Sapphire Audio Upholstery Pro User manual

07-01713B 2010-05 1 Sapphire Scientific
Upholstery Pro
User Instructions
The Upholstery Pro cleaning tool provides deep, rapid penetration of cleaning solution and
simultaneous high volume extraction. Lightweight, easy to use, and adjustable for a wide range
of fabrics and soiling conditions, the Upholstery Pro produces cleaner, drier fabrics.
Patent Pending
READ AND SAVE THESE INSTRUCTIONS
Key features
•Comfortable handle and highly flexible vacuum hose
provides relaxed balanced handling and
substantially reduces operator fatigue
•In-line solution strainer helps prevent clogging
•High pressure injector glide provides deep, even
penetration of solution into fabric surface
•Unique dual extraction slots permit full extraction in
both directions across fabric surfaces
•Solution control valve provides precise control for
widest range of fabric types and soiling conditions
•Sliding vacuum release allows for easy vacuum
adjustments on the fly
INITIAL SETUP
Connect the front quick-connect solution line to the wand
coupling and slide the front vacuum hose cuff (Fig. A, 5)
firmly over the ribbed hose receiver. The Upholstery Pro
is now ready to be attached to your extraction
equipment.
USING THE UPHOLSTERY PRO
1. Connect the rear quick-connect solution line to the
extractor solution line
2. Attach the rear hose coupling either to 1½ in i.d.
(coupling fits over hose) or to a 2 in. i.d. (coupling fits
inside hose).
3. Turn on extractor.
4. Squeeze the trigger lever to release the solution and
begin cleaning. The sliding trigger lock may be used
to hold the trigger valve in the open position.
5. Use the flow adjustment valve (Fig. A, 4) to adjust
solution flow and the vacuum release slide (Fig. A,
1) to adjust the strength of the vacuum.
WARNING: Flow adjustment valve
assembly can become extremely hot
during use. Keep valve wrap closed.
Tips for Use
Solution control. Adjust flow according to the fabric
type, absorbency and degree of soiling. Lightweight or
delicate fabrics require less solution volume than
3. Insulated adjustment
valve wrap
2. Front solution line
quick-connect coupling
5. Front vacuum
hose cuff
4. Flow adjustment
valve (inside cover)
7. Rear vacuum hose
cuff. Cuff fits over
1½ in. hose or inside
2 in. hose.
FIG. A: HEAD, VACUUM HOSE AND
SOLUTION LINE ASSEMBLY
6. Rear solution line
quick-connect
coupling (not shown)
1. Vacuum
release slide

07-01713B 2010-05 2 Sapphire Scientific
FIG. B: HEAD ASSEMBLY
3. Cover
screws (×4)
1. Vacuum
release slide
6. Glide and O-ring seal
(S13-01705)
5. Glide screws (×4)
Remove upper cover first.
4. Trigger valve
body (23-070)
2. Upper
cover
heavier, more absorbant materials. The Solution Flow
Guide diagrams (Fig. E) provide a rough guide for light,
medium and maximum flow adjustments.
Vacuum control. Use the vacuum release slide (Fig. B,
1) to control the strength of the vacuum when extracting
thin, delicate or lightweight fabrics.
For best results, use the Upholstery Pro with Sapphire
Scientific cleaning chemicals.
For more information about cleaning with the Upholstery
Tool, visit www.sapphirescientific.com.
MAINTENANCE
Daily: Rinse the hand tool by running clean water
through the solution line.
Daily: Check the glide assembly (Fig. C, 6) for steady,
even flow of solution through the injector nozzles. If any
of the injector ports appear clogged, use a small needle
to remove the obstruction, taking care not to damage the
glide. If the glide is scratched, gouged, snags on
carpets, or flows excessively, it may need to be replaced
(see “Servicing the glide,” below). Replacement glide
assemblies are available from your distributor.
As needed: Lubricate the quick-connect couplings
(Fig. C, 3; Fig. A, 6) with a small amount of rust-inhibiting
oil such as LPS-3.
As needed: Lubricate trigger valve stem (Fig. F) with
a small amount of synthetic heavy duty grease. To
grease the stem, follow these steps.
1. Remove the trigger lever nut and bolt from the
trigger lever and remove lever.
2. Unscrew stem retention nut and lift out stem
assembly. Apply a small amount of grease to the
stem.
3. Replace stem assembly and retighten retention nut.
Reattach trigger lever.
As needed: Clean the inline strainer (Fig. D, 2) when
solution flow is visibly reduced. To clean the filter, loosen
the strainer assembly nut, and remove the strainer and
strainer washer. Rinse these items in clean water and
reassemble the strainer. It is not normally necessary to
replace the inline filter element. Be sure to include the
nylon washer when reassembling, and take care not to
over-tighten the strainer assembly nut.
To maintain appearance, wipe exterior surfaces with a
damp cloth.
FIG. C: HEAD (BOTTOM VIEW)
4. Vacuum cuff
attachment
1. Trigger lever
6. Glide
2. Trigger lever lock
3. Front quick-
connect coupling
5. Trigger lever nut
and bolt
FIG. D: FLOW ADJUST ASSEMBLY
3. Hex nut. Loosen
here to access strainer.
1. Control knob
5. Washer
(24-002)
4. Orifice plate
(20-035) 6. Rear quick-
connect coupling
2. Inline strainer
(20-006)
(s13-01698)

07-01713B 2010-05 3 Sapphire Scientific
SERVICING
The Upholstery Pro is designed to allow easy in-
the-field service to the glide and the trigger
valve with basic hand tools in just a few
minutes. If replacement becomes necessary,
rebuild kits and replacement parts are available
from your Sapphire distributor or from Sapphire
Scientific at 800-932-3030.
Replacing the glide
Have on hand a Glide and O-ring replacement
kit (part no. S13-01705).
1. Remove the four cover screws (Fig. B, 3)
and lift off the cover.
2. Remove the four glide screws (Fig. B, 5)
and remove the glide and the O-ring seal. Discard.
3. Install new O-ring into sealing edge of new glide. Put
new glide into head. Make sure that the O-ring is in
place.
4. Replace glide screws and tighten; then replace
cover and tighten with cover screws.
Servicing the trigger valve
If the trigger leaks or no longer releases sufficient
solution and you have determined that the glide is not
plugged or damaged (see “Check Glide Assembly,” p. 2)
the trigger may need service. Two repair options are
available.
Option A: Rebuild the trigger valve.
A stem replacement kit (part no. 48-064) is available
from your Sapphire distributor. The parts included in this
kit are shown in Fig. F.
1. Remove the nut and bolt from the trigger lever and
remove the lever.
2. Unscrew stem retention nut and lift out stem
assembly.
3. Install the stem assembly and retighten the stem
retention nut.
4. Replace cover and reinstall trigger lever. Use the
new lock nut provided (Fig. F, 3).
Option B: Replace the trigger valve assembly
A replacement trigger valve assembly (part no. 23-070)
is available from your Sapphire distributor.
1. Remove the four cover screws (Fig. B, 3) and lift off
the cover.
2. Depress the hose release ring on the solution outlet
tube and pull out the tube. Avoid kinking the tube.
3. Remove the solution outlet tube fitting from the valve
body.
4. Disconnect the solution inlet hose assembly from the
valve body.
5. Valve body and trigger will now drop free.
6. Insert new trigger valve valve assembly and reinstall
solution outlet tube and solution inlet hose
assembly.
7. Replace cover.
REPLACEMENT PARTS
The following replacement parts are available from your
Sapphire Scientific distributor:
Description Drawing
reference
Replacement
part no.
Trigger and valve body Fig. B, 4 23-070
Glide and O-ring seal Fig. B, 6 S13-01705
Strainer, 50 Mesh Fig. D, 2 20-006
Orifice Fig. D, 4 20-035
Washer Fig. D, 5 24-002
Stem replacement kit Fig. F 48-064
1. Stem retention nut
FIG. F: STEM REPLACEMENT KIT (48-064)
2. Stem.
Periodically
apply grease
6. O-ring seal
5. Teflon seal
7. Extractor spring
3. Trigger lever lock nut
8. Shoulder screw
4. O-ring seal
FIG. E: SOLUTION FLOW GUIDE
1. Light 2. Medium 3. Maximum
Solution
Vacuum
slots
Stem Replacement Kit
48-064
use part# MP-RV4NT-
EA
Stem Replacement Kit 48-064
use part# MP-RV4NT-EA
Vac hose 9ft s13-01700
Vac Hose 1ft s13-01701
Solution hose
ss-1822101-ea

07-01713B 2010-05 4 Sapphire Scientific
SPECIFICATIONS
Model Sapphire Scientific Upholstery Pro
Part no. 67-019
Dimensions Head: 4 in. extraction width
Hose assembly: 10 ft.
Construction
Head: High performance nylon resin.
Glide: Engineering thermoplastic
Hose assembly: High-flex vacuum hose
Fittings: Brass with high-temp seals
Specifications are subject to change without notice. Some
values may be approximate.
WARRANTY
Warranty information is available from your Sapphire
Distributor or at www.sapphirescientific.com.
Warranty registration
Visit www.SapphireScientific.com to register your
purchase. Registration allows us to better assist you with
using, maintaining or servicing your equipment, as well
as to contact you in case we have important safety
information concerning your Sapphire Scientific product.
If you determine service is required, have your
equipment model, serial number and original proof of
purchase available and call your distributor for
assistance with obtaining a return material authorization
(RMA).
CONTACT
Sapphire Scientific
2604 Liberator
Prescott, AZ 86301
800-932-3030 www.sapphirescientific.com

15
16
1
10
7
2
9
8
3
16
11 12
6
5
4
12
11
13
SEE VACUUM RELEASE DETAIL
14
CUT LENGTH: 3.25 INCHES
VACUUM RELEASE DETAIL
2
(TYP 2 PLACES)
12
11
14
NOTES:
APPLY THREAD SEALING COMPOUND ON ALL NPT THREADS 1.
APPLY INSTANT ADHESIVE (LOCTITE 454 OR EQUIV) ALL AROUND BOTTOM OF RECESSED POCKET AND 2.
SECURE WITH SCREW. AVOID EXCESS GLUE OVERRUN
BUBBLE TEST ALL FITTINGS USING COMPRESSED AIR 3.
A
B
REVISIONS
REV ECO DESCRIPTION CHG'D DATE
A 1578
QTY OF 13-01692 WAS .25 FT; RELEASE TO
PRODUCTION
LW 4/14/10
B 1632 03-01668 (ITEM 6) WAS 03-01637 LW 10/27/10
416
03-01655 SCREW - #6-32 X 1/2 PHP SS
4 15 03-01654 SCREW - #6 X 1/2 AB PHP SS
2 14 03-01653 SCREW - #4 X 1/4 AB PHIL CH SS
113
03-01642 WASHER - SEALING 3/8 X 3/4 OD SS/NEOPR
212
13-01686 VACUUM RELEASE - TOP ACETAL BLK
211
13-01687 VACUUM RELEASE - BOTTOM ACETAL BLK
110
03-01638
COUPLING - 1/4 QUICK DISCONNECT NIPPLE X 1/8
F NPT SS
.27 FT
9 13-01692 HOSE - 1/8 OD X .023 WALL ETFE
18
03-01640 FITTING - 1/8 NPT X 1/8 OD PUSH TO CONNECT
17
13-01691
HOSE ASSY - 3/16 DIA 1/8 NPT X 1/8 NPT X 5.50
LONG
16
03-01668 O-RING - 2.239 ID X 2.379 OD X .07 THK VITON
15
13-01683
BODY - BOTTOM HALF UPHOLSTERY TOOL NYLON
FISHER BLU
14
13-01682
BODY - TOP HALF UPHOLSTERY TOOL NYLON FISHER
BLU
13
03-01639 FITTING - #10-32 X 1/8 OD PUSH TO CONNECT
1 2 13-01690 VALVE ASSY - PMF V4N WITH TRIGGER
11
13-01684 MANIFOLD - UPHOLSTERY TOOL ACETAL BLK
QTY ITEM PART NO. DESCRIPTION
This drawing and the information contained thereon
is proprietary to DRI-EAZ PRODUCTS, INC. and shall
not be released to any party without the express
written consent of DRI-EAZ.
-
-
THIRD ANGLE PROJECTION
TITLE:
UNLESS OTHERWISE
SPECIFIED:
ALL DIMENSIONS ARE
IN INCHES [mm]
TOLERANCES:
1 PLC. = ±.1 [2.5]
2 PLC. = ±.03 [.75]
3 PLC. = ±.010 [.25]
4 PLC. = ±.0050 [.125]
ANGULAR = ±1°
LW
RP
1/11/10
1/11/10
B BF436
DRI-EAZ PRODUCTS INC.
15180 JOSH WILSON RD
BURLINGTON, WA 98233
PH: [phone]
DATE
CHK'D BY:
DATE
DR BY:
SIZE
NEXT ASSEMBLY:
REV
(UPHOLSTERY PRO)
HEAD ASSEMBLY
SHEET 1 OF 1
SCALE: 1:1.5
DWG NO.
13-01688
LIST OF MATERIALS
Complete cover (top and bottom) for portable and
truckmount tool DP-S567-EA