Schlage LE162 Wiring diagram

1
Installation Instructions & User Guide:
Wireless Keypad Lock LE162
Keep the below information in a safe and secure place for future reference.
IMPORTANT INFORMATION
Lock Programming Code
Six (6) digits
For security reasons, this code is chosen randomly and not held
on any database. If this code is lost, Customer Support will be
unable to assist. It is suggested you hold this code in a safe and
secure location, or change the code to your own, unique number.
FOLD
FRONT COVER FLAP
PLEASE NOTE

MANUAL PROGRAMMING FUNCTIONS
• Pressthekeysonthekeypadasshowninthefollowingsteps. • Waitfortheconrmationindicatorbeforeproceedingtothenextstep. • Ifyoumakeamistake,waitforalllightsandbeepstostopandthenstartoverfromthebeginning. PC-ProgrammingCode(seepage16) UC-UserCode(seepage16)
1 Enable All User Codes function is available only when user codes are currently disabled. 2 Delete All User Codes function will remove ALL user codes, but will not change the programming code. User Codes cannot be recovered after this function is completed.
If an incorrect code is entered, the LED will ash red twice and beep twice.
Add
UserCode
Enter Programming Code
(Six Numbers)
Enter Programming Code
(Six Numbers)
Enter Programming Code
(Six Numbers)
Enter Programming Code
(Six Numbers)
Enter Programming Code
(Six Numbers)
Enter Programming Code
(Six Numbers)
Enter Programming Code
(Six Numbers)
Press Press Press Press Press Press Press
Enter NEW User Code
(Four Numbers)
Enter UNWANTED
User Code (Four Numbers)
Enter NEW Programming
Code (Six Numbers)
Enter Programming Code
(Six Numbers)
Re-enter NEW User Code
(Four Numbers)
Re-enter UNWANTED
User Code (Four Numbers)
Re-enter NEW Programming
Code (Six Numbers)
Enter Programming Code
(Six Numbers)
Wait for
3 Lights + 3 Beeps
Wait for
3 Lights + 3 Beeps
Wait for
3 Lights + 3 Beeps
Wait for
3 Lights + 3 Beeps
Wait for
3 Lights + 3 Beeps
Wait for
3 Lights + 3 Beeps
Wait for
3 Lights + 3 Beeps
Wait for
3 Lights + 3 Beeps
Wait for
3 Lights + 3 Beeps
Wait for
3 Lights + 3 Beeps
Wait for
3 Lights + 3 Beeps
Success!
1 Long Light + 1 Long Beep
Wait for
3 Lights + 3 Beeps
Success!
Blinking
Wait for
3 Lights + 3 Beeps
Wait for
3 Lights + 3 Beeps
Wait for
3 Lights + 3 Beeps
Success!
1 Long Light + 1 Long Beep
Success!
1 Long Light + 1 Long Beep
Success!
1 Long Light + 1 Long Beep
Success!
1 Long Light + 1 Long Beep
Success!
1 Long Light + 1 Long Beep
Delete
UserCode
Change
Programming
Code
EnableVacation
Mode
(DisableAll)
Disable Vacation
Mode
(Enable All)1
Enable/Disable
Beeper
DeleteAll2
UserCodes
PutLock
inEnrolment
Mode 3
FOLD
INSIDE FRONT COVER - UNFOLDED

1
Installation Instructions & User Guide:
Wireless Keypad Lock LE162
CONTENTS
Contents of the box.................................................................................. 2
How to install your lock ............................................................................ 3
- Door preparation.................................................................................... 3
- Lock installation............................................................................... 9
- Template (see inside back cover)................................................... IBC
Lock Parts............................................................................................... 15
Codes...................................................................................................... 16
- Programming and user codes ......................................................... 16
- Manual programming codes........................................................... 17
Replacing batteries ................................................................................. 16
Functions................................................................................................ 18
- Operating buttons.......................................................................... 18
- Operating guide ............................................................................. 18
- Restoring factory settings .............................................................. 19
- Vacation mode function................................................................. 19
Emergency override key.......................................................................... 20
Troubleshooting...................................................................................... 21
Glossary .................................................................................................. 23

2
CONTENTS OF THE BOX
TOOLS NEEDED
Phillips Screwdriver Side Cutters Tape Measure Pencil
Chisel Hammer54mm Hole SawDrill (3mm, 12mm,
25mm bits)

3
HOW TO INSTALL YOUR LOCK
1. Door preparation
32mm-45mm
1.1 Measuredoorwidth.
If the door is thinner
than 32mm or thicker
than 45mm, then the
lock will not t properly
on the door.
1.2 Marklockcentrelineon
 doorfaceanddooredge.
Door face
Door edge
Recommend between
1040mm and 1100mm from oor.

4
1. Door preparation (continued).
 1.3 Markanddrill54mmand12mmholes.(Seeinsidebackcoverfortemplate).
12mm drill bit
54mm hole saw
B. C.
30mm
100mm
95mm
60mm
A.
32mm-45mm

5
1.4 Markanddrill25mmholeindooredge.
A. B.
½ door
width
25mm drill bit
C. D.

6
1. Door preparation (continued).
E. F.
G. H.

7
7
1.5 Measureandmarkdoorjambforstrike.
A. Measure from oor and mark on door jamb.
B. Mark centre for strike hole exactly opposite latch hole.
A.
Door jamb
Latch hole
Recommended between
1040mm and 1100mm
from oor
Recommended between
1040mm and 1100mm
from oor
B.

8
1. Door preparation (continued).
C. As shown, chisel a hole in marked area, depth of 15mm.
D. Line up dust box and strike with hole in door jamb.
E. Use pencil to trace strike and mark holes.
F. Drill two (2) 3mm pilot holes and use chisel to create strike mortice, 2mm deep.
G. Position dust box and strike and screw into place.
C.
21mm
31mm
D.
E.
12mm drill bit
F.
G.