SciCan Hydrim L11w User manual

Hydrim®L110 w Quick Reference Guide
12 5
order number 01-108367S
Caution:
1. Hydrim Cleaning Solution is compatible with solid
stainless steel instruments that are resistant to
heat and alkalinity.
2. Carbon steel, aluminum, nickel and rhodium-plated
instruments may corrode in Hydrim Cleaning Solution.
Do not process burrs or endofiles in the Hydrim.
3. Do not process stainless steel and carbon steel
instruments at the same time.
For best results:
Use Stat-Dri Plus rinse aid (part number 8OZPLUS) to prevent spotting.
P0 should be used to keep instruments moist when they will not be washed within one hour.
P1 and P2 should be used to wash instruments in baskets.
P3 and P4 should be used to wash instruments in cassettes and heavily soiled instruments.
Replacing the Hydrim Cleaning Solution:
When the chemical indicator light shines continuously, and Ed appears on the display, the solution level
is low and the container is in need of replacement.
1. Open the cleaning solution door.
2. Put a new cleaning solution box into the drawer upside down.
3. Te a r o p en the tab.
4a.Pull out the spout and remove the protective cap.
4b.Attach the hose tightly to the connector on the cleaning solution box.
5. Place the box in the cleaning solution drawer and then close.
3
Shines when cleaning solution needs changing
Flashes when rinse-aid needs filling
8 min.*
20 min.*
30 min.*
30 min.*
40 min.*
Shines when salt needs refilling
*Actual cycle time will vary depending on
incoming water temperature and pressure
4a
4b

Filter Maintenance:
1. Check the filters daily for debris and
remove if necessary.
2. After undoing the coarse filter, the fine
filter can be removed. Remove any debris
from the filter cavity and rinse the filters
under running water.
3. Insert the filter units and tighten the
coarse filter.
Wash Arm Maintenance:
1. Inspect the nozzles and wash arms
weekly for blocked holes due to debris.
2. Pull the lower arm upwards and lift off.
3. Unscrew the upper wash arm collar
and remove the upper wash arm.
4. Clean both wash arms under
running water.
5. Refit the wash arms. Ensure that the
lower wash arm has locked into place
and the upper one is screwed tight.
Refilling the Rinse Aid:
When the chemical indicator light
flashes, you will need to refill the
rinse-aid container with Stat-Dri Plus.
1. Fold back the lid of the rinse
aid container.
2. Pour the rinse-aid into the rinse-aid
container until the level indicator
darkens.
3. Close the lid ensuring you that you
hear it snap. Refilling the Water Softener:
If you have set the water softener to any setting above 0,
the SALT indicator flashes when you need to refill the
salt container.
1. Open the salt container lid.
2. Upon first use of the Hydrim L110w, pour approximately
1 litre (1 quart) of water into the salt container. It is not
necessary to add water during subsequent refills of the
salt container.
3. Using the accompanying salt jug, fill the salt container
to the top (maximum of 1kg / 2.2 lbs.)
4. Close the salt container lid.
For all service and repair inquiries:
United States: 1-800-572-1211, Canada: 1-800-870-7777, International: [phone]
Email: [e-mail]
Hydrim is a registered trademark of SciCan, Division of Lux & Zwingenberger Ltd.
coarse filter
fine filter
level
indicator
chemical indicator light
rinse-aid containersalt indicator light
lid
salt container lid
P.N.96-108366 Rev. 1.0
upper wash
arm collar
lower wash arm upper wash arm