Saxby Lighting Laryn 5278J Manual

• Thissystem contains non-replaceable parts and
cannot be serviced. If damage occurs the part should
be scrapped.
Instruction leaflet
Laryn PIR Flood Light
5278J, 7172J
www.saxbylighting.com
For your safety, always switch off the supply before cleaning.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities
exist. Check with your Local Authority or retailer for recycling advice.
Recycling advice
Safety information
Saxby Lighting Ltd. BH23 3PE
We recommend cleaning with a soft dry cloth.
Do not use solvents or abrasive cleaners as these could
damage the finish.
The LED's are protected by a lens. This part must be replaced immediately should the lens become
cracked or damaged. This fitting must not be used without the lens in place.
Fitting/replacing bulbs
27012021
UK Manufacturer:
BH17 7BY
EU Manufacturer:
Brilliant AG, 27442, Germany

Thankyouforpurchasingthislightfitting.Pleasereadtheinstructionscarefullybeforeusetoensuresafeand
satisfactoryoperationofthisproduct.Pleaseretaintheseinstructionsforfuturereference.
Warning
Theunitcannotbedimmed.
Thissystemcontainsnon-replaceablepartsand
cannotbeserviced.Ifdamageoccursthepartshould
bescrapped.
Wasteelectricalproductsshouldnotbedisposedof
withhouseholdwaste.Pleaserecyclewherefacilities
exist.Checkwithyourlocalauthorityorretailerfor
recyclingadvice.
ThisproductisratedatIP44.
Thisproductisnotsuitableforlocationinorneara
marineenvironment.
Battery Care:-
- Donotrechargenon-rechargeablebatteries.
-Donotmixoldandnewbatteriesorbatteriesof
differenttypes/brands.
-Donotuserechargeablebatteries.Alwaysremove
exhaustedbatteriesfromtheproduct.
-Alwaysinsertbatterieswiththecorrectpolarity.
-Donotshortthesupplyterminals.
-Thisproductissuitableforusebyadultsonly.
Specification
Voltage: 4.5V
Lamp: 5278J:1x2WLEDmodule(SMD5630),7172J:2x2WLEDmodule(SMD5630)
IPrating: 44
BatteryType: 3x1.5VLR14‘C’(notsupplied).Usinggoodqualitybatteries,theexpectedlengthoftime5278J 
 willoperateis9hours,and4.5hoursfor7172J.
Layout
• Avoidmountingonsurfacessubjecttovibration,as
thismayaffectthePIRsensor.
• Toavoiddamagetotheunit,donotaimthesensor
towardsthesunorareasofstrongelectro-magnetic
disturbances.
• Toavoidnuisancetriggering,thesensorshouldbe
aimedawayfromheatsources,suchasBBQ’s,
Air-Conditioners,otheroutsidelighting,movingcars
andflueventsorreflectivesurfacessuchassmooth
whitewallsorswimmingpools.
• Whenselectinglocation,itisadvisabletonotethat
movementacrossthesensorsfieldismoreeffective
thantowards/awayfromit..
• Decideontheoptimumlocationfortheproduct.
Ensurethewalliscapableofholdingtheweightof
theproduct.
• Placethefloodlightinanuprightposition.
• Removethescrewfromthebaseoftheproductand
setasideforrefittinglater.
• Todetachthewallbackfromtheproduct,press
downthebutton(ontopofthebatterybox)withone
handandpulltheribbontabwiththeotherhand.
• Usingthewallbackasatemplate,markanddrillthe
positionofthefixingholes.
• Fixthewallbacktothewallusingthescrewsand
plugs.Takecaretoavoiddamaginganyconcealed
wiringandpipes.Thecorrectfixingsshouldbeused
forbrickorcavitywalls.
• Fitthebatteries,ensuringtheBatteryCarewarnings
onthepreviouspageareheeded.
• Pushthebuttonontopofthewallbackdownwith
onehandandpushtheproductontothewallback.It
willclickinplace.Refitthescrewtothebaseofthe
producttosecureinplace.
• Switchontheproductusingthetoggleswitchand
adjustthePIRsensorasdetailedbelow.Pleasenote
thesensorrotatesforeasyaccesstothecontrols.
Linethewhitedotsupatthefrontoftheproductto
ensurethecorrectorientation.
• Yourlightisnowreadyforuse.
Installation
PIR Adjustment
• Theunit mustbe installedin avertical position,and
fittedbetween1.8and2.5mabovetheground.
• ThePIRsensorcanbeadjusted,allowingthedetection
distance to be altered to suit the location. The
detection angle is set at 130 degrees. The duration
thatthelampstaysoncanbealteredfrom5seconds
- 1 minute. The detection distance "SENS" can be
adjustedfrom1.5mto8mUseasmallscrewdriverto
adjustthe‘TIME’and‘SENS’screws.Whenadjusting
thesensitivity(detectiondistance)indaylightitwillbe
necessarytocoverthesensortosimulatenighttime.