Saxby Lighting 78963 Manual

Surge (Floodlight) PIR
78963, 78965, 78967, 78969, 78970
Instruction leaflet
Care and Safety
•We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage
the finish.
•For your safety, always switch off the supply before cleaning. Iss .2 22/11/2018
WWW.saxbylighting.com Saxby lighting. BH23 3PE
PIR Specification
• 78963, 78965, 78967 and 78969 are fitted with PIR motion sensor. The specification is as follows:
• Turn the time dial to minimum(-), the sensitivity dial to maximum(+) and the lux dial to maximum (sun).
• To override the PIR, switch off the power to the floodlight then re-apply the power within 3 seconds.
• To return to automatic mode, switch off the power to the floodlight then re-apply the power after 10 seconds.
Dials shown in maximum positions
• Switch on the power supply electricity and but not activate the PIR sensor.
• Wait approximately 15 seconds while the floodlight initiates
by turning on and off.
• After the floodlight deactivates, it can be activated with motion
in fornt of the PIR sensor.
• Adjust the time dial for the desired duration on and the sensitivity
dial to the desired distance.
• Initial setup and testing in daylight is now complete.
If in doubt, contact a qualified electircian.
• Turn the lux dial to minimum(moon). When the ambient light
level is at the desired level (to turn on the floodlight),
rotate the lux dial until the floodlight turns on.
Please read in full before installation and keep for future reference take care not to over rotate the dials.
They do not rotate through 360 for testing in daylight.
Installation Instructions
Manual Override Instructions
Optimum mounting height: 1m-3m.
Timer Function (TIME): 10±5 seconds to 8±2 minutes
Detection angle: 120˚
Detection distance (adjustable) : 8±2m( <24 )℃
Lux Range (LUX): 2-2000 lux
Working TemperaturePower:-10℃— +45℃
•You have correctly
identified the wires.
•The connections are tight.
•No loose strands have
been left out of the terminals.
Terminal block not included. Installation may require advice from a qualified person. Connect to an approved
outdoor rated terminal block, observing the wiring diagram here:
SUPPLY
NEUTRAL
EARTH
SWITCHED LIVE
BLUE (N)
GREEN/YELLOW
BROWN (L)
LIGHT FITTING
Wiring
Check that...

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory
operation of this product. Please retain these instructions for future reference.
Warning
Technical data
Please read these instructions carefully before
commencing any work.
This light fitting should be connected to a circuit
with a 30mA RCD fitted.
The external flexible cable or cord of this luminaire
This product is not suitable for location in or near
a marine environment.
The entire unit gets hot whilst on for a period of time.
cannot be replaced; if the cord is damaged,
the luminaire must be destroyed.
This product is supplied with 1 metres of
H05RN-F outdoor grade rubber sheathed cable -
ready for connection to an approved, outdoor
rated terminal block which is not supplied and
must be obtained.
This is a floodlight product, and therefore should be
positioned where it will not cause a glare hazard.
Terminal block not included. Installation may
require advice from a qualified person.
This unit must be fitted by a competent and qualified
electrician.
Check the pack and make sure you have all of the
parts listed.
To prevent electrocution switch off at mains supply
before installing or maintaining this fitting.
Ensure other persons cannot restore the electrical
supply without your knowledge.
Install in accordance with IEE Wiring regulations and
current Building Regulations.
Supply
Bulb Type:
Voltage: 240V~, 50 Hz
78963 : 10W SMD 2835 4000K
78969 : 50W SMD 2835 4000K
78965 : 20W SMD 2835 4000K
78967 : 30W SMD 2835 4000K
The light source of this luminaire is not replaceable; when the light source reaches its end
of life the whole luminaire shall be replaced.
Conformity with all relevant EC Directive requirements.
Waste electrical products should not be disposed of with household waste.
Class I product, must be connected to earth.
Please recycle where facilities exist.Check with your Local Authority or
local store for recycling advice.
This product is not suitable for dimming.
78963 / 78965 / 78967 / 78969
Installation
Existing fittings must be completely removed before installation of a new product. Before removing the
existing fitting, carefully note the position of each set of wires.
• Note that the power needs to be isolated/switched off at the fuse board.
• Decide on the optimum location for the product. For PIR versions, the optimum height is between 1m-3m.
• Lights can install on the ground、wall or brackets according to actual situation such as installation on the
brackets with hexagonal head screw fixed.And dig the hole on ground or wall with suitable expansion
bolt（not provide) fixing according to light's bracket if install on the ground or wall.
• Cables must be protected using suitable conduit or plastic trunking.
• Plan the desired layout of this fitting carefully, ensuring the cables will reach the distance between the
junction box and the light fitting.
• Avoid locating any cables in positions that would cause a hazard. Position cables and outdoor rated junction
boxes (not supplied) away from areas where they may be at risk from being cut, trapped or damaged.
IP44
If replacing an existing fitting, make a careful note
of the connections.
Installed on the ground
Installed on the Wall
• Drill and plug the wall at the marked positions.
• Drill and plug the wall at the marked positions.
• Use screw fix the bracket to the accessory "78970".
• Mount the product on the bracket and adjust
the desired angle
• Fix the bracket to the wall using the screws and plugs (not provided). Take care to avoid damaging any
concealed wiring and pipes. The correct fixings should be used for brick or cavity walls.
• Hold the product in position and mark the location of the fixing holes. A minimum of two fixing points must
be used. Ensure the wall is capable of holding the weight of the product. The bracket can be removed from
the fitting for ease of installation
• Hold the product in position and mark the location of the
fixing holes. The bracket can be removed from the
fitting for ease of installation.
• Wire as detailed wiring.
• Wire as detailed wiring.
• Refit the cover on the IP terminal block. Ensure that the seals are correctly located, and refit the screws.
• Refit the cover on the IP terminal block. Ensure that the
seals are correctly located, and refit the screws.
• Using the allen key (not supplied), loosen the bolts on the side, and adjust the fitting to the desired position.
Ensure that the cable is not snagged. Re-tighten the bolts.
78970
2
1
Fig 1.