Satel ETHM-1 Plus User manual

Ethernet communication module
ETHM-1 Plus
Firmware version 2.03 ethm1_plus_en 06/16
SATEL sp. z o.o.
ul. Budowlanych 66
80-298 Gdańsk
POLAND
tel. + 48 58 320 94 00
www.satel.eu

WARNINGS
The module should be installed by qualified personnel.
Read carefully this manual before proceeding to installation.
Changes, modifications or repairs not authorized by the manufacturer shall void your rights
under the warranty.
FreeRTOS is used in this device (www.freertos.org).
SATEL's goal is to continually upgrade the quality of its products, which may result in some
changes of their technical specifications and firmware. The current information on
the introduced modifications is available on our website.
Please visit us:
http://www.satel.eu
The declaration of conformity may be consulted at www.satel.eu/ce
The following symbols may be used in this manual:
- note;
- caution.

CONTENTS
1General.............................................................................................................................2
2Field of application............................................................................................................2
3Electronics Board..............................................................................................................3
4Setting address.................................................................................................................3
4.1 Module connected to INTEGRA / INTEGRA Plus control panel................................4
4.2 Module connected to VERSA control panel...............................................................4
5Installation ........................................................................................................................4
6Configuring the settings....................................................................................................6
6.1 Module connected to INTEGRA / INTEGRA Plus control panel................................6
6.1.1 Module parameters and options.........................................................................6
6.1.2 IP filter................................................................................................................9
6.1.3 User functions ..................................................................................................11
6.1.4 Virtual keypad...................................................................................................12
6.1.5 Macro commands.............................................................................................13
6.2 Module connected to VERSA control panel.............................................................21
6.2.1 Module parameters and options.......................................................................21
6.2.2 Messaging........................................................................................................24
7Remote programming / operating of control panel via Ethernet......................................25
7.1 GUARDX program...................................................................................................25
7.1.1 Configuring the GUARDX program settings.....................................................26
7.1.2 Initiating connection from GUARDX program...................................................27
7.1.3 Initiating connection from keypad (through control panel)................................28
7.1.4 Establishing connection via the SATEL server.................................................28
7.2 Web browser ...........................................................................................................28
7.2.1 ETHM-1 Plus module settings..........................................................................28
7.2.2 Configuring computer.......................................................................................29
7.2.3 Establishing the communication.......................................................................29
7.3 Mobile device...........................................................................................................30
7.3.1 Configuring the settings in INTEGRA CONTROL application (Android)...........30
7.3.2 Configuring the settings in INTEGRA CONTROL application (iOS) .................34
7.3.3 ETHM-1 Plus module settings..........................................................................35
7.3.4 Establishing the communication.......................................................................35
8Specifications .................................................................................................................36

2 ETHM-1 Plus SATEL
1 General
The ETHM-1 Plus module enables the INTEGRA Plus, INTEGRA and VERSA alarm control
panels to communicate via the Ethernet network. The data transmission is encrypted by
means of an advanced algorithm based on 192-bit key.
The module firmware can be updated using the application available on www.satel.eu
2 Field of application
•Control panel configuration using the DLOADX program from a computer with Internet
access.
The feature is available for the INTEGRA Plus, INTEGRA (firmware version 1.03 or newer) and VERSA
(firmware version 1.01 or newer) control panels.
•Management of the alarm system using the GUARDX program from a computer with
Internet access.
The feature is available for the INTEGRA Plus and INTEGRA (firmware version 1.03 or newer) control
panels.
•Operation and configuration of the control panel using a web browser which supports
JAVA applications.
The feature is available for the INTEGRA Plus and INTEGRA (firmware version 1.03 or newer) control
panels.
•Operation and configuration of the control panel using the INTEGRA CONTROL /
MOBILEKPD / MOBILEKPD-2 / MOBILEKPD-2 PRO application from a mobile device with
Internet access. The mobile device acts as an additional keypad for the alarm system.
The feature is available for the INTEGRA Plus and INTEGRA (firmware version 1.03 or newer) control
panels.
•Operation of the control panel using the VERSA CONTROL application from a mobile
device with Internet access.
The feature is available for the VERSA (firmware version 1.04 or newer) control panels.
•Reporting events from the control panel to the monitoring station via the Ethernet network.
This contributes considerably to reducing the costs of reporting.
The feature is available for the INTEGRA Plus, INTEGRA (firmware version 1.04 or newer) and for the
VERSA (firmware version 1.01 or newer) control panels.
•Notification of events in the alarm system using e-mail messages. The message body is
generated automatically (it corresponds to the description in the event log in case of
INTEGRA Plus system).
The feature is available for INTEGRA Plus (firmware version 1.13 or newer) and VERSA (firmware version
1.04 or newer) control panels.
•Integration of the control panel with other systems, due to the open protocol for
communication over Ethernet. It is a dedicated solution for companies engaged in
integration of the object-oriented systems, which requires development of own software.
The feature is available for the INTEGRA Plus and INTEGRA (firmware version 1.06 or newer) control
panels.
For additional information on the open communication protocol, please visit
www.satel.eu

SATEL ETHM-1 Plus 3
3 Electronics Board
Fig. 1. Module electronics board.
terminals:
+12V - +12 V DC power input.
COM - common ground.
TMP - tamper input (NC) – if not used, it should be shorted to common ground.
A RS485 B - terminals provided for future applications (RS-485).
DTM - data (communication bus).
CKM - clock (communication bus).
RS-232 port.
PWR/LOG LED:
OK – power OK,
blinking – control panel being programmed or operated by means of the module.
BUS LED – blinking LED indicates that data exchange with the control panel is in
progress.
pins for setting the module address (see “Setting address”).
RJ-45 connector for Ethernet network. It is provided with two LEDs:
green – indicates connection to the network and data transmission,
yellow – indicates negotiated transmission rate (ON: 100 Mb; OFF: 10 Mb).
4 Setting address
To set an address, you must place jumpers across the ADDRESS pins. Table 1 shows how
to use jumpers in order to set a specific address ( - jumper on; - jumper off).

4 ETHM-1 Plus SATEL
Address 0 1 2 3 4 5 6 7
Pins status
Table 1.
4.1 Module connected to INTEGRA / INTEGRA Plus control panel
Set an address in the module within the range:
•from 0 to 3, if it is connected to INTEGRA 24 or INTEGRA 32 control panel,
•from 0 to 7, if it is connected to another INTEGRA or INTEGRA Plus control panel.
The address set must be different from that in the other devices connected to the keypad bus
of the control panel (the control panel does not support devices with the same address).
4.2 Module connected to VERSA control panel
Set address 4 in the module. No keypad with the address 4 may be connected to the control
panel.
5 Installation
Disconnect power before making any electrical connections.
The device is designed to be used only in the local area networks (LAN). It must
not be connected directly to the public computer network (MAN, WAN). For
establishing connection with public networks, use a router or xDSL modem.
The device is designed for installation indoors, in spaces with normal air humidity.
1. Secure the module electronics board in the enclosure. The module should be installed in
the same enclosure as the control panel. This will facilitate connecting the RS-232 ports
of control panel and module, which is required, if the control panel is to be configured via
Ethernet using the DLOADX program.
2. Set the module address (see “Setting address”).
3. Connect the +12V, COM, DTM and CKM module terminals to the control panel terminals
(Fig. 2). It is recommended that an unshielded non-twisted cable be used for making the
connection. If you use the twisted-pair type of cable, remember that CKM (clock) and
DTM (data) signals must not be sent through one twisted-pair cable. The wires must be
run in one cable.
Fig. 2. Connecting the module to the control panel.

SATEL ETHM-1 Plus 5
4. If the module is to supervise the enclosure tamper switch, connect the tamper switch
wires to the TMP and COM terminals. Otherwise, connect the TMP terminal to the module
COM terminal.
5. Connect the module to the Ethernet network. Use a cable compliant with the 100Base-TX
standard (identical as for connecting the computer to the network).
6. Power on the alarm system.
7. Start the identification function in the control panel (see the control panel installer
manual). The module will be identified as “ETHM-1”.
8. Configure the module (see “Configuring”).
9. If the control panel is to be configured via the module using the DLOADX program,
connect the module RS-232 port to the control panel RS-232 port. Depending on the
control panel, use the following cable to make the connection:
INTEGRA with connector socket of PIN5 type: PIN5/PIN5 (Fig. 3)
INTEGRA with connector socket of RJ / INTEGRA Plus type: RJ/PIN5 (Fig. 4)
VERSA: PIN5/RJ-TTL
The above mentioned cables are available in SATEL's product offering.
Fig. 3. Wiring diagram of the cable connecting RS-232 ports of ETHM-1 Plus module and
INTEGRA control panel with PIN5 connector socket.
Fig. 4. Wiring diagram of the cable connecting RS-232 ports of ETHM-1 Plus module and
INTEGRA / INTEGRA Plus control panel with RJ type connector socket.

6 ETHM-1 Plus SATEL
6 Configuring the settings
The module settings differ, depending on the control panel to which the module is connected.
6.1 Module connected to INTEGRA / INTEGRA Plus control panel
6.1.1 Module parameters and options
You can configure parameters and options of the module using:
•LCD keypad: SERVICE MODE STRUCTURE HARDWARE LCD KEYPADS SETTINGS
[module name],
•DLOADX program: “Structure” window “Hardware” tab “Keypads” branch
[module name] “ETHM-1” tab (Fig. 5).
Shown in square brackets are the names of parameters and options as they are presented
on the LCD keypad display.
Name – individual name of the device (up to 16 characters).
Tamper signaled in part. [Tamper in part.] – partition where alarm will be triggered in the
event of module tamper.
Obtain IP address automatically (DHCP) [DHCP] – if this option is enabled, the module will
automatically download data on IP address, subnet mask and gateway from the DHCP
server (in such a case, you do not have to program these parameters).
The IP address assigned to the module can be read:
−in the keypad: using the IP/MAC ETHM-1 user function available in the TESTS
submenu. For a detailed description of the function please refer to the user manual
for the control panel.
−in the DLOADX program: below the module parameters and options (Fig. 5).
IP address – module IP address.
Subnet mask [Netmask] – the mask of the subnet in which the module is working.
Gateway – IP address of the network device through which the other devices in the local
network can communicate with devices in other networks.
Obtain DNS server address automatically [DHCP-DNS] – if this option is enabled, the
DNS server IP address is downloaded automatically from the DHCP server. The option is
available, when the OBTAIN IP ADDRESS AUTOMATICALLY (DHCP) option is enabled.
DNS server – IP address of the DNS server which is to be used by the module. It can be
programmed, if the OBTAIN DNS SERVER ADDRESS AUTOMATICALLY option is disabled.
DLOADX
DLOADX->ETHM-1 connection [Connect DLOADX] – if this option is enabled, it is possible
to initiate connection with the control panel via Ethernet from the DLOADX program.
Port [Port (DLOADX)] – number of the TCP port used for communication with the DLOADX
program. You can enter values from 1 to 65535. The value must be different from that
entered for the other ports. Default value: 7090.
DLOADX key [Key (DLOADX)] – a string of up to 12 alphanumeric characters (digits, letters
and special characters) used for data encryption during communication between the
control panel and the computer with DLOADX program via Ethernet.
DLOADX server [DLOADX IP] – address of the computer running the DLOADX program. If
the computer is not in the same local network, it must be a public address. You can enter
either the IP address or the domain name.

SATEL ETHM-1 Plus 7
In the LCD keypad, the function for programming address of the computer with
DLOADX program is available in the user menu, CHANGE OPTIONS submenu (available
to service and administrators).
Fig. 5. DLOADX program: parameters and options of ETHM-1 Plus module connected to
INTEGRA / INTEGRA Plus control panel.
GUARDX / Java
GUARDX [Connect GUARDX] – if this option is enabled, it is possible to initiate connection
with the control panel via Ethernet from the GUARDX program.
WWW [Connect Intern.] – if this option is enabled, it is possible to initiate connection with the
control panel via Ethernet from the web browser.
GSM conn. [Connect GSM] – if this option is enabled, connection with the control panel via
Ethernet can be initiated from the INTEGRA CONTROL / MOBILEKPD / MOBILEKPD-2 /
MOBILEKPD-2 PRO application.
Port [Port (others)] – number of the TCP port used for communication with:
−GUARDX program,

8 ETHM-1 Plus SATEL
−JAVA application in the web browser,
−INTEGRA CONTROL / MOBILEKPD / MOBILEKPD-2 / MOBILEKPD-2 PRO in the mobile
device.
You can enter values from 1 to 65535. The value must be different from that entered for
the other ports. Default value: 7091.
WWW port – number of the TCP port used for communication with the web browser. You
can enter values from 1 do 65535 The value must be different from that entered for the
other ports. Default value: 80.
GUARDX/Java key [Key (others)] – a string of up to 12 alphanumeric characters (digits,
letters and special characters) used for data encryption during communication between the
control panel and:
−GUARDX program,
−JAVA application in the web browser,
−INTEGRA CONTROL / MOBILEKPD / MOBILEKPD-2 / MOBILEKPD-2 PRO in the mobile
device.
GUARDX server [GUARDX IP] – address of the computer running the GUARDX program. If
the computer is not used in the same local network, it must be a public address. You can
enter either the IP address or the domain name.
In the keypad, the function for programming address of the computer with GUARDX
program installed is available in the user menu, CHANGE OPTION submenu (available to
service and administrators).
PING test
PING test – if this option is enabled, the module can perform a communication test using the
ping command sent to the indicated network device. Parameters related to the
communication test should be programmed in the control panel:
LCD keypad: SERVICE MODE OPTIONS PING TEST,
DLOADX program: “Structure” window “Hardware” tab “Keypads” branch.
SATEL server
Connection via Satel server [SATEL server] – if this option is enabled, the control panel
connects to the SATEL server via the Ethernet module, while the SATEL server makes it
possible to establish communication with the control panel (Connection Establishing
Service). For communication vie the SATEL server, you do not need to additionally
configure the network device through which the module connects to the public network.
For establishing communication with the SATEL server, the DNS server must be used.
For communication via the SATEL server, the ports of 1024-65535 range are used as
outgoing ports. These ports must not be blocked.
Push notifications – if this option is enabled, the INTEGRA CONTROL application can
provide information about alarm system events by means of push notifications.
Integration
Integration [Integrate] – if this option is enabled, the module can be used for integration of
the alarm control panel with other systems.
Encrypted integration [Coded integr.] – if this option is enabled, communication with other
systems is encrypted. The integration encryption key should be programmed in the control
panel:
LCD keypad: SERVICE MODE OPTIONS INTEGRATE KEY,

SATEL ETHM-1 Plus 9
DLOADX program: “Options” window “Service” tab.
Port [Port (integr.)] – number of the TCP port used for integration. You can enter values from
1 do 65535. The value must be different from that entered for the other ports. Default
value: 7094.
Wrong login
Log event [Fail. – event] – if this option is enabled, all unauthorized attempts to connect to
the module are written to the event log.
Alarm [Fail. – alarm] – if this option is enabled, any unauthorized attempt to connect to the
module will trigger the tamper alarm. The option is available, if the LOG EVENT option is
enabled.
Information
MAC – module hardware address.
ID – identifier assigned to the module for the purposes of communication via the SATEL
server. The ID number is assigned automatically by the SATEL server.
IP – local address / public address of the module.
Refresh – pressing the button will update information presented in the MAC, ID and IP fields.
If the module is to be used in another alarm system, the hitherto used ID number must
be deleted. You can do it using the CHANGE ID function available from the keypad
(SERVICE MODE STRUCTURE HARDWARE LCD KEYPADS SETTINGS [module
name] CHANGE ID), if the control panel is connected to the SATEL server. Having
deleted the old ID number, the control panel will receive a new one. The INTEGRA
CONTROL applications using the old ID number will be unable to connect to the
control panel.
In the DLOADX program, the QR code for future use is displayed next to the settings.
6.1.2 IP filter
The module connected to the INTEGRA / INTEGRA Plus control panel with firmware version
1.15 offers IP filter. Using IP filtering allows you to enhance security level of the alarm
system. Establishing connection with the Ethernet module (alarm control panel) will only be
possible from defined IP addresses or subnets. You can configure the IP filtering settings
using the DLOADX program (“Structure” window “Hardware” tab “Keypads” branch
[module name] “IP filter” tab). IP filtering does not apply to communication with the
SATEL server.
You can configure IP filtering for the incoming connections:
•from DLOADX program,
•from GUARDX program (applies also to web browser and mobile application),
•as part of integration.
In each case you can define the filtering rules in one of the following configurations:
•up to 4 allowed IP addresses,
•1 allowed subnet and up to 2 allowed IP addresses,
•up to 2 allowed subnets.
To activate the filtering feature, enter a value in one of the four fields available for the
given type of incoming connections.

10 ETHM-1 Plus SATEL
Fig. 6. DLOADX program: “IP filter” tab.
IP Address – if the SUBNET option is disabled: the network address from which connection
with the Ethernet module can be established. If the SUBNET option is enabled: the IP
address used for defining the subnet from which connection with the Ethernet module can
be established.
subnet – if the option is enabled, you can define the subnet from which incoming
connections will be received by the module.
Subnet mask – mask used for separating the portion defining subnet from the IP address.
Filtering by IP address
In the IP ADDRESS field, enter the network address from which establishing connection with
the module (control panel) is to bed possible. The SUBNET option on the right-hand side of the
field must not be selected.

SATEL ETHM-1 Plus 11
Filtering by subnet
1. Select the SUBNET option. Description of one of the IP ADDRESS fields will change to
SUBNET MASK. From now on, the IP ADDRESS and SUBNET MASK fields constitute a pair.
2. Enter the address to be used to define the subnet.
3. Enter the mask to be used to separate the portion defining subnet in the IP address.
6.1.3 User functions
If the INTEGRA CONTROL / MOBILEKPD-2 / MOBILEKPD-2 PRO application is used in the
mobile device, the virtual keypad allows you to quickly start user functions after entering the
code and pressing an arrow key. The functions can be assigned to individual keys using:
•LCD keypad: SERVICE MODE STRUCTURE HARDWARE LCD KEYPADS SETTINGS
[module name]CODE+ARROWS,
•DLOADX program: “Structure” window “Hardware” tab “Keypads” branch
[module name] “User functions definition” tab (Fig. 7).

12 ETHM-1 Plus SATEL
Fig. 7. Program DLOADX: “User functions definition” tab.
6.1.4 Virtual keypad
The virtual keypad allows you to operate and program the alarm system in much the same
way as using a physical keypad. You can use the virtual keypad in the DLOADX and
GUARDX programs, web browser and in the mobile device (after installation of the INTEGRA
CONTROL / MOBILEKPD / MOBILEKPD-2 / MOBILEKPD-2 PRO application).
Parameters and options of the virtual keypad available in the DLOADX program can be
programmed using:
•LCD keypad: SERVICE MODE STRUCTURE HARDWARE LCD KEYPADS SETTINGS
DLOADX RS,
•DLOADX program: “Structure” window “Hardware” tab “Keypads” branch
“DLOADX (RS-232)” item.
Settings of the virtual keypad available in the GUARDX program, web browser or mobile
device can be programmed using:
•LCD keypad: SERVICE MODE STRUCTURE HARDWARE LCD KEYPADS SETTINGS
GUARDX ADDR.n [n = module address],
•DLOADX program: “Structure” window “Hardware” tab “Keypads” branch
[module name] branch “GUARDX/MobileKPD” item (Fig. 8).
For description of the keypad parameters and options, please refer to the programming
manual for INTEGRA / INTEGRA Plus control panel (only some of these parameters and
options are available for the virtual keypad).

SATEL ETHM-1 Plus 13
Fig. 8. DLOADX program: parameters and options of the virtual keypad available in GUARDX
program, web browser or mobile device.
6.1.5 Macro commands
The INTEGRA CONTROL / MOBILEKPD-2 PRO application allows to control the alarm system
by means of macro commands, thus making it possible to quickly and easily run a number of
different functions by touching just a few keys. The macro commands can be defined in the
DLOADX program (“Structure” window “Hardware” tab “Keypads” branch [module
name] branch “GUARDX/MobileKPD” item “Macro Commands” tab).
Defined macro commands can be automatically downloaded by the INTEGRA CONTROL /
MOBILEKPD-2 PRO application after establishing connection with the ETHM-1 Plus module.
Macro commands can be loaded into the application without establishing connection with the
module. The file containing macro commands can be exported, and then saved to the mobile
device memory (to transfer the file, you can use a memory card or other solutions available
for the given device). This method allows you to use macro commands defined for the
INT-KSG keypad in the INTEGRA CONTROL / MOBILEKPD-2 PRO application. Instead of a

14 ETHM-1 Plus SATEL
file with macro commands defined for the ETHM-1 Plus module, you can load a file with
macro commands defined for the LCD keypad.
The data related to macro commands are stored in the module memory. Before you
start defining the macro commands, click on the “Read” button in the “Macro
commands” tab to read the data from the module. Having defined the macro
commands, click on the “Write” button in the “Macro commands” tab to write the data
to the module. The macro command related data are not read / written when you click
on the button in the main menu of DLOADX program.
Groups
Fig. 9. DLOADX program: “Groups” tab.
The macro commands which are to be available to the mobile device users must be assigned
to one of the four groups. You can assign up to 16 macro commands to the groups. The
DLOADX program presents the macro command groups and the macro commands assigned
to them in the tree form.
Name – name of the macro command group (up to 8 characters). It is presented on the
macro key.
Add macro – button available after you click on a macro command group. Clicking on the
button will display a list of defined macro commands. Click on the name to add the macro
command to the group.
Remove macro – click on the button to delete the selected macro command from the group.
– click on the button to move the highlighted macro command down within the group.

SATEL ETHM-1 Plus 15
– click on the button to move the highlighted macro command up within the group.
Read – click on the button to read the macro command related data from the module.
Write – click on the button to write the macro command related data to the module.
Quit – click on the button to cancel reading or writing the macro command related data.
Reset – click on the button to delete all the defined macro commands (and restore factory
default settings).
Export to file – click on the button to export defined macro commands to a file. The file with
macro commands can be loaded into the INTEGRA CONTROL / MOBILEKPD-2 PRO
application or imported to another ETHM-1 Plus module or to a INT-KSG keypad (i.e.
macro commands can be copied between the devices).
Import from file – click on the button to import macro commands from a file.
Definitions
Fig. 10. DLOADX program: “Definitions” tab.
Macro commands can be created and configured in the “Definitions” tab. The macro
command is a sequence of actions, composed of single commands, which are to be done by
the control panel when running the macro command.
New macro – click on the button to create a new macro command.
Remove macro – click on the button to remove the selected macro command.
Name – individual macro command name (up to 32 characters).

16 ETHM-1 Plus SATEL
Code – the code which is to be used for authorization when executing commands contained
in the macro command. The code must have an appropriate authority level for execution of
such commands to be possible. The code is presented as a string of asterisks.
If the code turns out to be incorrect when running macro commands (e.g. it was
changed in the meantime), the user will be able to enter the correct code. It will be
automatically saved to the device memory (to replace the invalid code).
Authorization required – if this option is enabled, the macro command will only be run after
user authorization by means of code. The code entered in the “Code” field will be ignored.
Disabl. if armed – if this option is enabled, the macro command will not be available, if any
of the partitions managed by the virtual keypad is armed.
Autoexecute – if this option is enabled and there is only one macro command in the group,
the macro command will be run immediately on tapping the macro key (if the
AUTHORIZATION REQUIREDoption is enabled, user authorization by means of code will be
required).
Commands list – commands assigned to the currently highlighted macro command. The
and buttons allow you to change the order of commands (moving the
highlighted command up and down).
Add – click on the button to add to the list a new command, selected in the “Command” field.
Change – click on the button to save the changes to the command parameters which were
made after adding the command to the list (otherwise, the changes made will not be
saved).
Delete – click on the button to remove the highlighted command from the list.
Command – function executed by the control panel, which can be assigned to the macro
command. To display the list of all available functions, click on the button. Depending
on which function you have selected:
Arming – highlight the partitions which are to be armed (double-click on the field
designated by the partition number) and define the arming mode (next clicks on the field
designated by the partition number; the digit inside the field has the following meaning:
0 - fully armed; 1 – fully armed+bypasses; 2 – armed without interior; 3 - armed without
interior and without entry delay).
Disarming – highlight the partitions which are to be disarmed (double-click on the field
designated by the partition number).
Alarm clearing – highlight the partitions in which alarm is to be cleared (double-click on
the field designated by the partition number).
Bypass zones – highlight the zones which are to be inhibited (double-click on the field
designated by the zone number).
Unbypass zones – highlight the zones which are to be unbypassed (double-click on the
field designated by the zone number).
Outputs ON – highlight the outputs which are to be activated (double-click on the field
designated by the output number).
Outputs OFF – highlight the outputs which are to be deactivated (double-click on the field
designated by the output number).
Change outputs state – highlight the outputs whose status is to be changed (double-click
on the field designated by the output number).
KNX telegram – program the following parameters of KNX telegram:
INT-KNX module – INT-KNX module which is to send the telegram.
Group address – the group address which will be inserted in the telegram.

SATEL ETHM-1 Plus 17
Type – the telegram type.
Value – the value that will be inserted in the telegram (parameter available for some
types of the telegram).
Priority – telegram priority (if two elements of the bus start transmitting simultaneously,
the telegram with higher priority will be sent first).
Exit delay clearing (no additional parameters to configure).
Quick arm – select the arming mode which is to be activated.
The partitions must be controlled by user code.
The zones must not have the BYPASS DISABLED option enabled.
The outputs must be the 24. MONO SWITCH, 25. BI SWITCH, 105. SHUTTER UP,
106. SHUTTER DOWN or REMOTE SWITCH type (they need not be assigned to any group
of outputs).
Using the INTEGRA CONTROL / MOBILEKPD-2 PRO application, you can control the
KNX system, if the INT-KNX module is connected to the control panel.
Defining macro commands
1. Click on the “Read” button to read the macro command related data from the module.
2. Click on the “Definitions” tab.
3. Click on the “New macro” button. A new macro command will appear on the list.

18 ETHM-1 Plus SATEL
4. Enter a name for the new macro command.
5. If the macro command is to be run without entering the code by the user, enter a code
having appropriate authority level.
6. If running a macro command is to be each time preceded by user authorization, enable
the AUTHORIZATION REQUIRED option.
7. If the macro command is to be unavailable when any of the partitions managed by the
keypad is armed, enable the DISABL.IF ARMED option.
8. If the macro command is to be run immediately on tapping the macro key, enable the
AUTOEXECUTE option (in such a case, only this one macro command is to be assigned to
the group).