Saxby Lighting 107632 User manual

www.saxbylighting.com
Instruction manual
107632, 107633, 107634, 107635, 107636, 107637, 107638
Guard Floodlight
We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish.
For your safety, always switch off the power supply before cleaning.
Care and Safety
Technical data
220-240 V~, 50 Hz
Supply
Voltage:
Bulb
Type:
107632: 10W LED module (SMD), 4000K
107633: 20W LED module (SMD), 4000K
107634: 30W LED module (SMD), 4000K
107635: 50W LED module (SMD), 4000K
107636: 100W LED module (SMD), 4000K
107637: 150W LED module (SMD), 4000K
107638: 200W LED module (SMD), 4000K
This is a Class 1 product and must be earthed.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities
exist. Check with your Local Authority or local store for recycling advice.
This product is rated at IP65.
IP 65
This product is rated at IK08.
Caution! Risk of electric shock!
This LED's are protected by the glass shade. The shade part must be replaced immediately should it
become cracked or damaged. This fitting must not be used without the glass shade in place.
Replace Cracked Shade
For further information, please visit https://www.lighting-info.co.uk/107632
V3 12/08/2023
EU Manufacturer: Brilliant AG,
Brilliantstrasse 1, D-27442 Gnarrenburg
UK Manufacturer: BH17 7BY
Conformity with all relevant EC Directive requirements.
Conformity with all relevant UKCA Directive requirements.
IK08
This product contains a light source of energy efficiency class F.
Non-replaceable control gear
Non-replaceable light source

Warning
This is a Class 1 product and must be earthed.
Please read these instructions carefully before commencing any work
This unit must be fitted by a competent and qualified electrician.
Install in accordance with the IEE Wiring regulations and current Building Regulations.
Check the pack and make sure you have all the parts listed.
To prevent electrocution switch off at the mains supply before installing or maintaining this fitting. Ensure other persons cannot
restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified electrician.
If replacing an existing fitting, make a careful note of the connections.
The entire unit gets hot whilst on for a period of time.
This product is not suitable for location in or near a marine environment.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with
your local authority or retailer for recycling advice.
Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory
operation of this product. Please retain these instructions for future reference.
Layout
Plan the desired layout of these fittings carefully, ensuring the cables will reach the distances between each light fitting.
Avoid locating any cables in positions that would cause a hazard. Position cables and outdoor rated junction boxes
(not supplied) away from areas where they may be at risk from being cut, trapped or damaged.
This product is supplied with 0.8 metres of H05RN-F outdoor grade rubber sheathed cable ready for connection to an approved,
outdoor rated terminal block which is not supplied and must be obtained.
The mains supply cable must have a minimum cross section area of 1.0mm2.
The external flexible cable or cord of this luminaire cannot be replaced. If the cord is damaged, the luminaire must be destroyed.
Cables must be protected using suitable conduit or plastic trunking.
This is a floodlight product, and therefore should be positioned where it will not cause a glare hazard.
Installation
Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully
note the position of each set of wires.
Note that the switch is turned off before installation.
Do not mount ceiling/wall fittings onto damp surfaces such as newly painted or plastered areas as this may cause
discolouration of the finish.
Lights can install on the ground, wall or ceilling according to actual situation with suitable expansion bolt (not supplied) fixing
according to light's bracket.
You have correctly identified the wires.
The connections are tight.
No loose strands have been left out of the connection block.
Check that...
• Hold the product in position and mark the location of the fixing holes. The bracket can be removed from the fitting for
ease of installation.
• Fix the bracket to the wall using the expansion bolt (not supplied). Take care to avoid damaging any concealed wiring and
pipes. The correct fixings ahould be used for brick or cavity walls.
• Using the Allen key (not supplied), loosen the bolts on the both side, and adjust the fitting to the desired angel.
• Wire as detailed wiring.
• Turn on your power switch. your light is ready for use.
Having correctly identified the wiring from your existing light fitting, pull the mains wire through the hole and connect to an
approved outdoor rated terminal block(not supplied) in the following way:
Wiring
SUPPLY LIGHT FITTING
BLUE (N)
NEUTRAL
EARTH
SWITCHED LIVE BROWN (L)
GREEN / YELLOW
See wiring diagram
Adjust the
desired angle
(both side)
Outdoor rated terminal block
(not supplied)