Sanyo CZP3012 User manual

Instruction
Manual
.
Co[our
Television Model CZP3012 I
CZP6012
:CZP4-012
——
---
SPECIAL FUNCTIONS
CHANNEL SCANNING

,
.,’
\
3
,:.,.
,/.~.L =.
- +.-
. .,
.*.
‘J
.----
Controls
L-
\\\
N(\
CONTROL
SETTING
Button
Programme
Selector
Standby and -
Power Indicator
Mains ON/OFF
Switch
SOUND
g.Jflum
->> +1“H14JP=LE~ gB:;; ‘-+
CONT.
Jtc1
Headphone
Jack LMEMORY
T, V./Vi DEO
Selector
DISPLAY ;1
0
CONTROL
SELECTOR
:PRESET
IBAND
@3 EARCH
ON-SCREEN DISPLAY: EXAMPLE
●PROG. poslT[o N
Display time
continues for 5sec. r28 c1
Display time
continues for 5sec. L-L&l
●VIDEO MODE
Display time
continues for 5
●TIJNING
(Pre-Setting)
Display time
sec.
continues during
~PRESET switch ON,
–l–’
.
.,-
. .. . . .

General Operation
o,,.. Mains ON/OFF Sw-tch
The set is switched on by pressing button O. To switch off, press button
again.
NOTE To switch “ON” the Wset in the standby mode:
Press the Power ON/OFF button ~on the remote control trans-
mitter, the CONTROL SEITING Button @(on the Wset) or the
Programme Selector@ (on the TVset). The TVset can not be turned
on by pressing the Mains ON/OFF Switch O(on the TV set) in the
standby mode.
IMPORTANT Be sure to turn the TV OFF with the Mains ON/OFF
Switch O,if the power failure occurs while viewing.
@.... Programme Selection
Press the right side (+) of the prograrnme selector ~, and the TV set will step
up to the next station, i.e; 1, 2, 3..“. 29, VCR1, VCR2, VCR3,, 1, 2, 3. . .
Press the left side (–), and the TV set will step down to the previous station.
The position number is displayed on the screen.
0.... T. V./VlDEO Selector Button
To watch television programmed leave this switch in the T.V. mode. When this
switch is set to the VIDEO mode you can enjoy the playback from VCR or
other AV equipment connected to the AV input terminals. “AV” is displayed
on the screen,
CONTROL SETTING
❑Select the CONTROL FUNCTION (SOUND VOLUME, COLOUR, BRIGHT-
NESS or CONTRAST) by pressing the CONTROL SELECTOR ~button.
*Each time the CONTROL SELECTOR button ~is pressed, the CON-
TROL FUNCTION changes as follows;
ISOUND VOLUME -CO LOUR— BRIGHTNESS —CONTRAST
IkI
I*“SOUND”, “COLOUR”, “BRIGHT” or “CONTRAST” is displayed on
Ithe screen.
t
❑Adjust the SOUND VOLUME, COLOUR, BRIGHTNESS or CONTRAST to
the desired level by pressing the CONTROL SETTING @button.
@.... MEMoRY0
Present SOUND VOLUME, CO LOUR, BRIGHTNESS and CONTRAST levels
can be set into the memory by pressing the MEMORY ~button, and these
control levels can be recalled by pressing the NORMALIZATION @key on
the REMOTE CONTROL TRANSMITTER.
@,... DISPLAY~
The POSITION in present selection and the remaining time in use of setting
OFF timer are displayed on the screen by pressing the DISPLAY button.
To erase the display, press this button again.
@.... Headphone Jack
inserting the headphone (option) to the outlet provides personal listening, (or
recording purpose with the appropriate lead. )The TV set speaker is automati-
cally switched off. –2–
,-..
;.
,..
..
.,-.
,-.
. .
,.
,.
i“
,.. .
:..
i-“
,,.
‘...
;’ $“
,...
..
:.+.
+“
,- . .
1, -
. .
..
. . .
!“
‘.,
&..
.,. .
:.
“.
r.-
:. ,
::,-
:.
,.,.
...’
. .
1’.
. . . . . .

AUTO SHUT OFF
This TV set incorporates the AUTO SHUT OFF function which automatically
switches OFF the TV set, and switches it to the standby mode about 10 min-
utes after aTV broadcast finishes or there is no longer aTV signal. Thereafter,
the TV set will not switch ON even if the TV signal is input. TO switch the TV
set ON, usethe power ON/OFF witch- on the remote control transmitter.
The remaining time for AUTO SHUT OFF is displayed on the
screen.
Remaining time
G
Remote ControfOperation
SPECIAL KEY
VCR po (SPECIAL Key is used for the
(This bu SPECIAL FUNCTIONS setting.
aProgra Refer to the item of the
too. )SPECIAL FUNCTIONS.)
Program CHANNEL SCANNING
ALT (Alternate)
so IN ETUNING
co .V./Vl DEO Selector
BR ECALL
co FF TIMER
so Power ON/OFF
ORMALIZATION
Main ON/OFF switch of the TV set must be in “ON” position before remote
control operation is possible.
Point transmitter towards the TV set, then press the appropriate function button
for the following controls.
●The keys on the Remote Control Transmitter operate in the sz~le manner as
those on the front of the television. In addition to those controls, the transmit-
ter has these additional functions: Programme Selection (direct selection),
NORMALIZATION, Sound Mute, OFF TIMER, Alternate, RECALL, FINE
TUNING, CHANNEL SCANNING and SPECIAL KEY.
~,... Power ON/OFF u
press this button to switch TV set on. To switch TV set off, press again.
Note: The Standby and Power Indicator @will remain illuminated when the
TV set is switched off with this button. This is to indicate that the TV
set is still partially energized.
To disconnect TV set completely from mains, switch off with Main ON/OFF
switch on the T.V. set itself.
–3–
. .. ..... . ..
,.
.-.. . . . .
-,,
-. . .....-- ”””.”. “’: .-”.’ ..-,<.. ..........

~.... Programme selection
●For selection of the programme number 1to 9, press the programme selec-
tor button ~.
.For selection of the programme number 10 to 19 or 20 to 29, press the “l-” ‘
or “2-” button and then press the “O” to “9” programme selector button
~within five seconds.
@.... VCR Position Selector (This button serves as a Programme Selector, too.)
When using aVCR connected to the aerial socket, VCR Position must be
selected by pressing this button.
.Each time the VCR Position Selector @is pressed, the VCR Position
number will change as follows: VCR1 —VCR2 —VCR3
●The characters of “VCR1”, “VCR2” or “VCR3” are displayed on the screen.’
@.... RECALL ~{:3
The POSITION in present selection and the remaining time in use of setting-----
OFF timer are displayed on the screen for 5seconds by the RECALL Key,
NOTE: The RECALL Key has asa-me function as the SPECIAL Key @,
(When the RECALL Key is pressed for more than 2.5 seconds, “SP--”
is display ed.,on the screen. )
@.... NORMALIZATION +.+
When this button is pressed, automatically SOUND VOLUME, CO LOUR,
BRIGHTNESS and CONTRAST are set at the levels which have been memo-
rized by the MEMORY ~button.
@.... Sound mute ~
Should you wish to mute the sound (e.g. While talking on the telephone).
Press this button once. To switch the sound back on, press it again.
0....0 FFTIMER Q
After aset time has elapsed, the power of the T.V. receiver is switched off
automatically. Each time the key is pushed, the set time changes as follows:
Channel number display +30minutes +60minutes +90minutes+ 120minutes
4
With the off timer being set and the channel display reset, the remaining time is
displayed by pushing the off timer key again. When the key is pushed again within
three seconds after the key was first pushed in above manner, the time is set to a,~~-’,--,
upper time which is most close to the remaining time. .)’
●Just one minute before switching off, “-01” and programme number you are
watching are displayed on the screen.
.The timer setting will be cancel led if the power is switched OFF.
0
.... ALT (Alternate)
Press the “ALT (Alternate)” button @and the T.V. set will alternately select
the previous channel and the present channel. For example, now you are
watching channel 4but you watched channel 2previously. If you press the
“ALT Key”, channel 2immediately appears then channel 4is stored in the
memory.
.... FINE TUNING < >
For tuning of the best picture and sound, press the (t) Fine Tuning button.
.The programme number is displayed on the screen when the FINE TUNING
buttons are depressed. Display time continues while these buttons (~) are
depressed and for 5seconds after detaching them.
–4–

(REMOTE CONTROL OPERATION continued)
@....etiANNELscANNING
Press the CHANNEL SCANNING Key @to search for aprogramme. The
channel positions are automatically scanned, and the channel scanning will stop
at the position where it began. To stop at the position you want, press this
key again,
ON-SCREEN DISPLAY: EXAMPLE
settime4dm
●C)FF TIMER
●SOUND MUTE
n
Display time
dSOUND MUTE continues for
----- ------ ---
Video/Audio Input Connection
●NORMALIZATION
In order to watch the playback from aVCR, video disc player or the video signal from a
video camera, the output terminal, of the A,V. equipment in use must be connected to the
VIDEO/AUDIO INPUT terminal. Note that
VIDEO mode to watch any A,V. program.
(REAR PANEL)
VIDEO CAMERA
~
the T. V./Vi DEO switch must be set to the
VIDEO/AUDIO Input level
~AUDIO INPUT 436rnVrms More than 40kQ
VTR AuDIO. IN
VIDEODISC PLAYER
LJ
NOTE: In the VIDEO mode, you can select the T.V. program me. -
.If you wish to select the programme number “7” in the ViDEO mode (while watching
the playback from aVCR);
~Select the programme number “7” by the Programme Selector button ~or=.
i
mPress the T. V./Vi DEO Selector ~, and
the picture of the programme number
“7” will appear. Dprogrammen:er
SCREEN DISPLAY
A.V. (Audio Video) connection to the Aerial socket
The A.V. apparatus can also be connected to the aerial socket of your T.V. receiver. In this
case, it is advisable to select the “VCR1”, “VCR2” or “VCR3” position for the best
picture by the VCR Position Selector @.
VCR Position is specially designed for the VCR playback. The picture of the VCR play-
back may be distorted in other position.
For further details concerning this connection and adjustment, “refer to the operating
instructions for the A.V. apparatus.
–5–

Pre-Setting of Stations up to 32 broadcast statlOnS In your reception area i
can be stored in the electronic memory,
m
mSet the ~PRESET switch to ON position.
Select the programme number (with programme selector button @or ~) for which
you would like to preset aprogram.
Set the ~BAND SWITCH to the channel band corresponding to your desired
channel.
Channel band VL, VH and Uare for the following channel groups.
VHF range
Band VL Channels 1—3
Band VH Channels 4— 10
UHF range
Band UChannels 21 – 69
The channel (VL, VH or U) Band is displayed on the screen.
‘t.
REMARKS .
SCREEN DISPLAY
Pranne,
number band
When the band is set using the BAND SWITCH, the frequency will be set to the lowest
frequency in the set band.
ml Press and hold the @(+) SEARCH button to station searching.
When astation is found, release the (+) SEARCH button as soon as picture appears.
When searching stops, the TV picture and sound will probably be rough.
Press and hold the @(+) FINE TUNING button until both picture and sound rece~- :‘
tion clear.
REMARKS
The lowest bar display changes according to
If the station found in above step is not the
again until the desired station appears.
UP/DOWN of
one to be set,
tuning voltage.
press the (+) .SEARCH BUTTON
~Once the best picture have been obtained, press the @MEMORY button to store the
~station located by the tuning in the electronic memory.
~Repeat steps ❑-❑for remaining program numbers to be set.
~Be sure the OPRESET switch is in OFF position.
When the PRESET switch is switched OFF, BAND SWITCH, the (+) and (–) sEARCH
buttons will not function.
Memory Copy
This T.V. tuning system has another advanced feature called “memory COPY”.
Astation entered into the memory at aparticular programme number can also be received
at any other programme number, to use this feature follow the procedure below.
If you wish to copy the T.V. channel in the programme number “2” into the program~e
number “15”.
1. Select the programme number “2”. (with the prog. selector @or m.)
2. Turn the PRESET switch~ ON.
3, Select the programme number “15”. (with the prog. selector @or m.)
4. Press the MEMORY button~, set the PRESET switch~ to OFF.
–6–
. . .. . . . . .. .. . . ...... . .... ............ .. .... . .
.-.
..-”
..
”,-< ..’

Special
.You can set
Functions
the SPECIAL FUNCTIONS to input the SPECIAL CODES using the SPE-
CIAL Key @and the Programme Selector ~of the remote control transmitter.
The SPECIAL CODES and SPECIAL FUNCTIONS are as follows.
F
SPECIAL
CODE .
F
71
72
I
L90
SPECIAL FUNCTIONS
.
RE-SET ALL SPECIAL FUNCTIONS
SEARCH FOR CHANNEL SCANNING
MEMORY DELETE FOR’CHANNEL SCANNING
(Used to delete aprogramme position from the channel scanning positions.)
MEMORY ADD FOR CHANNEL SCANNING
(Used to add aprogramme position to the channel scanning positions.)
SECRET POSITION (SET AND RE-SET)
(Usedto restrict the viewing of some programme positions. )
NOTE: Special functions are not cancelled when the power is turned off or when the AC
power plug is disconnected from the mains.
.,.-,.
‘)
<!, ,.J..
-. ‘:-:., ;f
–7–
-. . . . . . -. ...... . .. . ..- .,.-.:,.... ... .
..-. ““ . . . .. .. . . .. . . . ,.,

~SETTING OF THE SECRET POSITION
(SPECIAL CODE “90”)
●The SECRET POSITION is used to restrict the viewing of programme positions that you
do not want others to watch.
.Any positions can be set as the SECRET POSITIONS.
EXAMPLE
HOW to set the SECRET POSITION at programme position “15”.
III
El
•I
❑
..
Select programme position “15“ using
the Programme Selector@ or=.
Press and hold the SPECIAL Key @of
the remote control transmitter for more
than 2.5 seconds. “SP--” will be display-
ed on the screen.
Input the SPECIAL CODE “90” using
the Programme Selector= of the re-
mote control transmitter.,
Press t!~e MEMORY button @in the
front control section of the TV set.
The picture will then disappear, and
“X 15” will be displayed on the screen.
El 15
msP— —
ESP90
rx15
The SECRET POSITION setting is now completed.
When position “15“ isselected using the Programme Selector@ or ~after the SECRET
POSITION setting has been completed, only the characters “X 15” wiJl appear.
HOW TO WATCH APROGRAMME ON THE SECRET POSITION: ~~
El
El
131
Select the SECRET POSITION (position “15”) using the
Programme Selector Qor=. l___4
Press and hold the SPECIAL Key @of the remote con-
trol transmitter for more than 2.5 seconds. “SP--” will be
displayed on the screen. nsP— —
II
Input SPECIAL CODE “90” using the Programme Selector 11
~of the remote control transmitter.
The programme of the SECRET POSITION will then
appe2r. Next, press the SPECIAL Key @, and “SP90” I_____J
SP90
will disappear.
NOTE: If you watch aprogramme on the SECRET POSITION, then select another pro-
gramme position, you will have to repeat the above procedures before you can
watch aprogramme on the SECRET POSITION again.
As many SECRET POS
,.
;,.
.,”.
~.
:.
:.-
-,
,..
.-
W.
. .
.:
,.;
i’
>
....
..
., ‘
.
. .
TIONS as you want can be set. “,
–8– -.. .. .. .. . .. . .
,,,
.- . . . ...”. ..

HOW TO RE-SET THE SECRET POSITION:
.This is done in the same manner as the SECRET POSITION setting.
For example, to re-set programme position “15” in the SECRET POSITION:
El
.
-. El
El
El
Select programme-position “I 5“ (SECRET POSITION) using the Programme Selector
Oorm.
(“X 15” will be displayed on the screen.)
Press and hold the SPECIAL Key @of the remote control transmitter for more than
2,5 seconds.
(“SP--” will be displayed on the screen.)
Input SPECIAL CODE “90” using the Programme Selector ~of the remote con-
trol transmitter.
Press the MEMORY button @of the front control section of the TV set.
Position “15” is now re-set in the SECRET POS
*.
TION.
h
SEARCH FOR THE CHANNEL SCANNING
(SPECIAL CODE “70”)
When SPECIAL CODE “70” is input, all the programme positions are automatically
scanned, and the active programme positions are stored in memory.
Once this programming is completed, the TV receiver will select only the stored pro-
gramme positions when the CHANNEL SCANNING Key @is pressed.
HOW TO INPUT SPECIAL CODE “70”: [
❑
El
•1
Press and hold the SPECIAL Key @of
the remote control transmitter for more
than 2.5 seconds. L_4
(“SP..” wil[ be displayed on the screen. )
Input SPECIAL CODE “70” using the
Programme Selector ~of the remote
control transmitter. ESP70
Press the MEMORY button @. The programme positions are then automatically scan-
ned, and the active programme positions are stored in memory.
The channel scanning will then stop at the position where it started scanning.
SEARCH FOR CHANNEL SCANNING is now completed.

ZMEMORY DELETE FOR CHANNEL SCANNING
(SPECIAL CODE “71”)
.This function is used to delete aprogramme position from the channel scanning posi-
tions, so it will not be scanned when the CHANNEL SCANNING Key @is pressed.
For example, to delete position “2” from the channel scanning positions:
❑Select programme position “2” using
the Programme Selector@ or=.
❑Press and hold the SPECIAL Key@ for m2
more than 2.5 seconds, and input SPE-
CIAL CODE “71” using the Programme
E
Selector ~of the remote control
transmitter. SP71
❑Press the MEMORY button ~of th~front control section of the TV set.
Position “2” is now deleted from the channel scanning positions.
Position “2” will be passed over when the CHANNEL SCANNING Key @is pressed.
■MEMORY ADD FOR CHANNEL SCANNING
(SPECIAL CODE “72”)
●This function is used to add aprogramme position to the channe
it will be scanned when the CHANNEL SCANNING Key @is pressed.
scanning pos tions, so
For
III
❑
❑
example, to add position “2” to the channel scanning positions:
Select programme position “2” using
the Programme Selector ~or=.
Press and hold the SPECIAL Key @for
more than 2.5 seconds, and input SPE- L
CIAL CODE “72” using the Programme
Selector ~of the remote control
transmitter. nSP72
Press the MEMORY button @of the front control section of the TV set.
Position “2” is now added to the channel scanning positions.
Position “2” will be scanned when the Channel Scanning Key @is pressed.
—lo–

■RE-SET ALL SPECIAL FUNCTIONS
(SPECIAL CODE “01 “)
.When SPECIAL CODE “01” is input all the special functions are re-set.
HOW TO INPUT THE SPECIAL CODE:
❑Press and hold the SPECIAL KEY@ for
more than 2.5 seconds, and input SPE-
CIALCODE”O1” using the Programme DSPO1
Selector m.
~Press the MEMORY button~ of the front control section of the TV set.
I~~
~.j$ljj All the special functions are now re-set.
NOTE: The SPECIAL FUNCTIONS can also be cancelled by inputting SPECIAL CODE
“00”. *.
When SPECIAL FUNCTIONS are cancelled using SPECIAL CODE “00”, the
start condition for~ power is changed to the standby start condition, meaning
that the picture will not appear even when the MAINS ON/OFF Switch Oisset
to the on position. To turn on the lV set from the standby mode, press ~, @
@button.
SPECIAL CODE “00” is input in the same manner as SPECIAL CODE “01”.
1,
~.<;.,,: ‘.?
.,
...

10THER SPECIAL FUNCTIONS
)The start condition for TV power can be changed by inputting SPECIAL CODE “50’”
or “51”.
!VHEN SPECIAL CODE “50” IS INPUT
BEven if the Mains ON/OFF Switch Ois set to the on position, the picture
will not appear. (The lVset remains in the standby mode.) To turn on the TV
set from the standby mode, press ~. @or @button.
nputiing SPECIAL CODE “50”: I1
Pres~ and hold the SPECIAL Key@ for
more than 2.5 seconds, and input SPE-
CIAL CODE “50” using the Programme u
Selector ~.
Press the MEMORY button @on the front controls of the TV set
OTE: To return to TV’s power ~tart condition to its original condition, input SPECIAL
CODE “51 “.
SPECIAL CODE “51” is input in the same manner as SPECIAL CODE “50”.
–12–

HELPFUL HINTS
NO PICTURE, NO SOUND POOR PICTURE, SOUND OK
.Check if TV is plugged in. .Adjust BRIGHTNESS control.
.Try adifferent channel, ●Adjust FINE TUNING control.
if OK, probably station trouble. .Check aerial connections.
NO COLOUR, PICTURE OK WEAK PICTURE
.Adjust CO LOUR control. ●Check aerial connections on back of set.
.Adjust FINE TUNING control. .Check aerial for broken wires.
.Is the program in colour? .Re-orient aerial.
The following faults are not caused by the receiver.
“GHOSTS”
Reflections of signals from mountains or high buildings will cause multiple images, called
“Ghosts”. $,
These abnormal conditions can be reduced” to minimum by repositioning aerial or by
installing new one suited for your area.
i
“INTERFERENCE”
Interference may be caused by electrical appliances, car ignition systems, etc. This should
normally be atemporary condition, but should this interference persist, contact your
dealer.
Slots and openings in the cabinet and in the back or bottom are provided for ventilation,
and to ensure reliable operation of the television receiver and to protect it from overheat-
ing, these openings must not be blocked or covered.
BATTERY INSTALLATION (REMOTE CONTROL TRANSMITTER)
~Remove the battery cover by sliding.
~Install two “AA” 1.5 volt batteries so that the “+” and “-” marks on the batteries
match the “+” and “-” marks inside the unit.
~CIose the battery cover.
NOTE:
Replace the batteries when the T.V. set is showing the following symptoms: Operation is
unsteady or erratic, sometimes the T.V. set does not work with remote control transmitter.
Discharged batteries may leak and damage the unit. The normal life of batteries should be
from nine to ten months.
–13–
. . . .- ..” ., --- ,.. .. . . .
.’. .

MOUNT NG TELESCOPIC AERIAL
(Model CZP6012: Telescopic Aerial is an optional extm. )
4P-
fvIATCHING “TO THE
BOX AERIAL
SOCKET
,’.
Telescopic
u
UConnect the telescopic Aerial
Aerial /feeder to terminal on matching
feeder box.
NOTE:
When using an outdoor aerial, disconnect the ..;,
telescopic aerial feeder. ,$?:?+-
‘%+.-.~
Then connect the outdoor aerial feeder to
te[minal on matching box.
.
,-
-. . ,:.. 1
‘.:-,.-..4
.-y
1;
–14–

,,
AERIAL
The type of aerial required depends on factors such as the site, its distance and direction
from the transmitter, local interference etc. Your dealer will advise you the best type of
aerial to be used.
The aerial socket is on the back panel of the TV set.
MAINS SUPPLY
The receiver is designed to operate on an A.C. mains supply of 230 volts 50 Hz.
SPECIFICATIONS
Power Source . . . . . . . . . . . . . . AC230V,50HZ
Television System ........... System B/G
Colour System . . . . . . . . . . . . .PAL
Channel Coverage ........... VHF: 1-10
UHF: 21 –69
Aerial Input Impedance ....... 75 ohm
s*O
Part No. 4AA6P1OO144- -E2HJ (A3-A) SANYO Electric Co., Ltd.