Schick Dental C1-Master User manual

English
Operating Instructions
1
C1-Master
E

We are pleased that you decided
to buy a highly developed piece of
equipment from SCHICK and
would like to wish you every
success when working with your
new C1 Master motor unit.
We wrote these operating
instructions to enable you to get
accustomed to your new piece of
equipment and to provide you
with the correct operating and
maintenance instructions.
Index
1. Safety information
Caution!
2. Range of applications
3. Summary C1-Master units
4. List of contents - accessoires
5. Setting up / operating the unit
6. Digital display
7. Exchanging the rotary instruments
8. Replacing the chuck
9. Maintenance and care
10. Possible faults
11. Technical Data
12. Declaration of conformity
1. Safety information
1.1 Ascertain that your mains supply coincides
with the data on the rating plate.
1.2 C1-Master - units are not suitable for the
following applications:
- in areas where there is a risk of explosion
- for medical applications
- for working on moist materials
1.3 Ensure that all regulatory requirements are
observed during use
- always wear protective glasses
- provide enough light at the working place
- use dust suction
1.4 Unter no circumstances should the
motor handpiece be cleaned with
compressed air.
1.5 Before putting the handpiece down, always
insert a rotary instrument or the pin, supplied
with the unit, into chuck.
Caution:
- When using rotary instruments, do not
exceed the maximum speeds laid down by
their manufacturer.
- Repairs and other technical procedures must
only be carried out by suitable qualified
- personnel, authorized by SCHICK.
- SCHICK do not guarantee the C1 Master unit
should it not have been used in accordance
with the operating instructions.
2. Range of applications
The C1 Master unit is designed for universal use in
dental laboratories when trimming crowns and
bridges, respectively acrylic and light chrome cobalt
dentures.
With its speed range from 1.000 - 40.000 rpm the
SCHICK C1 Master - unit allows to work all dental
materials.
The motorhandpiece is ergonomical, small shaped
and runs smoothly, thus eliminating user-fatigue
and making it economical to use over long periods.
The progressive processor controller constantly
monitors the unit for overloading. A second
thermal fuse, which is independent of the
computer, provides further protection. Thus the
C1 Master - unit offers a maximum of safety.
Conditions of environment:
- interior 5° - 40° C.
- up to 2,000 meter over sea level
Categorie of overvoltage: II
Grade of pollution: 2
WEEE-Reg.-Nr. DE78620387
2

3
3. Summary C1-Master units
12
C1/SK complete
article no. 3505
C1/SF complete
article no. 3510
C1/ST complete
article no. 3515
Accessories:
digital indicator
article no. 6380
NH / DNH
riveting hammer(1)
article no.1850
twin riveting hammer(2)
article no. 1860
C1/MA
C1-Master Motor with INTRAmatic-coupling
article-no. 3500/03

4
5
6
3
8
9
1
2
4
7
4. List of contents - accessories/spare parts
C1/SK
C1/SK
C1/MH
C1/SK-D
C1/SK-D
C1/MH
C1/SF
C1/SF
C1/MH
C1/SF-D
C1/SF-D
C1/MH
C1/ST
C1/ST
C1/MH
spare parts
Chucks:
Standard:
Optional: ,00mm
chuck key
counter stay wrench
motor cable complete
Ø 2,35mm
Ø 3
article-no.
3505
3535
3500
9127
2160
5614
3170
3505/1
3535/1
3500
9127
2160
5614
3170
6380
article-no.
3510
3540
3500
9127
2160
3510/1
3540/1
3500
9127
2160
6380
article-no.
3515
3545
3500
6371
9127
2160
6642
6643
4115
6223
3560
10
complete
knee controller 1
motorhandpiece and cable 2
handpiece rack - with two
keys for changing chuck 3
mains cable 4
suspension strip 5
screws - 2 pieces - 6
with digital indicator complete
knee controller with attachment
for digital indicator 1
motorhandpiece and cable 2
handpiece rack - with two
keys for changing chuck 3
mains cable 4
suspension strip 5
screws - 2 pieces - 6
digital indicator 7
complete
foot controller 8
motorhandpiece and cable 2
handpiece rack - with two
keys for changing the chuck 3
mains cable 4
with digital indicator complete
foot controller with attachment
for digital indicator 8
motorhandpiece and cable 2
handpiece rack - with two
keys for changing the chuck 3
mains cable 4
digital indicator 7
complete
control unit table top model 9
motorhandpiece and cable 2
dynamic foot-switch 10
handpiece rack - with two
keys for changing the chuck 3
mains cable 4

5
2
18
18
2
8
19
1
9
3
11
12
21
22
20
24
5
4
6
1
1
23
2
5. Setting up
Operating the different versions
operating with digital indicator see discription
on page 6
all versions
5.1 Ascertain, that your mains supply coincides with
the data on the rating system.
5.2 Plug the mains cable 9 into the unit 1 and into
a mains socket.
5.3 Plug the motor cable 3 into the socket 2 on the
rear of the unit (quarter-turn catch).
5.4 Place the handpiece on the rest 8 supplied with it.
knee controller version only
5.5 Press the mains switch 4 on the front of the unit.
The control lamp will come on. The unit is switched.
off by pressing the mains switch 4 again.
5.6 Set the speed controller 5 to the desired speed.
The set speed can be reached right away by
pressing the knee controller 6.
foot controller version only.
5.5 Press the mains switch 11 on the front of the unit.
The LED will flash up. The unit is switched
off by pressing the mains switch 11 again.
5.6 The speed can be varied progressively between
1.000 - 40.000 rpm by moving the foot pedal 12.
bench controller version only
5.5 Plug the dynamic foot-switch 21 into the
socket 23 on the rear of the unit
(quarter-turn-catch).
5.6 Switch on the mains switch 20 on the front of the
unit (the control lamp lights up). The unit is
switched off by pressing the mains switch 20 again.
5.7 Set the speed control knob 22 to the desired speed.
(see digital display 24) The motor can be switched
on or off by moving the pedal and the speed can
be varied progressively up to the set speed.
5.8 The bench unit can also be operated without the dynamic
foot-switch. Set the speed control knob 22 to the
desired speed. The motor will begin to run immediately.

6
zu
auf
digitaldigital
digitaldigital
digitaldigital
SCHICKSCHICK
SCHICKSCHICK
SCHICKSCHICK
x1000/m in
x1000/m in
x1000/m in
x1000/m in
x1000/m in
x1000/m in
13
6. Operating the unit with a digital
display
knee and foot models only
Insert the plug on the digital display 19 into the
socket 18 in the rear of the unit.
When the unit is switched on, the digital speed
indicator shows the pre-selected maximum speed.
Once the motor is running, the actual speed
of the motor is displayed.
To save space, the digital speed indicator can be
placed under the handpiece rack or, if required,
adhered to a bench top with double-sided
adhesive tape.
table top unit
into the table top unit a digital display is integrated -
the display operates in the same way as
described above.
7. Exchanging the rotary instruments
The chuck is opened, respectively, closed by
turning the outer sleeve 13 of the handpiece.
Caution:
Only ever exchange the rotary instrument with the
motor switched off!
With regard to the precision and service-life of the
chuck, an instrument must always be inserted into it
- even when the handpiece is not in use.

7
8. Replacing the chuck
8.1 Remove the motor cable 15. To do so unscrew the
cap 16 from the motor and loosen the cable by
pulling out the plug-in seal 17.
8.2 Open the chuck and withdraw the rotary instrument.
8.3 Remove seeling cap 24
8.4 Use a number 6223 wrench 23 to hold the motor
end of the spindle. Insert the chuck tool
No. 4115 22. Hold the number 6223 23 wrench
tightly and turn the chuck tool anti clockwise to
unscrew the chuck completely.
- the chuck has a right-handed thread!
8.5 Clean the chuck, grease it lightly and place it
in the spindle. Use the tools to screw the chuck
in - clockwise and as far as possible - as described
in section 8.4 - and tighten it slightly.
Replace the plug-in seal 17 and screw the cap 16
back into place. Replace the sealing cap 24 again.
Please note:
The tools 22 and 23 are to be found in the
base of the handpiece rack!
9. Care and maintenance
Caution: Do not clean your C1 Master
motorhandpiece with compressed air!
Chuck: should be cleaned and re-greased once in
a while, depending on how dirty it is.
As C1 Master units have no commutators,
carbon brushes or ventilation parts, no further
maintenance is required.
10. Possible faults
Should the handpiece be overloaded, respectively,
jammed, for safety reasons the unit will switch itself
off.
- Release knee/foot switch and operate it again; the
unit is ready for use immediately
bench controller version only
- When using the bench version without a pedal
switch, the speed control knob should be turned to
" 0" , when the desired speed is selected again; the
unit is ready for use immediately.
- When using the bench version with a pedal switch
it should be released and operated again; the unit is
then ready for use again.
all versions
if the unit should not be running after doing as
described above the 2 fuses have to be checked and
eventually exchanged.
The fuses (2x T2AH250V/2x T4AH100V-115V)are to
be found at the rear of the unit beneath the socket 1.
16
15
24
17
22
23
4115
6230 Ø 2,35 mm
6228 Ø 3,00 mm
6642 Ø 2,35 mm
6643 Ø 3,00 mm
6223
3446
5133
3449
3420
3560
1
24
24

8
11. Technical Data
C1/SK C1/SF C1/ST
Dimensions: Width 107mm 225mm 225mm
Height 243mm 110mm 110mm
Dept 253mm 170mm 170mm
Weight 3,7 kg 3,0 kg 2,9 kg
C1/MH Length 158mm Weight 200g
Power Supply: AC 220-240V 115V 100V
Nominal frequency: 50/60Hz
Power input: 175W
Type: C1 Master
Speed range: 1.000 - 40.000 min rpm
Torque max.: 5,0 Ncm
Safety class: I
The oscillation total value during
operation is below 2,5m/s²(EN 28662).
This unit complies with the current VDE(German
association of electrical technicians) regulations
concerning safety and suppression.
These operating instructions should be readily
accessible and are best kept close to the unit itself.
We would like to take this opportunity to advise you
that a proper repair service and suitable qualified
personnel are required for such highly developed
technical equipment.
SCHICK guarantees to carry out perfect repairs using
original spare parts.
12. Declaration of Conformity
We, SCHICK GmbH
Lehenkreuzweg 12
88433 Schemmerhofen
declare herewith, that the product
C1 Master installations consisting of
C1 Motorhandpiece 3500 connected with
C1 Control unit 3535, 3540 and 3545
is in conformity with the following provisions of Directive:
2006/42/EG (machinery directive)
2014/30/EU (EMV directive)
Name and address of
person in charge:
Schemmerhofen, February 2016
W. Schick
managing director
manufacturer:
Wolfgang Schick
Lehenkreuzweg 12
88433 Schemmerhofen
D20521
02/16 bg
Subject to technical modification without prior notice