Schlage KC9000-LG User manual

KING COBRA/KING COBRA-2
NARROW STILE SERIES
57055-B 04-2007
KC9000-LG
KC9000 Latch Guard

KC9000/KC9000-2 LATCH GUARD INSTALLATION
Introduction / Tools and Materials Needed / Contact Info
57055-B Page 2 04-2007
KC9000/KC9000-2 LATCH GUARD INSTALLATION
Introduction / Tools and Materials Needed / Contact Info
Introduction
The KC9000 Latch Guard, when installed in addition to the KC9000 Narrow Stile Trim, adds
an added level of security to outswinging doors. The KC9000 Latch Guard covers the opening
at the critical area between door and frame. Silver coated for environmental protection.
Tools and Materials Needed Not Included in Box:
Contact Information:
Schlage Lock Company
575 Birch Street
Forestville, CT 06010
technical support: 866-322-1237
fax: [phone]
web: http://www.irsupport.net
1
.F
l
at
h
ea
d
screw
d
r
i
ver w
/
stra
i
g
h
t,
1/8”
w
id
e
bl
a
d
e
2. 1/16” Allen wrench
3. Pencil
4. Center punch
5. Hammer
6. Power drill
7. 1/8” drill bit
8. 7/16” drill bit
9. 11/32” drill bit
10. Drill and Tap for 10-32 threads
11. Socket wrench set

KC9000/KC9000-2 LATCH GUARD INSTALLATION
Installing the KC9000-LG
57055-B Page 3 04-2007
Installing the KC9000-LG
1) Prepare Door:
New Construction-Start Here
• Remove all existing trim from outside of door.
• Remove backing from sticky template provided.
• Refer to Figure 1. Apply sticky template to area on stile where
trim
• was removed.
• Center 1-1/4” circle on template with existing cylinder hole (a).
• Use vertical lines on template to insure that template is applied
square to stile.
NOTE: The lines on the edges of template are for vertical guidance only.
Do not line them up with edges of door stile. Template can be lifted and
repositioned as often as required to get the position correct.
• Centerpunch the three small holes on template marked, TAP 10-
32 (b).
• Remove the sticky template.
• Drill and tap (10-32) the three holes (b).
b
b
a
Figure 2
Figure 1
Figure 3 Figure 4
Retrofit Installation - Start Here
• Refer to Figure 2. Place Latch Guard on door stile and align
with the 3 tapped holes (a).
• Refer to Figures 3 and 4. Outline the two, 3/8” square holes at
the top and bottom of the Latch Guard.
a
a

KC9000/KC9000-2 LATCH GUARD INSTALLATION
Installing the KC9000-LG
57055-B Page 4 04-2007
2) Mount the Latch Guard:
•
S
et t
h
e Latc
h
G
uar
d
as
id
e.
> You should have two, 3/8” squares marked on door stile, 15” apart (a).
• Draw diagonal lines connecting opposite corners within each square (b).
• Centerpunch at the point where the lines intersect within each square (c).
> This marks the center of each square.
• Using a 1/8” drill bit, create a pilot hole at the center of both squares.
> Drill completely through door stile.
• Using a 11/32” drill bit, create a 11/32” hole at both of the 1/8” pilot holes
that you just drilled.
> Drill completely through door stile.
> Drilling can be done from either side of the door.
WARNING: USE CAUTION ON NEXT STEP ! DO NOT DRILL THROUGH
DOOR !
• Install a 7/16” drill bit into hand drill.
• From trim-side of door stile, create a 7/16” hole at both of the 11/32” holes
that you just drilled. DO NOT DRILL COMPLETELY THROUGH
DOOR! ONLY DRILL THROUGH TRIM-SIDE OF DOOR STILE. c
b
a
• Re
f
er to F
i
gure 5. Mount Latc
h
G
uar
d
on tr
i
m-s
id
e o
f
d
oor st
il
e.
> Align both square holes in Latch Guard with the two, 7/16”
holes that you drilled in door stile.
• From trim-side of door, insert both Carriage Bolts (a) into the two
square holes in Latch Guard.
> It may be necessary to turn the Carriage Bolts a little so that the
square portion of the bolts fully insert into square holes in
Latch Guard.
> Domed head of both bolts should be flush with surface of Latch
Guard.
Figure 5
a

KC9000/KC9000-2 LATCH GUARD INSTALLATION
Installing the KC9000-LG
57055-B Page 5 04-2007
3) Secure the Latch Guard:
• Re
f
er to F
i
gure
6
. From t
h
e
i
ns
id
e o
f
d
oor,
i
nsta
ll
the remaining provided hardware onto the Carriage
Bolts:
> Slide a flat washer onto each Carriage Bolt.
> Spin a Blind Nut (a) onto each Carriage Bolt.
> Using a socket wrench, tighten both Blind Nuts.
a
a
Figure 6

KC9000/KC9000-2 LATCH GUARD INSTALLATION
Installing the KC9000-LG
57055-B Page 6 04-2007
4) Installing the Trim (KC9111 and KC9321 ONLY):
The
f
ollow
i
ng perta
i
ns only to K
C9111
and KC9321. If you are installing any-
thing other than a KC9111 or KC9321,
skip to Step 5.
• Refer to Figure 7. Insert the adapter into the 1-
1/4” round hole in the door stile, then place
the spacer over the top of the adapter.
• Refer to Figure 8. Mount the KC9111 or
KC9321 narrow stile trim on top of the Latch
Guard.
• Using a ball-end Allen wrench, secure with the
three, pre installed Allen head screws.
• Proceed to Step 6: Finish Installing the Trim
(All Models): on page 8
Figure 7
Figure 8

KC9000/KC9000-2 LATCH GUARD INSTALLATION
Installing the KC9000-LG
57055-B Page 7 04-2007
5) Installing the Trim (All models except KC9111 and KC9321):
The
f
ollow
i
ng perta
i
ns to all models except
KC9111 and KC9321.
• Refer to Figure 9.Install the adapter on the trim:
> Place the spacer on the back of the trim.
> Insert the adapter over the top of the spacer.
• Refer to Figure 10. Mount trim on top of Latch
Guard.
> Using a ball-end Allen wrench, secure with the
three, pre installed Allen head screws.
• Proceed to Step 6: Finish Installing the Trim (All
Models): on page 8
Figure 9
Figure 10

KC9000/KC9000-2 LATCH GUARD INSTALLATION
Installing the KC9000-LG
57055-B Page 8 04-2007
6) Finish Installing the Trim (All Models):
7) Test the Installation:
• Close the door and test the lock to verify that it is functioning properly.
> For models with a lever: Lever should be able to be pushed down, but not up.
> For models with a turnpiece: Turnpiece should rotate clockwise for Right Hand/Right
Hand Reverse and counterclockwise for Left Hand/Left Hand Reverse.
> For models with a T-Handle: T-Handle should rotate freely.
> For models with a knob: Knob should rotate freely.
• Insert key into cylinder and rotate it counterclockwise.
> Lever, turnpiece, T-Handle or knob should retract latch.
NOTE: The key should only rotate counterclockwise, not clockwise.
• Rotate key back to original position and remove it.
> Lever, turnpiece, T-Handle or knob should no longer retract latch.
• Using the keypad, enter the default access code: 1 3 5 7 9.
> The red LED should light each time the first four numbers are pressed and when the 9 is
pressed, the green LED should flash for five seconds during which time the lever, turn-
piece, T-Handle or knob should retract the latch.
• Test inside egress device (paddle/exit device, etc.) to make sure it is properly operating.
SEE THE PROGRAMMING GUIDE FOR PROGRAMMING INFORMATION.
• Insta
ll
t
h
e
b
atter
i
es an
d
t
h
e
b
attery cover.
> Instructions for installing the batteries and the battery cover are included in most KC9000
Narrow Stile Installation Manuals, e.g., Form #57040.