Schumacher Electric DY-1420 User manual

0099001066-01
Voltage: 12
Amperage: 2, 20, 55
Manual Battery Charger
Model: DY-1420
OWNER’S MANUAL
READ THE ENTIRE MANUAL BEFORE USING THIS PRODUCT.
FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY OR DEATH.
DO NOT RETURN THIS PRODUCT
TO THE STORE!
Call Customer Service for Assistance:
800-621-5485
PELIGRO
NO use el cargador de baterías hasta que haya leído y comprendido
completamente el manual del usuario.Si usted desea una versión en
español de esta edición, visite nuestra página en la red localizada en www.batterychargers.
com así podrá obtener un instructivo del cargador de baterías en español. Si usted no tiene
acceso a la red y necesita asistencia, llame Servicios al Cliente al [phone].

•1 •
IMPORTANT: READ AND SAVE THIS SAFETY AND INSTRUCTION MANUAL.
SAVE THESE INSTRUCTIONS – This manual will show you how to use your charger safely
and effectively. Please read, understand and follow these instructions and precautions
carefully, as this manual contains important safety and operating instructions. The safety
messages used throughout this manual contain a signal word, a message and an icon.
The signal word indicates the level of the hazard in a situation.
Indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury to the operator or bystanders.
Indicates a potentially hazardous situation which, if not avoided, could result
in death or serious injury to the operator or bystanders.
Indicates a potentially hazardous situation which, if not avoided, could result
in moderate or minor injury to the operator or bystanders.
Indicates a potentially hazardous situation which, if not avoided, could result
in damage to the equipment or vehicle or property damage.
Pursuant to California Proposition 65, this product contains chemicals
known to the State of California to cause cancer and birth defects or other
reproductive harm.
IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS1.
This manual contains important safety and operating instructions
RISK OF ELECTRIC SHOCK OR FIRE.
Keep out of reach of children.1.1
Do not expose the charger to rain or snow.1.2
Use only recommended attachments. Use of an1.3
attachment not recommended or sold by Schumacher® Electric
Corporation may result in a risk of re, electric shock or injury
to persons or damage to property.
To reduce the risk of damage to the electric plug or cord, pull by the plug rather than the1.4
cord when disconnecting the charger.
An extension cord should not be used unless absolutely necessary. Use of an improper1.5
extension cord could result in a risk of re and electric shock. If an extension cord must
be used, make sure:
That the pins on the plug of the extension cord are the same number, size and shape•
as those of the plug on the charger.
That the extension cord is properly wired and in good electrical condition.•
That the wire size is large enough for the AC ampere rating of the charger as•
specied in section 8.
To reduce the risk of electric shock, unplug the charger from the outlet before attempting1.6
any maintenance or cleaning. Simply turning off the controls will not reduce this risk.
Do not operate the charger with a damaged cord or plug; have the cord or plug replaced1.7
immediately by a qualied service person. (Call customer service at: 1-800-621-5485.)
Do not operate the charger if it has received a sharp blow, been dropped or otherwise1.8
damaged in any way; take it to a qualied service person. (Call customer service at:
1-800-621-5485.)
Do not disassemble the charger; take it to a qualied service person when service or 1.9
repair is required. Incorrect reassembly may result in a risk of re or electric shock. (Call
customer service at: 1-800-621-5485.)

•2 •
RISK OF EXPLOSIVE GASES.
WORKING IN THE VICINITY OF A LEAD-ACID BATTERY IS1.10
DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES DURING
NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF UTMOST
IMPORTANCE THAT YOU FOLLOW THE INSTRUCTIONS EACH TIME YOU
USE THE CHARGER.
To reduce the risk of a battery explosion, follow these instructions and those published by1.11
the battery manufacturer and the manufacturer of any equipment you intend to use in the
vicinity of the battery. Review the cautionary markings on these products and on the engine.
PERSONAL PRECAUTIONS2.
RISK OF EXPLOSIVE GASES.
NEVER smoke or allow a spark or ame in the vicinity of a battery or engine.2.1
Remove personal metal items such as rings, bracelets, necklaces and2.2
watches when working with a lead-acid battery. A lead-acid battery can produce
a short-circuit current high enough to weld a ring or the like to metal, causing a
severe burn.
Be extra cautious to reduce the risk of dropping a metal tool onto the battery. It might2.3
spark or short-circuit the battery or other electrical part that may cause an explosion.
Use this charger for charging LEAD-ACID batteries only. It is not intended to supply power2.4
to a low voltage electrical system other than in a starter-motor application. Do not use
this battery charger for charging dry-cell batteries that are commonly used with home
appliances. These batteries may burst and cause injury to persons and damage to property.
NEVER charge a frozen battery.2.5
NEVER overcharge a battery.2.6
Consider having someone close enough by to come to your aid when you work near a2.7
lead-acid battery.
Have plenty of fresh water and soap nearby in case battery acid contacts your skin,2.8
clothing or eyes.
Wear complete eye and body protection, including safety goggles and protective2.9
clothing. Avoid touching your eyes while working near the battery.
If battery acid contacts your skin or clothing, immediately wash the area with soap and2.10
water. If acid enters your eye, immediately ood the eye with cold running water for at
least 10 minutes and get medical attention right away.
If battery acid is accidentally swallowed, drink milk, the whites of eggs or water. DO NOT2.11
induce vomiting. Seek medical attention immediately.
PREPARING TO CHARGE3.
RISK OF CONTACT WITH BATTERY ACID. BATTERY ACID
IS A HIGHLY CORROSIVE SULFURIC ACID.
If it is necessary to remove the battery from the vehicle to3.1
charge it, always remove the grounded terminal rst. Make sure
all of the accessories in the vehicle are off to prevent arcing.
Be sure the area around the battery is well ventilated3.2
while the battery is being charged.
Clean the battery terminals before charging the battery. During cleaning, keep airborne3.3
corrosion from coming into contact with your eyes, nose and mouth. Use baking soda
and water to neutralize the battery acid and help eliminate airborne corrosion. Do not
touch your eyes, nose or mouth.
Add distilled water to each cell until the battery acid reaches the level specied by the 3.4
battery manufacturer. Do not overll. For a battery without removable cell caps, such
as valve regulated lead acid batteries (VRLA), carefully follow the manufacturer’s
recharging instructions.
Read, understand and follow all instructions for the charger, battery, vehicle and any3.5
equipment used near the battery and charger. Study all of the battery manufacturer’s
specic precautions while charging and recommended rates of charge.

•3 •
Determine the voltage of the battery by referring to the vehicle owner’s manual and3.6
make sure that the output voltage selector switch is set to the correct voltage. If the
charger has an adjustable charge rate, charge the battery in the lowest rate rst.
Make sure that the charger cable clips make tight connections.3.7
CHARGER LOCATION4.
RISK OF EXPLOSION AND CONTACT WITH
BATTERY ACID.
Locate the charger as far away from the4.1
battery as the DC cables permit.
Never place the charger directly above4.2
the battery being charged; gases from the
battery will corrode and damage the charger.
Do not set the battery on top of the charger.4.3
Never allow battery acid to drip onto the charger when reading the electrolyte specic 4.4
gravity or lling the battery.
Do not operate the charger in a closed-in area or restrict the ventilation in any way.4.5
DC CONNECTION PRECAUTIONS5.
Connect and disconnect the DC output clips only after setting all of the charger switches5.1
to the “off” position (if applicable) and removing the AC plug from the electrical outlet.
Never allow the clips to touch each other.
Attach the clips to the battery and chassis, as indicated in sections 6 and 7.5.2
FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN VEHICLE6.
A SPARK NEAR THE BATTERY MAY CAUSE
A BATTERY EXPLOSION. TO REDUCE THE
RISK OF A SPARK NEAR THE BATTERY:
Position the AC and DC cables to6.1
reduce the risk of damage by the hood, door
and moving or hot engine parts. NOTE: If
it is necessary to close the hood during the
charging process, ensure that the hood does not touch the metal part of the battery clips
or cut the insulation of the cables.
Stay clear of fan blades, belts, pulleys and other parts that can cause injury.6.2
Check the polarity of the battery posts. The POSITIVE (POS, P, +) battery post usually6.3
has a larger diameter then the NEGATIVE (NEG, N, -) post.
Determine which post of the battery is grounded (connected) to the chassis. If the6.4
negative post is grounded to the chassis (as in most vehicles), see step 6.5. If the
positive post is grounded to the chassis, see step 6.6.
For a negative-grounded vehicle, connect the POSITIVE (RED) clip from the battery6.5
charger to the POSITIVE (POS, P, +) ungrounded post of the battery. Connect the
NEGATIVE (BLACK) clip to the vehicle chassis or engine block away from the battery.
Do not connect the clip to the carburetor, fuel lines or sheet-metal body parts. Connect
to a heavy gauge metal part of the frame or engine block.
For a positive-grounded vehicle, connect the NEGATIVE (BLACK) clip from the battery6.6
charger to the NEGATIVE (NEG, N, -) ungrounded post of the battery. Connect the
POSITIVE (RED) clip to the vehicle chassis or engine block away from the battery. Do
not connect the clip to the carburetor, fuel lines or sheet-metal body parts. Connect to a
heavy gauge metal part of the frame or engine block.
Connect charger AC supply cord to electrical outlet.6.7
When disconnecting the charger, turn all switches to off, disconnect the AC cord, remove6.8
the clip from the vehicle chassis and then remove the clip from the battery terminal.
See CALCULATING CHARGE TIME for length of charge information.6.9

•4 •
FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE VEHICLE7.
A SPARK NEAR THE BATTERY MAY CAUSE
A BATTERY EXPLOSION. TO REDUCE THE
RISK OF A SPARK NEAR THE BATTERY:
Check the polarity of the battery posts.7.1
The POSITIVE (POS, P, +) battery post usually
has a larger diameter than the NEGATIVE
(NEG, N, -) post.
Attach at least a 24-inch (61 cm) long 6-gauge (AWG) insulated battery cable to the7.2
NEGATIVE (NEG, N, -) battery post.
Connect the POSITIVE (RED) charger clip to the POSITIVE (POS, P, +) post of the battery.7.3
Position yourself and the free end of the cable you previously attached to the NEGATIVE7.4
(NEG, N, -) battery post as far away from the battery as possible – then connect the
NEGATIVE (BLACK) charger clip to the free end of the cable.
Do not face the battery when making the nal connection.7.5
Connect charger AC supply cord to electrical outlet.7.6
When disconnecting the charger, always do so in the reverse order of the connecting7.7
procedure and break the rst connection while as far away from the battery as practical.
A marine (boat) battery must be removed and charged on shore. To charge it onboard7.8
requires equipment specially designed for marine use.
GROUNDING AND AC POWER CORD CONNECTIONS8.
RISK OF ELECTRIC SHOCK OR FIRE.
This battery charger is for use on a8.1
nominal 120-volt circuit and has a grounded
plug that looks like the plug illustrated. The
charger must be grounded to reduce the risk of
electric shock. The plug must be plugged into
an outlet that is properly installed and grounded
in accordance with all local codes and ordinances. The plug pins must t
the receptacle (outlet). Do not use with an ungrounded system.
8.2 Never alter the AC cord or plug provided – if it does not t the outlet,
have a proper grounded outlet installed by a qualied electrician. An improper
connection can result in a risk of an electric shock or electrocution.
NOTE: Pursuant to Canadian Regulations, use of an adapter plug is not allowed in Canada.
Use of an adapter plug in the United States is not recommended and should not be used.
Recommended minimum AWG size for extension cord:8.3
100 feet (30.5 meters) long or less – use a 10 gauge (5.26mm• 2) extension cord.
Over 100 feet (30.5 meters) long – use an 8 gauge (8.36mm• 2) extension cord.
ASSEMBLY INSTRUCTIONS9.
It is important to fully assemble your charger before use. Remove all cord wraps and9.1
uncoil the cables prior to using the battery charger. Follow these instructions for assembly.
PARTS TOOLS NEEDED
(2) 10-32, thread cutting screws
(4) ¼-20, thread cutting screws
(2) wheels
(1) axle
(2) axle caps
(2) axle brackets
(1) handle
(1) foot
3/8" wrench (for mounting foot)
5/16" wrench (for mounting wheels)
1/4" wrench (for mounting handle)
hammer
screwdriver (at blade)
screwdriver (Phillips)

•5 •
Attach the Foot:9.2 Remove the charger from the packing materials
and place upside down on a at surface. Attach the foot and secure it with
the four ¼-20 thread cutting screws provided.
Assemble the Wheels and Axle9.3 : Hold the axle
upright on the oor or work surface. Then, using a
hammer, tap one of the axle caps onto the top end
of the axle. Be sure to tap the axle cap on straight.
Slide both wheels onto the axle with the recessed
hubs facing out as shown. Install the second axle cap.
Mount the Axle to the Charger9.4 : Place
one end of each bracket into the slot on the
bottom of the charger. Place the axle assembly
under each bracket. Attach the brackets using
the two, 10-32 thread cutting screws provided.
NOTE: Be careful not to drop the brackets inside
of the charger case.
Attach the Handle9.5 : Turn the charger right side up onto its foot
and wheels. Remove the two top screws from each side of the
charger. Align the handle so the screw holes are aligned with
the screw holes on each side of the charger. Attach the handle
using the same screws you previously removed.
CONTROL PANEL10.
Ammeter
The Ammeter indicates the amount of current, measured in amps, that is being drawn
by the battery. As a battery takes on a charge, it draws less current from the charger.
Correspondingly, the meter will show less current being drawn by the battery. When the
current stops decreasing, the battery is charged. The start area of the meter indicates a
high rate of current being drawn from the charger. When cranking an engine, the meter
needle will be at the extreme right side of the start area. The 2 amp charge rate may
indicate some activity on the meter, although the meter does not have the resolution to
display this low rate.
Charge Rate Selector Switch
Use the Charge Rate selector switch to select the charge rate or engine starting setting
you require.
Switch #1 -• Use this switch to select the 55 Amp Charge Rate ↔ 140 Amp Engine
Start and the 20 Amp Charge Rate. Switch #2 must be in the down position (Select
Position) when using Switch #1.
Switch #2• - Use this switch to select the 2 amp Charge Rate and the OFF position.
Also, use to select use of Switch #1. Note that Switch #1 is only effective when
Switch #2 is set to “Select Position.”
2A Slow Charge Rate• – Intended for charging small batteries such as those
commonly used in garden tractors, snowmobiles and motorcycles.

•6 •
20A Rapid and 55A Boost Charge Rate• – Use for charging automotive, marine and
deep-cycle batteries. Not intended for industrial applications.
140A Engine Start• – Provides 140 amps for cranking an engine with a weak or run
down battery. Always use in combination with a battery.
OPERATING INSTRUCTIONS11.
This battery charger must be properly assembled in accordance with
the assembly instructions before it is used.
This is a manual charger. Be sure to monitor the charging process and
stop it when the battery is charged. Not doing so may cause damage to your battery or
result in other property damage or personal injury.
Charging
Ensure that all of the charger components are in place and in good working1.
condition, for example, the plastic boots on the battery clips.
Connect the battery following the precautions listed in sections 6 and 7.2.
Connect the AC power following the precautions listed in section 8.3.
Select the appropriate settings for your battery.4.
Turn the charger on.5.
Manual Charging Mode
When a manual charge is performed, the charger will continue to charge and will not
shut off. You must keep a visual check on the ammeter to determine when the battery
is charged. Be sure to monitor the charging process and stop it when the battery is
charged. Not doing so may cause damage to your battery or result in other property
damage or personal injury.
Using the Engine Start feature
Your battery charger can be used to jumpstart your car if the battery is low. Follow these
instructions on how to use the ENGINE START feature.
Follow all safety instructions and precautions for charging your battery.
Wear complete eye protection and clothing protection. Charge your battery in a well-
ventilated area.
Using the ENGINE START feature WITHOUT a battery installed in
the vehicle could cause damage to the vehicle’s electrical system. NOTE: If you have
charged the battery and it still will not start your car, do not use the engine start feature,
or it could damage the vehicle’s electrical system.
Set switch #2 to the OFF position.1.
With the charger unplugged from the AC outlet, connect the charger to the battery2.
following the instructions given in section 6 (FOLLOW THESE STEPS WHEN THE
BATTERY IS INSTALLED IN A VEHICLE).
Plug the charger AC power cord into the AC outlet.3.
With the charger plugged in and connected to the battery of the vehicle, set switch4.
#1 to the engine start position, and set switch #2 to the down position.
Crank the engine until it starts or 3 seconds pass. If the engine does not start, wait 65.
minutes before cranking again. This allows the charger and battery to cool down.
NOTE: During extremely cold weather, or if the battery is under 2 volts, charge the
battery for 5 minutes before cranking the engine.
If the engine fails to start, charge the battery for 5 more minutes before attempting to6.
crank the engine again.
After the engine starts, move switch #2 to the OFF position and unplug the AC power7.
cord before disconnecting the battery clips from the vehicle.
Clean and store the charger in a dry location.8.
NOTE: If the engine does turn over but never starts, there is not a problem with the
starting system; there is a problem somewhere else with the vehicle. STOP cranking the
engine until the other problem has been diagnosed and corrected.

•7 •
CALCULATING CHARGE TIME12.
Find your battery’s rating on the chart below, and note the charge time given for each
charger setting. The times given are for batteries with a 50% charge prior to recharging.
Add more time for severely discharged batteries.
NR means that the charger setting is NOT RECOMMENDED.
BATTERY SIZE/RATING CHARGE RATE/CHARGING TIME
2 AMP 20 AMP 55 AMP
SMALL
BATTERIES
Motorcycle,
garden,
tractor, etc.
6 - 12 AH 2 – 3¾ hrs NR NR
12 - 32 AH 3¾ – 10 hrs NR NR
CARS/TRUCKS
200 - 315 CCA 40 - 60 RC 11¼ – 14½
hrs 1 – 1½ hrs 25 - 32 min
315 - 550 CCA 60 - 85 RC NR 1½ – 2 hrs 32 - 40 min
550 - 1000 CCA 80 - 190 RC NR 2 – 3½ hrs 40 - 76 min
MARINE/DEEP CYCLE
80 RC NR 1¾ hrs NR
140 RC NR 2¾ hrs NR
160 RC NR 3 hrs NR
180 RC NR 3¼ hrs NR
MAINTENANCE INSTRUCTIONS13.
After use and before performing maintenance, unplug and disconnect the battery13.1
charger (see sections 6, 7 and 8).
Use a dry cloth to wipe all battery corrosion and other dirt or oil from the battery clips,13.2
cords, and the charger case.
Ensure that all of the charger components are in place and in good working condition,13.3
for example, the plastic boots on the battery clips.
Servicing does not require opening the unit, as there are no user-serviceable parts inside.13.4
All other servicing should be performed by qualied service personal.13.5
MOVING AND STORAGE INSTRUCTIONS14.
Store the charger unplugged, in an upright position. The cord will still conduct electricity14.1
until it is unplugged from the outlet.
Store inside, in a cool, dry place.14.2
Do not store the clips on the handle, clipped together, on or around metal, or clipped to14.3
the cables.
If the charger is moved around the shop or transported to another location, take care to14.4
avoid/prevent damage to the cords, clips and charger. Failure to do so could result in
personal injury or property damage.
TROUBLESHOOTING15.
PROBLEM POSSIBLE CAUSE REASON/SOLUTION
Charger will not turn on when
properly connected.
AC outlet is dead.
Poor electrical connection.
Check for open fuse or circuit
breaker supplying AC outlet.
Check power cord and
extension cord for loose
tting plug.
The battery is connected and
the charger is on, but is not
charging.
Clips are not making a good
connection.
Check for poor connection at
battery and frame. Make sure
connecting points are clean.
Rock clips back and forth for
a better connection.

•8 •
PROBLEM POSSIBLE CAUSE REASON/SOLUTION
No reading on the ammeter. Charger is not plugged in.
No power at the receptacle.
Clips are not making a good
connection to the battery.
Connections are reversed.
Battery is defective
(will not accept a charge).
2 amp charge rate is being
used.
Plug the charger into an AC
outlet.
Check for open fuse or circuit
breaker supplying AC outlet.
Check for poor connection to
battery and frame. Make sure
connection points are clean.
Rock clips back and forth for
a better connection.
Unplug the charger and
reverse the clips.
Have battery checked.
Ammeter may show no
activity at the 2A charge rate.
Ammeter reading stays high. Battery is severely
discharged.
Wrong battery voltage.
Continue charging battery for
two more hours. If problem
continues, have the battery
checked.
Verify you are trying to
charge a 12 Volt battery.
Ammeter reads less than
selected charge rate when
charging a discharged battery
Extension cord is too long or
wire gauge is too small.
Weak cell or sulfated plate in
battery.
Battery is only partially
discharged.
Use a shorter or heavier
gauge extension cord.
A sulfated battery will
eventually take a normal
charge if left connected. If the
battery will not take a charge,
have it checked.
Continue to charge the
battery.
The charger is making an
audible clicking sound.
Circuit breaker is cycling.
Battery is defective.
Shorted battery cables or clips.
Severely discharged battery,
but otherwise it is a good
battery.
Reverse connections at
battery.
The settings may be wrong.
Check the charger settings.
Have the battery checked.
Circuit breaker cycles when
current draw is too high.
Check for shorted cables or
clips and replace if necessary.
The battery may not want to
accept a charge due to a run-
down state. Allow charging to
continue until battery has a
chance to recover sufciently
to take a charge. If more than
20 minutes, stop charging and
have the battery checked.
Shut the charger off and
correct the lead connections.
Charger makes a loud buzz
or hum.
Transformer laminations
vibrate (buzz).
Shorted Diode Assembly or
Output Rectier Assembly
(hum).
No problem, this is a normal
condition.
Have charger checked by a
qualied technician.

•9 •
PROBLEM POSSIBLE CAUSE REASON/SOLUTION
Short or no start cycle when
cranking engine.
Drawing more than the
Engine Start rate.
Failure to wait 6 minutes (360
seconds) between cranks.
Clips are not making a good
connection.
AC cord and/or extension
cord is loose.
No power at receptacle.
The charger may be
overheated.
Battery may be severely
discharged.
Crank time varies with the
amount of current drawn. If
cranking draws more than the
Engine Start rate, crank time
may be less than 3 seconds.
Wait 6 minutes of rest time
before the next crank.
Check for poor connection at
battery and frame.
Check power cord and
extension cord for loose
tting plug.
Check for open fuse or circuit
breaker supplying AC outlet.
The thermal protector may
have tripped and needs a little
longer to reset. Make sure the
charger vents are not blocked.
Wait and try again.
On a severely discharged
battery, charge for 10 to 15
minutes in the 55 amp rate to
help assist in cranking.
BEFORE RETURNING FOR REPAIRS16.
When a charging problem arises, make certain that the battery is capable of accepting16.1
a normal charge. Double check all connections, the AC outlet for a full 120-volts, the
charger clips for correct polarity and the quality of the connections from the cables to the
clips and from the clips to the battery system. The clips must be clean.
When a battery is very cold, partially charged or sulfated, it will not draw the full rated16.2
amperes from the charger. It is both dangerous and damaging to a battery to force
higher amperage into it than it can effectively use
in recharging.
When an UNKNOWN OPERATING PROBLEM arises, please read the complete manual and16.3
call the customer service number for information that will usually eliminate the need for return.
If the above solutions do not eliminate the problem or for information
about troubleshooting, call toll-free from anywhere in the U.S.A.
1-800-621-5485
7:00 am to 5:00 pm Central Time Monday through Friday
LIMITED WARRANTY17.
WARRANTY NOT VALID IN MEXICO.
SCHUMACHER ELECTRIC CORPORATION, 801 BUSINESS CENTER DRIVE,
MOUNT PROSPECT, IL 60056-2179, MAKES THIS LIMITED WARRANTY TO THE
ORIGINAL RETAIL PURCHASER OF THIS PRODUCT. THIS LIMITED WARRANTY IS
NOT TRANSFERABLE OR ASSIGNABLE.
Schumacher Electric Corporation (the “Manufacturer”) warrants this battery charger for
1 year from the date of purchase at retail against defective material or workmanship that
may occur under normal use and care. If your unit is not free from defective material or
workmanship, Manufacturer’s obligation under this warranty is solely to repair or replace
your product with a new or reconditioned unit at the option of the Manufacturer. It is the
obligation of the purchaser to forward the unit, along with mailing charges prepaid to the
Manufacturer or its authorized representatives in order for repair or replacement to occur.

•10 •
Manufacturer does not provide any warranty for any accessories used with this product
that are not manufactured by Schumacher Electric Corporation and approved for use
with this product. This Limited Warranty is void if the product is misused, subjected to
careless handling, repaired, or modied by anyone other than Manufacturer or if this unit
is resold through an unauthorized retailer.
Manufacturer makes no other warranties, including, but not limited to, express,
implied or statutory warranties, including without limitation, any implied warranty
of merchantability or implied warranty of tness for a particular purpose. Further,
Manufacturer shall not be liable for any incidental, special or consequential damage
claims incurred by purchasers, users or others associated with this product, including,
but not limited to, lost prots, revenues, anticipated sales, business opportunities,
goodwill, business interruption and any other injury or damage. Any and all such
warranties, other than the limited warranty included herein, are hereby expressly
disclaimed and excluded. Some states do not allow the exclusion or limitation of
incidental or consequential damages or length of implied warranty, so the above
limitations or exclusions may not apply to you. This warranty gives you specic legal
rights and it is possible you may have other rights which vary from this warranty.
THIS LIMITED WARRANTY IS THE ONLY EXPRESS LIMITED WARRANTY AND THE
MANUFACTURER NEITHER ASSUMES OR AUTHORIZES ANYONE TO ASSUME
OR MAKE ANY OTHER OBLIGATION TOWARDS THE PRODUCT OTHER THAN
THIS WARRANTY.
Schumacher Electric Corporation Customer Service
1-800-621-5485
Monday – Friday 7:00 a.m. to 5:00 p.m. CST
Schumacher and the Schumacher Logo are registered trademarks of
Schumacher Electric Corporation
To activate the warranty, please ll in the warranty registration card on page 12 and mail it in,
OR go to www.batterychargers.com to register your product online.
DO NOT RETURN THIS PRODUCT TO THE STORE!
Call Customer Service for Assistance: 800-621-5485

•11 •

•12 •
1 YEAR LIMITED
WARRANTY PROGRAM
REGISTRATION
MODEL:___________________ DESCRIPTION:___________________________
This is the only express limited warranty, and the manufacturer neither assumes nor authorizes
anyone to assume or make any other obligation. There is no other warranty, other than what is
described in the product owner’s manual.
The warranty card should be submitted within 30 days of purchase. The customer must
keep the ORIGINAL receipt because it will be required for any warranty claims.
This warranty is not transferable.
Mail To: Schumacher Electric Corporation
801 Business Center Drive
Mount Prospect, IL 60056-2179
Name_______________________________________________________________
Street Address________________________________________________________
City_________________________________State__________Zip Code__________
Phone______________________Email____________________________________
Store Name Where Purchased____________________Date of Purchase__________
Store Location_____________________UPC Number_________________________
Serial Number________________________(SEE PRODUCT)