
controlled by a VSP-7000 system controller using a new com-
munication protocol SSP (Security Serial Protocol).
Remote control functionality on VSP-7000 includes all
on-screen menu items of the VCC-6975P.
System Controller VSP-7000 (sold separately)
When the electronic sensitivity is set to ON
Areas in which illuminance will
not be measured
SSP: Bi-directional communications (half duplex)
Maximum cable length for communication up to 1200 m (4000 feet)
An example of weight setting:
Top = 1, Bottom = 5, Left = 10,
Right = 10, Center (fixed) = 15.
The size and position of the cen-
ter area is adjustable.
1
15 1010
5
1
15 1010
5
Features
Security Serial Protocol
SSP
Command
Alarm
Multiplexer VCR VSP-7000
Up to 256
devices
VCC-6975PVCC-6975PVCC-6975P VCC-6975P

Power supply terminals
24 V AC and 12 V DC dual power capability
eliminates limitations on camera location.
Y/C signal output terminal
Type of coaxial cable and maximum length
•Mini-DIN round type 4-pin, 10m maximum
VCC-6975P rear panel
V phase adjustment
Scanning system
Image sensor
Picture elements
Horizontal resolution
Minimum illumination
Motion detector
Backlight compensation
White balance
Electronic shutter
Light control
Lens mount
Flange back
Auto iris lens
Auto iris output
Lens iris level
Synchronizing system
Auto iris lens
Power requirement
Power consumption (approx.)
Camera mount
Dimensions (approx.)
Weight (approx.)
Gain control
Power supply
External sync.
Video signal
Sockets
PAL standard 625 lines, 25 frames/sec.
1/3" (approx. 4.8 mm x 3.6 mm) interline transfer method CCD
Total: 795(H) x 596(V), Effective: 752(H) x 582(V)
480 TV lines
Approx. 1.4 Lux (F1.2, normal mode)
Approx. 0.05 Lux (F1.2, x32 electronic sensitivity)
ON / OFF ––– (on screen)
ON = x2 / x4 / x8 / x16 / x32 ––– (on screen)
Electronic sensitivity ON / OFF ––– (on screen)
Alarm out: RS485 (G, B, A) and ALARM (C, A)
Multi-zone light measuring system
ON / OFF ––– (on screen)
Short mode: 1/50, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 sec. ––– (on screen)
Long mode: 2/50, 4/50, 8/50, 16/50, 32/50 sec. ––– (on screen)
Optical auto iris lens / Electronic iris (indoor use)
CS / C mount (C mount: using C-mount adaptor supplied)
12.5 mm ±0.5 mm adjustment
DC / VIDEO ––– Slide SW (side)
LEVEL: L~H ––– (on screen)
1.4 Lux to 70,000 Lux (F1.2), 2.0 Lux to 100,000 Lux (F1.4)
ON / OFF ––– (on screen)
External sync. automatic switching
Internal sync. / Line lock ––– (on screen)
LENS ––– 4-pin (side)
Temperature: -10°C to 50°C [14°F to 122°F], Humidity: within 90% RH
24 V AC, 50 Hz or 12 V DC
24 V AC: 4.0 W (with auto iris lens), 12 V DC: 4.1 W (with auto iris lens)
1/4"–20 UNC (top / bottom selectable)
ON (Automatic) / OFF ––– (on screen)
24 V AC, GND ––– 3-pin terminal (rear) 12 V DC ––– 2-pin terminal (rear)
VIDEO OUT ––– BNC (rear)
Y/C signal out mini-DIN 4-pin (rear)
SSP (RS-485) RS485 (G, B, A) ––– Pushbutton terminal x 1 pair (rear)
Alarm signal ALARM (C, A) ––– Pushbutton terminal x 1 pair (rear)
Electronic iris
Electronic iris range
Environmental conditions
VCC-6975PMODEL
LINE PHASE ––– (on screen)
(TTL) ATW / AWC / Manual ––– (on screen)
DC: Drive coil (+, -), Brake (Damp) coil (+, -)
VIDEO: +12 V DC (Max. 50 mA), Video output (high-impedance)
VBS IN ––– BNC (rear)
67(W) x 54(H) x 126.5(D) mm
[2.64(W) x 2.13(H) x 4.98(D) in.] (w/o camera & lens mounts)
470 g [16.6 oz.] (w/o lens)
ON = Multi-spot photometry / 5-section photometry ––– (on screen)
Video output level 1.0 V (p-p) (75 ohms, composite)
Video S/N ratio More than 48 dB
Electronic zoom ON / OFF ––– (on screen)
ON = Continuance (up to x8), Fix (x2 / x4 / x8), Pan / tilt operation
Gamma ON ( γ= 0.45) / OFF ––– (on screen)
Camera ID ON (up to 8 characters) / OFF ––– (on screen)
Mirror image effect H, V, H/V, 3 mode reverse image
Synchronization
signal input terminal
SSP terminal
LENS
SET
CURSOR
15.4
LENS 4-pin
67
54
28
25.2
11
1/4"–20 UNC threaded hole
(top / bottom selectable)
1 126.5 9.5
136
ADJ. LOCK
DIGITAL
COLOR CCD CAMERA
FLANGE BACK
VCC-6975P
(Unit: mm)
TLS-9960P
TLS-9168P
TLS-9024P
960-hour Recording Time Lapse VCR
VSP-7000
SSP System Controller
168-hour Recording Time Lapse VCR
MPX-CD162P
MPX-MD162P
16-channel Duplex Multiplexer (Colour)
16-channel Duplex Multiplexer (B/W)
MPX-CD92P
9-channel Duplex Multiplexer (Colour)
MPX-MS92P
9-channel Simplex Multiplexer (B/W)
24-hour Recording Time Lapse VCR
SSP corresponding devices As of March 2000
Multiplexer
System Controller
Time Lapse VCR
SRT-7168P
168-hour Recording + Realtime VCR
SRT-6000P
40-hour Recording + Realtime VCR
Realtime VCR
*More models will be introduced soon.
VCL-CS8LY
Standard Lens
VA-TS6ZE-LY
x 6 Manual Zoom Lens
VCL-CS4LY
Wide-angle Lens
VCL-CS2LYA
Super Wide-angle Lens
VA-TS420PE-LY
Pinhole Lens
VA-TS2VE-LY
Vari-focal Lens
VA-TS10ZME-LY
x 10 Motorized Zoom Lens
VA-TS6ZME-LY
x 6 Motorized Zoom Lens
Lenses for 1/3" CCD camera
VAC-60 (sold separately)
Camera Set-up Unit
AC adaptor
(for VCC-6975P)
VCA-35E (sold separately)
Video output terminal
Camera input terminal
Environmental conditions
Power requirement
BNC x 1
BNC x 1
Temperature: 0°C to 40°C [32°F to 104°F], Humidity: 10 to 90%
3 V DC, Alkali type AAA format batteries x 2
Dimensions
90(W) x 135(H) x 36(D) mm [3.54(W) x 5.32(H) x 1.42(D) in.]
Weight (approx.) 230 g [8.1 oz.]
VAC-60MODEL
Power requirement
Power consumption (approx.)
Dimensions (approx.)
Weight (approx.)
220 ~ 230V AC, 50 Hz
17 VA max.
68(W) x 62(H) x 100(D) mm [2.68(W) x 2.44(H) x 3.94(D) in.]
680 g [24 oz.]
VCA-35EMODEL
Monitor
Video output terminal
Type of coaxial cable and maximum length
•Cable type RG-59U (3C-2V), 250m maximum
•Cable type RG-6U (5C-2V), 500m maximum
•Cable type RG-11U (7C-2V), 600m maximum
LENS
SET
CURSOR
VCC-6975P
VAC-60
VAC-60 rear panel
SANYO Electric Co., Ltd.
Distributed by:
Video Imaging Systems Division
© 2000 SANYO Printed in Japan '00.3. AP
Remote set-up makes you feel you have the camera right
beside your monitor. Capable of setting up VCC-6975P
for all on-screen menu items (intelligent digital motion
detector, backlight compensation, white-balance, etc.)
For better picture quality, disconnect this unit after
settings are completed.
*Specifications subject to change without notice
*Specifications subject to change without notice
please consult the instruction manual to ensure safe and proper operation of th
please consult the instruction manual to ensure safe and proper operation of th
e product.
e product.
*Caution:
*Caution:
*Specifications subject to change without notice
please consult the instruction manual to ensure safe and proper operation of the product.*Caution:
1/3" Colour CCD
High-resolution Camera
Intelligent digital motion detector
SSP compatible
x32 Electronic sensitivity
(minimum illumination of 0.05 Lux)
x8 Digital zoom with digital pan and tilt
Built in DSP (digital signal processing) circuit
480 TV lines of horizontal resolution
Dual power operation, 24V AC / 12 V DC