SC&T IP09CK User manual

Smart Cabling & Transmission Corp.
V1.0_
191128M
IP/ PoE Extender
User Manual
Model : IP09CK
Ethernet over Coaxial Extender

1
User Manual
IP09CK
Introduction
IP09C is an IP extender that can use a single coaxial cable to send TCP/IP signal to a remote IP-enabled
device, with transmission distance up to 800M and bandwidth up to 100Mbps. Furthermore, since IP09C
can send IP signal over a coaxial cable, you can change your old analog cameras to IP ones without
replacing existing cables, which saves a plenty of labor and cost.
Features
Sends IP signal over coaxial cable.
Signal extension up to 800M over a RG59/6U coaxial cable
Bandwidth up to 70Mbps.
Able to send multiple IP signals over single Ethernet cable
Transmission Distance Chart
The transmission distance test report below is by means of using the COMMSCOPE 57535-2 (CAT5e
24AWG) cables and 75ΩRG59 or RG6U coaxial cables.
Port / Cable
Mode and Data Rate
Distance
RJ45 - CAT.5e
100BASE-TX with EEE 100Mbps
100M
RJ45 - CAT.5e
100BASE-TX 100Mbps
130M
RJ45 - CAT.5e
100BASE-T1 100Mbps
300M
RJ45 - CAT.5e
Long Reach 100Mbps
500M
RJ45 - CAT.5e
10BASE-T with EEE 10Mbps
100M
RJ45 - CAT.5e
10BASE-T 10Mbps
250M
RJ45 - CAT.5e
Long Reach 10Mbps
800M
BNC - RG59 (75-3)
100Mbps
300M
BNC - RG6U (75-5)
100Mbps
500M
BNC - RG59 (75-3)
10Mbps
800M
BNC - RG6U (75-5)
10Mbps
1000M

2
User Manual
IP09CK
I
Installation view
1) Point to Point Transmission
(2) Extra Long Extension by connecting with IP09
(3)Long Distance for Multiple cameras transmission

3
User Manual
IP09CK
Panel Review
No.
Interface
Function
1
RJ45 Connector
Port 1；To connect networking devices or another IP09
(Refer to Description 1,2,3)
2
BNC Connector
Port 2；To connect the other endpoint of IP09C
(Refer to Description 1,2)
3
RJ45 LED
To indicate the network connection status
(Refer to Description 4)
4
Power Jack
To connect DC12V 0.5A adapter
5
Power LED Indication
To indicate the power status (Refer to Description 5)
6
Status Indication
□
1Status : Port 1 mode indication (Refer to Description 6)
□
2Status : Port 2 mode indication (Refer to Description 6)
7
DIP Switch
To select the desired mode (Refer to Description 7)
Description
1Link speed of port 1 and 2 must be sync, or they are not able to activate network connection.
2Once the port 1 and 2 remain unlinked, the IP09C will automatically turn to Power Saving
mode.

4
User Manual
IP09CK
I
3RJ45 Pinout
4RJ45 LED
Date Rate
Light On
Light Off
Light Blinking
100Mbs
Enable
Disable
Data Transferring
10Mbps
Enable
Disable
Data Transferring
5 Power LED Indication
Green On
Green Off
Light Breathing
Power On
Power Off
Power Saving
6Status Indication:
□
1Status:
Blue On
Blue Off
Light Blinking
Blink twice
Long Reach
Ethernet
100BaseT-T1
Hardware Failure
□
2Status
Blue On
Blue Off
Light Blinking
10Mbps
Disable
100Mbps
7Dip Switch Setting
7.1 Auto Mode / Default (Highly Recommended)
Dip switch 1-2-3-4 all up (OFF)
Auto Mode to enable auto negotiation which automatically set up the link speed and
transmssion protocol.
(PIN TIA/EIA-568B)
PIN
Wire Color
1
Orange-white
2
Orange
3
Green-white
4
Blue
5
Blue-white
6
Green
7
Brown-white
8
Brown

5
User Manual
IP09CK
7.2 Auto+EEE Mode
Dip switch 1 down (ON), 2-3-4 up (OFF)
Auto+EEE mode supports Energy-Efficient Ethernet based on Auto Mode.
7.3 Advanced Mode
Please refer to the chart below to manually set up the Link Speed, and Modes
No.
Mode
↑OFF
↓ON
1
LINK SPEED
10Mbps
100Mbps
2
ETHERNET
Disable
Enable
3
100BASE-T1
Disable
Enable
4
LONG REACH
Disable
Enable
※Link speed of 10Mbps is not supported on 100BASE-T1 mode
Auto-Negotiation Priority
Priority
Mode
1 (Highest)
Long Distance 100Mbps
2
100BASE-T1
3
Long Distance 10Mbps
4
100BASE-TX Full Duplex
5
100BASE-TX Half Duplex
6
10BASE-T Full Duplex
7 (Lowest)
10BASE-T Half Duplex
IP09CK Package Include
2 x IP09C
2 x DC12V 500mA Power Adapter
4 x Screw
4 x Screw Plug

6
User Manual
IP09CK
I
Specification
ITEM NO.
IP09C
Support
Compliance
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE 802.3bw 100BASE-T1 Ethernet
IEEE 802.3 Nway Auto-Negotiation
IEEE 802.3x Full Duplex Operation And Flow Control
IEEE 802.3az Energy Efficient Ethernet
Network Bandwidth
10/ 100Mbps
Transmission Distance
1000M at 10Mbps, 500M at 100Mbps
Ports & Interfaces
Ethernet Interface
1 x RJ45
Link Interface
1 x BNC
Power Interface
2 x (2mm) DC Jack
Power
Power Supply
DC 12V 500mA Regulated
Power Consumption
1W 90mA
Ambient Temperature
Operation
0 to 55℃
Storage
-20 to 85℃
Humidity
Up to 95%
Physical Characteristics
Dimensions
49 x 98.7 x 25mm
Weight
130g