Satel ASP-105 User manual

®
WIRELESS OUTDOOR SIREN
ASP-105
asp105_e 08/05
The ASP-105 wireless outdoor siren is designed for operation as part of the ABAX
two-way wireless system.
The optical and acoustic signaling are independently triggered by radio. A xenon lamp
(flash) is the source of light signal, while the sound signal is generated by means of
a piezoelectric transducer.
The ASP-105 outdoor siren is supplied with +12V (±15%) direct voltage. An
emergency power supply is the 6V 1.2Ah battery.
1. DESCRIPTION OF ELECTRONICS BOARD
Electronic circuit of the outdoor siren is made with the use of SMD technology and
impregnated against adverse effect of weather, which ensures a high reliability of the
device.
A tamper contact, which reacts to opening or pull-off of the housing from the surface,
is connected to the TMP terminals. The terminals +12V and COM are used to connect
the outer power supply.
The 3.15A fuse protects the battery power supply circuit.
The LED indicator is "on" in the TEST MODE only (see the ACU-100 controller manual)
to signal communication with the controller.
antenna red black
to battery to piezoelectric
transducer
LED indicator
fuse 3.15A
xenon lamp
Fig. 1. Outdoor siren electronics board

SATEL ASP-105
2
Placed on the electronics board is a label with 7-digit serial number, which must be
indicated when registering the outdoor siren in the system.
2. INSTALLATION
Prior to permanent mounting of the outdoor siren, you should check the level of signal
received from the siren by the ACU-100 controller and, if necessary, change place of
the installation so as to ensure optimal positioning in terms of communication.
The ASP-105 outdoor siren should be mounted on flat surface, at a high and hard-to-
access place, so as to minimize the risk of tamper. The device is to be attached to the
surface by using screws and expansion bolts.
In order to permanently install the wireless outdoor siren:
1. Remove the two screws locking the device cover.
2. Lift the cover by an angle of approx. 60° and remove it.
Caution ! The converter which supplies the optical signaling system generates high voltages
which may cause an electric shock. Therefore, observe safety precautions: carry
out the installation only with the battery disconnected, and connect the +12V
cable last.
3. Pass the 12V DC outer supply cable through the hole in the housing.
Fig. 2. View of outdoor siren housing
4. Using screws, secure the rear housing panel to the surface. It is advisable to keep
a clearance of minimum 2.5cm between the upper edge of the outdoor siren and
the ceiling or any element that may be situated above the device. Otherwise,
replacement of the cover may prove impossible.
5. Using a screw, secure the tamper element to the surface.
6. Using silicone, seal the mounting holes and the cable inlet opening.
cover locking screws
tamper contact
(to be screwed to surface)
screw
holes
cable inlet opening

ASP-105 ABAX 3
7. Connect the battery.
Note: The tamper alarm signaling will be blocked after activation of the service mode in case
of operation with INTEGRA series control panels, or activation of the TEST MODE in
any other configuration, as well as for 40 seconds after power-up of the siren.
8. Screw the outer supply cable to the terminals on the electronics board. The cable
should not be laid up in the close vicinity of the siren antenna, since it may cause
radio communication interference.
9. Replace the device cover and lock it with screws.
For information on registration and installation of the outdoor siren in the
wireless system - see the ACU-100 Controller User Manual.
3. TECHNICAL DATA
Operating frequency band..........................................................868.0MHz ÷ 868.6MHz
Nominal supply voltage ............................................................................12V DC ±15%
Current consumption (average):
- standby mode...............................................................................................30mA
- standby mode + battery charging...............................................................150mA
- optical signaling..........................................................................................165mA
- acoustic signaling .......................................................................................450mA
Inner battery...................................................................................................... 6V/1.2Ah
Inner battery protection................................................................................fuse T 3.15A
Operating temperature range....................................................................-20°C...+55°C
Housing dimensions .............................................................................. 148x254x64mm

DECLARATION OF CONFORMITY
Product:
ASP-105 - Outdoor Siren for ABAX System
Manufacturer: SATEL spółka z o.o.
ul. Schuberta 79
80-172 Gdańsk, POLAND
tel. [phone]
fax. [phone]
Product description:Wireless outdoor siren with battery backup, designed for interaction with the
controller of the ABAX wireless system, operating in the 868.0MHz – 868.6MHz frequency range,
supplied from a 3V lithium cell. The device is intended to be used in burglary and panic alarm
systems.
This product conforms to the following EU Directives:
R&TTE 1999/5/EC
This product meets requirements of the harmonized standards:
R&TTE: ETSI EN 300 220-1: v.1.3.1; ETSI EN 300 220-3: v.1.1.1;
EMC: ETSI EN 301 489-1: v.1.5.1.; EN 301 489-3: v.1.4.1
Safety: EN60950-1:2001
Notified body taking part in conformity evaluation:
Identification No.: 1471
Gdańsk, Poland 2005-07-15 Head of Test Laboratory:
MichałKonarski
The latest EC declaration of conformity and product approval certificates are available for
downloading on our website www.satel.pl
SATEL sp. z o.o.
ul. Schuberta 79
80-172 Gdańsk
POLAND
tel. + 48 58 320 94 00
[email protected]
www.satel.pl