Satel CSP-204 Installation manual

Fire Alarm Control Panel
CSP-204
CSP-208
CSP-104
CSP-108
Operation manual
Firmware version 1.1 csp-x_o_en 06/15
SATEL sp. z o.o.
ul. Budowlanych 66
80-298 Gdańsk
POLAND
tel. [phone]
www.satel.eu

CONTENTS
1. Introduction.....................................................................................................................2
2. Front panel description..................................................................................................3
2.1 LED indicators ...........................................................................................................6
2.2 Buttons ......................................................................................................................8
3. Conditions signaled by the control panel / repeater panel.......................................10
4. Operation.......................................................................................................................11
4.1 Access levels........................................................................................................... 11
4.1.1 Level 1 – all users ........................................................................................................ 11
4.1.2 Level 2 – authorized users ........................................................................................... 11
4.2 Access level 1 operation..........................................................................................12
4.2.1 Silencing the acoustic signaling of control panel / repeater panel................................ 12
4.2.2 Testing the signaling components of control panel / repeater panel ............................ 12
4.2.3 Checking availability of the access level 2 operation on the other panel ..................... 12
4.2.4 Using the user menu [CSP-204 / CSP-208 / PSP-204 / PSP-208] .............................. 12
4.3 Access level 2 operation..........................................................................................13
4.3.1 Enabling / disabling the two-stage alarm mode............................................................ 13
4.3.2 Procedure in the case of alarm signaling ..................................................................... 14
4.3.3 Deactivating / activating the sounders.......................................................................... 14
4.3.4 Procedure in the case of fault signaling........................................................................ 14
4.3.5 Disablement ................................................................................................................. 14
4.3.6 Testing the zones ......................................................................................................... 15
4.3.7 Testing the routing outputs and sounders .................................................................... 15
4.3.8 Using the user menu [CSP-204 / CSP-208 / PSP-204 / PSP-208] .............................. 15
5. Using the virtual panel.................................................................................................16

2 CSP-204 ●CSP-208 ●CSP-104 ●CSP-108 SATEL
1. Introduction
This manual describes how to operate the following fire alarm control panels:
CSP-104 - 4 zone conventional fire alarm control panel,
CSP-108 - 8 zone conventional fire alarm control panel,
CSP-204 - 4 zone conventional fire alarm control panel with LCD display,
CSP-208 - 8 zone conventional fire alarm control panel with LCD display.
The manual also covers remote operation of the fire alarm control panels by means of
repeater panels and explains how to use the virtual panel.
Please read this manual carefully before use.
Fig. 1. Typical components included in the fire alarm system.

SATEL Operation manual 3
2. Front panel description
The following items are placed on the front panel of the control panel / repeater panel:
LED indicators;
control buttons;
insert with zone descriptions to facilitate identification of the alarm source;
LCD display to make easier transmission of information (only CSP-204, PSP-204,
CSP-208 and PSP-208);
key switch to enable changing the access level.
Fig. 2. Front panel of the CSP-208 control panel.
Fig. 3. Front panel of the PSP-208 repeater panel.

4 CSP-204 ●CSP-208 ●CSP-104 ●CSP-108 SATEL
Fig. 4. Front panel of the CSP-204 control panel.
Fig. 5. Front panel of the PSP-204 repeater panel.

SATEL Operation manual 5
Fig. 6. Front panel of the CSP-108 control panel.
Fig. 7. Front panel of the PSP-108 repeater panel.

6 CSP-204 ●CSP-208 ●CSP-104 ●CSP-108 SATEL
Fig. 8. Front panel of the CSP-104 control panel.
Fig. 9. Front panel of the PSP-104 repeater panel.
2.1 LED indicators
LED Description Color Indications
fault yellow ON – fault
blinking – fault memory
test yellow
blinking – test function is activated
ON – test of zones, sounders, fire alarm routing
output or fault warning routing output is running
disabled yellow
blinking – disablement function is activated
ON – zones, sounders, fire alarm routing output or
fault warning routing output are disabled

SATEL Operation manual 7
zone 1
zone 2
zone 3
zone 4
zone 5
zone 6
zone 7
zone 8
yellow blinking – zone fault (short-circuit or break)
ON – zone is disabled or is being tested
fire routing yellow blinking – output fault (short-circuit or break)
ON – output is disabled or is being tested
fault routing yellow blinking – output fault (short-circuit or break)
ON – output is disabled or is being tested
sounders yellow blinking – sounder fault (short-circuit or break)
ON – sounders are disabled or are being tested
power yellow
blinking – power supply failure (loss of 230 V AC
mains, missing battery, low battery, high battery
resistance)
auxiliary devices yellow
blinking – programmable input fault (short-circuit
or break), fault signaled by a device connected to
programmable input, power output fault
(overload), repeater panel or CSP-ETH module
not present, repeater panel fault
system yellow
blinking – control panel hardware fault,
microprocessor-based system fault, corrupted
data in control panel memory, or alarm log
overflow
earth fault yellow blinking – earth fault in one of the circuits of fire
alarm system
fault routing yellow
blinking – fault warning routing output is active
(no confirmation of transmission)
ON – fault warning routing output is active and
transmission is confirmed
fire routing red
blinking – fire alarm routing output is active (no
confirmation of transmission)
ON – fire alarm routing output is active and
transmission is confirmed

8 CSP-204 ●CSP-208 ●CSP-104 ●CSP-108 SATEL
power green
ON – control panel is supplied from 230 V AC
mains
blinking – control panel is supplied from a battery
(no 230 V AC supply)
delays yellow
ON – two-stage alarm mode is enabled (second
stage alarm is delayed)
fire red
blinking – fire alarm
ON – fire alarm acknowledged by the operator
fire in zone 1
fire in zone 2
fire in zone 3
fire in zone 4
fire in zone 5
fire in zone 6
fire in zone 7
fire in zone 8
red
slow blinking – pre-alarm
fast blinking – first alarm
ON – next alarm
Only the control panel
service blue
slow blinking – access level 2
fast blinking – waiting for code entry after the
key is pressed
ON – access level 3 (programming)
Only the repeater panel
info blue
slow blinking – access level 2
ON – repeater panel cannot be operated
2.2 Buttons
Button Access
level Function
1 - starts the test of LED indicators and built-in sounder of control
panel / repeater panel
2 - starts the function of testing zones, sounders, fire alarm routing
output or fault warning routing output
2 - starts the function of disabling zones, sounders, fire alarm
routing output or fault warning routing output

SATEL Operation manual 9
2
- after pressing the button – disables / enables the zone
- after pressing the button – starts / stops the zone test
- after pressing the button – the buttons 1-4 allow to enter the
level 3 access code (programming)
2
- after pressing the button – disables / enables the fire alarm
routing output
- after pressing the button – starts a test of the fire alarm
routing output
2
- after pressing the button – disables / enables the fault
warning routing output
- after pressing the button – starts test of the fault warning
routing output
2
- deactivates / activates sounders during a fire alarm
- after pressing the button – disables / enables the sounders
- after pressing the button – starts a test of the sounders
1 or 2
- acknowledges the alarm or fault warning and silences the
acoustic signaling in control panel and repeater panel
- resets the fault memory
2 - resets the fire alarm
- resets the fault
2 - activates / deactivates two-stage alarm mode (second stage
alarm delay)
Only the control panel
1 - allows to check whether level 2 operation is available on the
repeater panel
2 - allows to gain level 3 access (control panel programming)
Only the repeater panel
1 - allows to check whether level 2 operation is available on the
control panel's front panel