SawStop JOBSITE SAW PRO User manual

CONGRATULATIONS!
YOUR SAW IS NOW ASSEMBLED
x2 x2
x4
x4
x2
HARDWARE
CART HANDLES
WHEELS
UNBOXING AND ASSEMBLY
LET’S GET STARTED
HAVE QUESTIONS?
Give Us a Call
or Email Us
503-563-5822
[email protected]
P JSSP 19 0001 00
Our technical support team is standing by, M-F, 7am-5pm PST
to help with whatever you need.
CONGRATULATIONS!
WASHER M10 LOCKNUT
M10 BOLT
M6 LOCKNUT
M6 BOLT
8A
9A
8B
9B
8C
9
8
7
54
32 1
6
Check to make sure you have all the parts. If not, call
us at 503-595-2665.
Remove the large packing tray and set aside. Cut both vertical edges of the box on the end near the
wheels and fold down. Remove the small packing tray by
sliding out from the cart and set aside.
Once the wheels are mounted, tip the saw and cart to
the upright position.
Mount the wheels to the cart with the provided bolts,
washers and nuts.
Lift and place the saw so it overhangs the bottom packing
tray by about 6 inches. This provides room to attach the
wheels to the frame.
Slide the handle marked “L” into the tube nearest the front of
the saw and bolt in place. Tighten the bolt enough to compress
the tubes so the handle does not jiggle. Install the handle
marked “R” in the same way in the other tube.
Do not attempt to elevate the blade until steps 8 and 9 are complete. Roll the saw off the cardboard. Tip the saw down to rest on the
cart handles. Grasp and squeeze the backplate against the elevation handwheel (8A) and swing the handwheel to the right (8B) until
the red pointer is over the 45 degree mark (8C). Release the backplate to lock the tilt at 45 degrees.
At the back of the saw, reach into the opening and remove a piece of red tape that holds a metal shipping pin in
place (9A). Then pull the metal shipping pin completely out of the saw (9B). This pin holds the elevation mechanism in
place during shipping and can now be discarded.

Open the clamp by reaching into the
opening and ipping the red handle up.
Always switch the power off and
unplug the power cord before
changing the riving knife or blade
guard.
Place the riving knife or blade guard into
the clamp.
Press the front of the table insert down to
lock.
Squeeze the latch on the table insert (1A),
and then lift the insert up and toward the
front of the saw (1B).
Slide the riving knife or blade guard out of
the clamp.
Flip the red handle down to close the clamp.
With the rear of the table insert tilting
downward, slide the table insert into the
table opening so that the screws on the
bottom of the table insert slide beneath
the screws in the table.
Wait while the saw powers up. A
solid green light appears and the red
status light ashes slowly until the
saw is ready.
Once the red light stops ashing
and is off, the saw is ready to use. If
the red light stays on, refer to the
owner’s manual.
Pull the paddle out to spin
the blade.
With the paddle pushed in,
ip the power switch to the
ON position.
The green status light ashes fast
while the spins down, until the blade
comes to a complete stop.
When the green light is solid, the saw
is ready to shut off.
After you nish all your cuts,
ip the power switch to the
off position.
Push the paddle in to turn
the motor off.
The rip fence is stored in brackets on the right side of the saw, beneath
the table extension. Lift the gray latch to remove the fence.
Slide the fence out of the brackets and lay it on the
table. Make sure the red lever is unlocked.
Align the fence on the front rail and slide it to the desired cutting
position. Press the red lever to lock the fence in place.
Flip the table extension handle up. Slide the table extension to its furthest open position.
Slide out the storage drawer.
Lift the lid to locate the saw accessories and
user guide.
Grasp the handles and step on the locking lever. Pull the handles downward. The wheels will
swing down and to the rear. The cart will lock in
place once the saw is in the full upright position.
To collapse the cart, grasp the handles, step on the
locking lever, and then raise the handles. Press the
wheels forward until they lock in place.
1 2
7
3
6
2 4
3
24
3
1
1
1A
1B
2
1
23
2
4 5
3
1
3
1
Switch Power On
Switch Power Off
TURN THE SAW ON AND OFF
INSTALL THE RIVING KNIFE OR BLADE GUARD
LOCATE AND INSTALL THE RIP FENCE
LOCATE THE ACCESSORIES
USE THE MOBILE CART