Satel SPL-2010 User manual

Optical-acoustic siren
SPL-2010
spl2010_en 07/23
SATEL sp. z o.o. •ul. Budowlanych 66 • 80-298 Gdańsk • POLAND
tel. [phone]
www.satel.pl
EN

IMPORTANT
The device should be installed by qualified personnel.
Prior to installation, please read carefully this manual.
Changes, modifications or repairs not authorized by the manufacturer shall void your rights
under the warranty.
SATEL aims to continually improve the quality of its products, which may result in changes in
their technical specifications and software. Current information about the changes being
introduced is available on our website.
Please visit us at:
https://support.satel.pl
The declaration of conformity may be consulted at www.satel.pl/ce
The following symbols may be used in this manual:
- note;
- caution.

CONTENTS
1. Features............................................................................................................................2
2. Description ........................................................................................................................2
Terminals..........................................................................................................................3
Pins for selecting acoustic signal......................................................................................3
Enclosure base.................................................................................................................3
3. Installation and start-up.....................................................................................................4
4. Specifications....................................................................................................................5

2 SPL-2010 SATEL
The SPL-2010 siren provides information about alarm situations by means of optical and
acoustic signaling. It is designed for outdoor installation. This manual applies to the siren with
electronics version 1.7.
1. Features
•Acoustic signaling by means of sounder.
•Three selectable tones for acoustic signaling.
•Optical signaling by means of LEDs.
•Weatherproofed electronic circuit.
•Tamper protection against enclosure opening, removing from mounting surface and
flooding of the sounder with mounting foam.
•Inner cover of galvanized metal sheet.
•High-impact polycarbonate enclosure, featuring a very high mechanical strength.
2. Description
enclosure cover.
inner metal cover.
enclosure base.
sounder.
anti-foam detector.
electronics board.
cover locking screw.

SATEL SPL-2010 3
Terminals
+SO- - input to trigger the optical signaling. The signaling will be triggered after +12 VDC
voltage is applied to terminal “+” and 0 V voltage (common ground) is applied to
terminal “-”.
+SA- - input to trigger the acoustic signaling. The signaling will be triggered after
+12 VDC voltage is applied to terminal “+” and 0 V voltage (common ground) is
applied to terminal “-”.
TMP - tamper output (NC). Connect one terminal to the control panel zone programmed
as tamper, and the other to the control panel common ground.
Pins for selecting acoustic signal
Fig. 2 shows the jumpers settings for each selectable siren tone: A–tone 1, B–tone 2, C–
tone 3.
Enclosure base
mounting holes.
anti-foam detector.
sounder.
opening for wires.

4 SPL-2010 SATEL
electronics board.
tamper element with mounting hole.
water drain holes (do not plug).
3. Installation and start-up
Power down the control panel before connecting the siren to the control panel.
The siren must be installed on the wall, high above the floor, at a hard to access location, so
as to minimize the risk of tampering. Leave a space above the siren –at least 4.5 cm
between the siren and the ceiling or other object. Otherwise, it will be impossible to replace
the cover.
1. Remove the cover locking screw.
2. Lift up the enclosure cover and remove it (Fig. 4).
3. Pull aside the mounting catches of the inner metal cover and remove it.
4. Place the enclosure base on the wall and mark the location of mounting holes (Fig. 3).
Remember to take into account the mounting hole for tamper protection.
5. Drill the holes for wall plugs (anchors).
6. Run the wires through the opening in the enclosure base (Fig. 3).
7. Use wall plugs (anchors) and screws to secure the enclosure base to the wall. Remember
about the mounting hole for tamper protection. Select appropriate wall plugs based on the
type of the mounting surface (different for concrete or brick wall, different for plaster wall,
etc.).
8. Connect the siren terminals to the control panel terminals using wires.
Some alarm control panels may require that a resistor R (approx. 1 kΩ) be connected
between the +SA- terminals in the siren (Fig. 3). Otherwise, the siren may produce
a buzzing sound when inactive (if there is no buzzing, the resistor is not required).
9. Use jumpers to select the tone (Fig. 2).
10.Replace the inner metal cover.
11.Replace the siren cover and lock it with the screw.
12.Power on the control panel.

SATEL SPL-2010 5
After the siren is mounted, it is recommended to seal the mounting holes and cable
entry hole with silicone paste.
4. Specifications
Supply voltage.................................................................................................... 12 VDC
±
15%
Maximum current consumption:
optical signaling...........................................................................................................35 mA
acoustic signaling......................................................................................................250 mA
optical and acoustic signaling....................................................................................300 mA
Sound pressure level (at 1 m distance) .................................................................up to 120 dB
Environmental class according to EN 50130-5.......................................................................III

6 SPL-2010 SATEL
Operating temperature range...............................................................................-35°C...+55°C
Maximum humidity..........................................................................................................93
±
3%
Dimensions................................................................................................. 298 x 197 x 90 mm
Weight............................................................................................................................1,22 kg