Schick CDRPan User manual

CDRPan®
FOR PANORAMIC SYSTEMS
Installation
Instructions for Villa Rotograph
Schick Technologies, Inc.
31-00 47th Avenue
Long Island City, New York
11101
[phone]
[phone] (FAX)
Part Number B1051105 Rev. –
F:\GENERAL\DEPTS\QA\DOCUMENT\B1051105Rev-.doc

Copyright ©2000 by Schick Technologies, Inc.
All Rights Reserved
Many of the designations used by manufacturers and sellers to
distinguish their products are claimed as trademarks. Where those
designations appear in this document, and Schick Technologies, Inc.
was aware of a trademark claim, the designations have been printed in
ca
p
s or initial ca
p
s.
Part Number
B1051105 Rev. –
September 12, 2000

Printed in the United States of America
This document was originally prepared in English

Contents
1. Introduction...................................................................................................1
1.1. Welcome...........................................................................................................................1
1.2. CDRPan System...............................................................................................................1
1.3. Overview for Installing CDRPan .....................................................................................1
1.4. Before You Start Installing CDRPan................................................................................2
2. What You Will Need For Installation.........................................................3
2.1. CDRPan System...............................................................................................................3
2.2. Tools.................................................................................................................................6
3. Sensor and Codestrip.................................................................................7
3.1. Remove Rotation Arm Cover Plate..................................................................................7
3.2. Install Sensor Assembly ...................................................................................................8
3.3. Install Sensor Clip ............................................................................................................9
3.4. Route Sensor Cable ........................................................................................................10
3.5. Check Sensor Cable Run................................................................................................11
3.6. Install Codestrip Assembly.............................................................................................12
3.7. Install Interlock Defeater................................................................................................13
3.8. Secure Sensor Assembly ................................................................................................15
3.9. Check Codestrip Alignment ...........................................................................................16
3.10.Reinstall Rotation Arm Cover Plate...............................................................................18
4. Remote Module, Power Supply, and PCI Board................................. 19
4.1. Install Remote Module...................................................................................................19
4.2. Install Power Supply.......................................................................................................20
4.3. Install PCI Board............................................................................................................20
Rotograph Installation B1051105 Rev. – i

Safety Issues
Electrical Concerns
CDRPan conforms to national (U.S.) and international standards for electromagnetic
compatibility and electrical safety. A complete list of specifications can be found in the
CDRPan User’s Guide.
Mechanical Considerations
The sensor package, the remote module, and the cables of the CDRPan system are
mounted outside of the patient area to ensure patient safety and reliable equipment
operation.
Radiation Concerns
No adjustments or alterations are made to the X-ray source of the panoramic equipment.
B1051105 Rev. – Rotograph Installationii

1. Introduction
1.1. Welcome
The CDR Panoramic X-ray System (“CDRPan”) is an electronic imaging system that
integrates with panoramic machines to acquire, display, store and print digital X-rays.
Because of its digital format, the X-ray can be enhanced for more detail using CDR tools,
and it can be archived for patient histories and retrieved for comparisons.
1.2. CDRPan System
The CDRPan system hardware consists of the following components (unless otherwise
indicated, all part numbers (P/Ns) refer to Schick Technologies numbers):
•CDRPan kit for Villa Rotograph (P/N B4760050) which includes the sensor,
codestrip, other attaching parts, and accessories.
•Remote module (P/N B4750100)
•Power supply (P/N A3302300)
•PCI board (P/N B3301100) and cable (B2211001).
The CDRPan system requires the following software:
•CDR software (version 2.1 or higher)
•CDRPan installation disk, which includes the PCI board device driver and the
series set to be used with panoramic exams
1.3. Overview for Installing CDRPan
This Installation Manual is one of two documents you will need to install the CDRPan
system completely. After performing the installation procedures in this document, you
should refer to the CDRPan User’s Guide (P/N B1051008) to install the software for the
CDRPan system. Procedures for installing CDRPan system hardware and software are
provided below.
PROCEDURE DOCUMENT
Install Sensor and Codestrip (This Manual)
Install Remote Module and Power Supply (This Manual)
Install PCI Board (This Manual)
Install PCI Device Driver CDRPan User Guide
Install CDR and CDRPan Software CDRPan User Guide
Rotograph Installation B1051105 Rev. – 1

1.4. Before You Start Installing CDRPan
Prior to installing CDRPan on your panoramic system, please perform the following
checks.
A. Make sure your panoramic system is operating properly.
B. Familiarize yourself with the installation steps before performing them.
C. Determine the location of your computer. This will be useful when you install the
Remote Module and need to run cables between it and your computer.
ROTATION
ARM
X-RAY
SOURCE
FACEPLATE
Figure 1. Picture of the Villa Rotograph
B1051105 Rev. – Rotograph Installation2

2. What You Will Need For Installation
2.1. CDRPan System
To perform the installation procedures in this manual, you will need the following
CDRPan parts and assemblies.
A. Sensor Assembly
B. Curved Cassette Codestrip Assembly (A), Mounting Clip (B), and Interlock
Defeater (C)
B
A
C
Rotograph Installation B1051105 Rev. – 3

C. Remote Module
D. Cable Holders and Clamps
E. Power Supply
B1051105 Rev. – Rotograph Installation4

F. PCI Board
G. Data Cable for PCI Board
H. X-ray Filter and Allen Keys
Rotograph Installation B1051105 Rev. – 5

2.2. Tools
To install the sensor and codestrip, you will need the following tools.
A. Phillips screwdriver to remove and replace rotation arm cover plate, and to install
sensor clip, codestrip assembly, and interlock defeater.
B. Allen wrench (hex key, 3/32 in.) to adjust clearance between encoder and codestrip.
C. Allen wrench (hex key, 0.050 in.) to secure sensor clip.
B1051105 Rev. – Rotograph Installation6

3. Sensor and Codestrip
3.1. Remove Rotation Arm Cover Plate
Using a Phillips screwdriver, remove screw from bottom of plate and remove plate from
rotation arm.
Rotograph Installation B1051105 Rev. – 7

3.2. Install Sensor Assembly
Carefully slide sensor assembly into faceplate until upper guide is seated firmly at top of
aperture slit and lower guide fits in bottom of aperture.
UPPER
GUIDE
LOWER
GUIDE
B1051105 Rev. – Rotograph Installation8

3.3. Install Sensor Clip
Install the sensor clip at the bottom of the aperture and secure it in place using the Allen
key (.050 in) to tighten 2 screws.
CAUTION: Light tension on the set screws is all that
is needed to secure the sensor clip. Do not apply
excessive torque.
Rotograph Installation B1051105 Rev. – 9

3.4. Route Sensor Cable
Use cable clamps and holders to route sensor cable to the top of the panoramic machine.
Allow enough slack in the cable for the rotation arm of the panoramic machine to move
freely.
Sensor cable secured along faceplate
Sensor cable secured across faceplate
B1051105 Rev. – Rotograph Installation10

3.5. Check Sensor Cable Run
Swivel the arm of the panoramic machine to ensure there is enough slack in the cable for
the rotation arm to move freely. Adjust cable if necessary.
Sensor cable secured along rotation arm
Rotograph Installation B1051105 Rev. – 11

3.6. Install Codestrip Assembly
A. Install the codestrip assembly on the drum cassette holder by tightening screws with a
Phillips screwdriver.
B. Align the codestrip assembly with the encoder window.
CODESTRIP
CASSETTE
HOLDER
CODESTRIP
ENCODER
WINDOW
B1051105 Rev. – Rotograph Installation12

3.7. Install Interlock Defeater
A. Slide the interlock defeater onto the drum cassette holder. Make sure that it fits over
and depresses the interlock limit switch on the panoramic machine.
Rotograph Installation B1051105 Rev. – 13

B. When the interlock defeater is firmly in place, secure it to the cassette holder using a
Phillips screwdriver to tighten 4 screws.
B1051105 Rev. – Rotograph Installation14

3.8. Secure Sensor Assembly
Adjust the encoder section of the sensor assembly to approximately 1 mm from the
codestrip on the drum cassette. Use the Allen key (3/32 in.) to tighten the hinge links on
the encoder.
Rotograph Installation B1051105 Rev. – 15

3.9. Check Codestrip Alignment
A. Check the encoder-to-codestrip alignment. The proper distance between these two
parts should be approximately 1 mm when the arm of the panoramic machine is
rotated. Verify this distance at the start and at the end of motion.
Start of Panoramic Motion
End of Panoramic Motion
B1051105 Rev. – Rotograph Installation16